3186 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator Water Leak
4 of 7 people
found this instruction helpful.
-
BRIGIDA from MIAMI, FL
- Easy
- Less than 15 mins
Icemaker waterline leaking inside by the grommet where the water line comes in the refrigerator . First removed the water line from grommet . Then removed grommet by hand from the fridge. Last, reversed prodedure.
Was this helpful?
Thank you for voting!
original shelf shattered during cleaning
4 of 7 people
found this instruction helpful.
-
Steve from La Grange Park, IL
- Easy
- 15 - 30 mins
a simple matter of putting the new shelf back in place an reconnecting the shelving brackets. pretty self-explanatory.
Was this helpful?
Thank you for voting!
switchlight on my refrigerator was not working
5 of 10 people
found this instruction helpful.
-
Eileen from Coto de Caza, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point,
... Read more
it was just a matter of plugging in the new switchlight , which was very simple.
Read less
Was this helpful?
Thank you for voting!
Fan would not turn when the refrigerator came on all the time. Would physically have to turn the fan blades.
2 of 2 people
found this instruction helpful.
-
David from CLIFTON, NJ
- Really Easy
- 30 - 60 mins
Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.
Was this helpful?
Thank you for voting!
freezer too cold and refrigerator not cold enough because fan not working
2 of 2 people
found this instruction helpful.
-
Ann from LAPORTE, PA
- Easy
- 30 - 60 mins
-
Nutdriver
Had to defrost a bit and then was able to remove rear freezer panel by simply removing the 2 screws holding it in place.
Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and r ... Read more ed wires clipped from the old motor. Then reinstalled.
The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.
Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and r ... Read more ed wires clipped from the old motor. Then reinstalled.
The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.
Read less
Was this helpful?
Thank you for voting!
Water Leaking out of bottom of refrig first then out of vegetative bins underneath
2 of 2 people
found this instruction helpful.
-
robert from Vicksburg, MS
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench set
Replaced defrost thermostat and defrost controller and also noticed that run capacitator for compressor almost oxidized in two and ordered and replaced and cleaned out drain tube and invertor (which was blocked by frozen peas and other food)or water to drain during defrost cycle and put everything back together and seems to work fine now.
... Read more
...storing beer in outside refrig now
Read less
Was this helpful?
Thank you for voting!
The front of theDrawer Slilde Rail broke off the rail.
2 of 2 people
found this instruction helpful.
-
Irma from Tylertown, MS
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the 2 drawers and then the glass shelf.
Positioned the drawer slid and tightened to rear screw and the front screw.
Replaced the shelf and the 2 deawers.
What's the big deal? Any 78 year old woman can do it.
Positioned the drawer slid and tightened to rear screw and the front screw.
Replaced the shelf and the 2 deawers.
What's the big deal? Any 78 year old woman can do it.
Was this helpful?
Thank you for voting!
Bracket was broken near the front mounting location causing the rt drawer
2 of 2 people
found this instruction helpful.
-
John from Palatka, FL
- Easy
- 30 - 60 mins
-
Screw drivers
First i removed everything from the bottom shelf, removed the glass, then removed the entire bracket assembly. Then removed the front metal strip to expose the front mounting screw, then removed the rear screw. Installed the new part and reversed the procedure.
Was this helpful?
Thank you for voting!
light kept blinking on and off never same way
2 of 2 people
found this instruction helpful.
-
michael from CENTRALIA, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends
Other Parts Used:
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people
found this instruction helpful.
-
Gerald from WINTERVILLE, GA
- Very Easy
- Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
a fan blade broken causing it to make a loud noise
3 of 5 people
found this instruction helpful.
-
Marnie from Denver, CO
- Really Easy
- Less than 15 mins
-
Pliers
we took off the old one and replaced it.
Was this helpful?
Thank you for voting!
Original evaporator fan (31 years old) was making a lot of worn bearing noise
2 of 2 people
found this instruction helpful.
-
T from SOUTHBURY, CT
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Empty freezer;
Remove shelves and ice trays;
Unscrew and remove the rear vertical panel;
Unscrew and remove fan housing;
Unscrew and remove fan from fan housing;
Fan blade slides off the motor shaft without tools.
Reverse order to reassemble with new fan motor.
I did have to use the wire extensions ... Read more that were included as the replacement motor had the electric connections in a different location from the original motor.
Overall, this was an easy replacement.
Remove shelves and ice trays;
Unscrew and remove the rear vertical panel;
Unscrew and remove fan housing;
Unscrew and remove fan from fan housing;
Fan blade slides off the motor shaft without tools.
Reverse order to reassemble with new fan motor.
I did have to use the wire extensions ... Read more that were included as the replacement motor had the electric connections in a different location from the original motor.
Overall, this was an easy replacement.
Read less
Was this helpful?
Thank you for voting!
Cap on the door retainer bar broke.
2 of 2 people
found this instruction helpful.
-
Mary from New Milford, NJ
- Really Easy
- Less than 15 mins
The replacement cap fit perfectly. Unfortunately when the orinigal cap broke it tookout a small piece of the surrounding plastic leaving nothing for the new cap to catch. I have the piece and tried several kinds of glue but nothing holds it securely enough. I would however readily recommend your company. The service was terrific.
... Read more Thank you.
... Read more Thank you.
Read less
Was this helpful?
Thank you for voting!
The part that holds the items in the door was bent.
2 of 2 people
found this instruction helpful.
-
victoria from forest park, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the brackets with the metal strip attached, from the door. I took a screwdriver and pressed down on the parts holding the strip to the brackets . I attached the new strip to the brackets and then attached the whole thing to the door.
Really easy to do.
Really easy to do.
Was this helpful?
Thank you for voting!
Not cooling and freezer freezing up
6 of 14 people
found this instruction helpful.
-
kenneth from carmel, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled
Was this helpful?
Thank you for voting!