3186 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Old gasket was worn & torn making for a poor seal
1 person
found this instruction helpful.
-
Leonard from Rahway, NJ
- A Bit Difficult
- 30 - 60 mins
Removed freezer door then refrigerator door. Layed it on a big drop cloth to work on it. Replace feeezer door and cover refrigerator opening with plastic or something to help keep the cold in.
Removing old gasket was easy. Just pull it out. Align the new gasket with metal bracket that holds it then firmly hammer it into place. You’l ... Read more l know when it’s attached correctly cause it hugs the door properly.
Removing old gasket was easy. Just pull it out. Align the new gasket with metal bracket that holds it then firmly hammer it into place. You’l ... Read more l know when it’s attached correctly cause it hugs the door properly.
Read less
Was this helpful?
Thank you for voting!
Fridge wasn't cooling and half freezing
1 person
found this instruction helpful.
-
Wendell Hayes from Dillob, SC
- Really Easy
- 30 - 60 mins
-
Screw drivers
Part was perfect fit .Removed fan .three screws.replaced that s it
Was this helpful?
Thank you for voting!
water leaking from under dishwasher
1 person
found this instruction helpful.
-
Edward from E LONGMEADOW, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.
Indeed ... Read more , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Indeed ... Read more , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Read less
Was this helpful?
Thank you for voting!
Slide rail broken at forward mount
1 person
found this instruction helpful.
-
Phyllis C. from Northwood, NH
- Really Easy
- 15 - 30 mins
-
Screw drivers
Took out shelf & brackets. Removed plastic shelf. Unscrewed broken bracket & screwed in new bracket.
Put back in & replaced the shelf.
Put back in & replaced the shelf.
Was this helpful?
Thank you for voting!
I found a broken slide rail after replacing a center slide rail.
1 person
found this instruction helpful.
-
Anna from Weatherly, PA
- Easy
- 30 - 60 mins
-
Screw drivers
I followed the directions on the site for the center slide replacement. I had actually called a local store and had him order the first part. It took several days and then I started searching online and found this site.Then I ordered the second part on line and to my surprise it arrived the next day. I was fortunate enough to have lived
... Read more
only about 70 miles from the distributer.Following the directions I found here is how I attempted the initial repair. With the vegetable bins out fo the bottom, I removed the plate covering the front frame by gently prying it off. Then I removed the two screws to losen the bar and lifted out the glass shelf. I didn't have much difficulty removing the frame since the front piece support for the slide rail that fit into the frame was already broken. I also had to loosen the screws on the back rail. I removed the entire frame and then replaced the side rail reinserting it into the end caps. I replaced the back screws and then the front ones .I replaced the glass shelf and then the cover cap for the shelf.
The only problem I encountered was that I couldn't seem to get the back screws really tight and I don't know why.
The only problem I encountered was that I couldn't seem to get the back screws really tight and I don't know why.
Read less
Was this helpful?
Thank you for voting!
R/S rail was broken draw would not slide in correctly.
1 person
found this instruction helpful.
-
Laurence from Northport, NY
- Easy
- 15 - 30 mins
-
Screw drivers
Took out both draws and glass shelf, removed the entire lower shelf housing. I snapped off the front rail aluminum face to expose the screw. Unscrewed both screws and removed the rail and then just reversed the procedure to put new rail on. It was the most cost effective way of doing it. All the pieces are there on the GE website as long
... Read more
as you know the model number. You will save a lot of money by doing it yourself.
Read less
Was this helpful?
Thank you for voting!
broken right side rail.
1 person
found this instruction helpful.
-
Jorge from Spring Lake, NC
- Easy
- 15 - 30 mins
-
Screw drivers
I had to remove the glass shelve, the two drawers, and the middle rail. Once I did that, I slide the unit out together. I placed the unit on the floor and removed the one screw located on the far backside of the unit. I had to remove a slip cover (it had the kenmore logo and the writting on it) it was a snap on, so no problem. Glad it
... Read more
was not gluded on. After the old part was removed, I put the new part on. Put the two screws back on and snap the cover back on. Then I put the whole unit back in. This included the glassshelve and drawers. The process was pretty easy. Good luck with your change.
Read less
Was this helpful?
Thank you for voting!
Left drawer slide broken replaced both right and left
1 person
found this instruction helpful.
-
Daniel from Chesapeake, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed drawers and glass shelf. Removed screws that hold old slide rails in place. Installed new rails and re-installed cover for vents. Placed assembly back in and installed drawers.
Was this helpful?
Thank you for voting!
Broken light switch
1 person
found this instruction helpful.
-
Deborah from BRADLEYVILLE, MO
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this helpful?
Thank you for voting!
Light went out in refrigerator
1 person
found this instruction helpful.
-
Gary from EAST JORDAN, MI
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this helpful?
Thank you for voting!
40 year old refrigerator brittle light switch fell apart
1 person
found this instruction helpful.
-
Loren from EL PASO, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back
... Read more
in SNAPP
Read less
Was this helpful?
Thank you for voting!
Light Switch Not Working - Needed New Switch
1 person
found this instruction helpful.
-
Joe from SUGAR LAND, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch d
... Read more
islodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Read less
Was this helpful?
Thank you for voting!
My light in the refrigerator was going on and off.
1 person
found this instruction helpful.
-
Nan from PURCELLVILLE, VA
- Very Easy
- Less than 15 mins
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this helpful?
Thank you for voting!
Lights did not work, bulbs were good
1 person
found this instruction helpful.
-
Donita from O FALLON, MO
- Easy
- Less than 15 mins
-
Screw drivers
Took out the light sockets, plugged in the new ones. I found the manual on line to find the part numbers. Parts select parts were perfect
Other Parts Used:
Was this helpful?
Thank you for voting!
Evap fan failed, would need restarted by hand when weather warmed up
1 person
found this instruction helpful.
-
Linda from WILLIAMSPORT, PA
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Repair was super simple. Everything was a direct fit. Hardest part was unloading freezer to access evap motor. My freezer was old making my wire shields very brittle so I cut the shielding and used heat shrink tubing for a neat clean repair.
Was this helpful?
Thank you for voting!