EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3186 - Instructions

All Instructions for the 3186
16 - 30 of 197

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Frame that supports the vegetable drawers was broken on both sides.
12 of 14 people found this instruction helpful.
  • Ellis from San Antonio, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed screws (4 total) that hold everything together. Removed broken pieces; slipped two new side pieces in place, replaced the screws; put entire frame into place, glass shelf on top, drawers in place: Done!!
Was this helpful?
Thank you for voting!
Light in the refrigerator went out
13 of 18 people found this instruction helpful.
  • Paulette B. from Santa Ana, CA
  • Really Easy
  • 15 - 30 mins
After I bought what I thought I needed for the repair. I asked a friend to come over and look at it. He changed the
the light socket and put the same light bulb in and it works great. I am returning the light switch but decided to keep the light bulb.

Getting on the internet was so easy. This was really very simple. Thank you for making what I thought would be a big ordeal into something very simple.

Paulette Johnson
Was this helpful?
Thank you for voting!
Interior light needed replaced
22 of 46 people found this instruction helpful.
  • Leo from TWIN FALLS, ID
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Was this helpful?
Thank you for voting!
fridge quit coolingg / freezing
11 of 13 people found this instruction helpful.
  • JEFF from HAMPTON, GA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
remove lower back cover - disconnect wires to fan motor - place 6" fan to blow on condenser - fridge began cooling & freezing again - ordered part - part arrived - removed fan motor & bracket - cleaned brackets & fan blade - cleaned lint & dust from condenser compartment (took longer to clean than anything else) - replaced fan motor - rep laced cover - was hero with wife ... :-)
Was this helpful?
Thank you for voting!
gasket needed to be replaced
9 of 9 people found this instruction helpful.
  • nora from bristol, PA
  • Easy
  • 15 - 30 mins
first started with the bottom corner then went across the bottom and proceeded to go around the refrigerator. this made it hard to get the last corner in the track. I redid it by getting all four corners set in the track then worked on pushing the sides of the gasket in. This worked much better.
Was this helpful?
Thank you for voting!
Switchlight was broken on tennant's refridge
10 of 12 people found this instruction helpful.
  • Mark from Somers Point, NJ
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapp ed the new switch into place.

10 minutes total.
Was this helpful?
Thank you for voting!
refrigerator did not cool
10 of 14 people found this instruction helpful.
  • Carl from Kent City, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
i put a new evaporator motor in and now it works fine
Was this helpful?
Thank you for voting!
Twice I ordered the oven light bulb & each time the light bulb was defected
18 of 38 people found this instruction helpful.
  • Barbara from BELLEVUE, WA
  • Very Difficult
  • Less than 15 mins
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Was this helpful?
Thank you for voting!
Fan had quit; needed replacement.
10 of 15 people found this instruction helpful.
  • John from Divide, CO
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
The fan was the correct part. It arrived one day after my well trained son-in-law had left for Texas. I had to install the motor myself. He had trained me well; it was not hard. the most difficult was getting the two tabs on the fan housing to fit back into the frame of the refrigerator where they belonged. Thanks. the part & deliver y were overpriced, but I needed seed and convenience. Thanks for getting it right the first time.
John Moragues
Was this helpful?
Thank you for voting!
Noisy freezer evaporator fan, bearings worn out
8 of 10 people found this instruction helpful.
  • Todd from Saint Paul, MN
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
UNPLUG UNIT. Open freezer compartment, top door. You may want to let it warm up a bit before beginning work. Next remove single screw from small square plastic grate at top left back of freezer compartment with phillips screw driver. Remove green ground wire connection behind removed grate with nut driver. Next remove 2 screws at top of freezer compartment holding plastic air diffuser bracket in place and holding back panel. Remove metal back panel of freezer by pulling top towards you, then angle out of compartment. Evap. fan is now exposed. I inspected and removed fan by removing two screws with nutdriver on bracket behind fan blade. I inserted nutdriver (with long socket driver)between fan blades to screws on bracket behind blade - 1 each side. After these two screws are removed, pull fan and bracket assembly out from plenum. Remove wiring from motor and remove motor to workbench. Remove round metal clamp from fan hub with needle nose pliers and slide off fan blade from motor. Also remove bracket and rubber bushing. Disgard old motor. Inspect and clean blade. Replace if necessary. Reattach rubber bushing, bracket THEN fan blade to new motor. New fan has atleast one terminal in new location and I had to use one wire extension that came with kit. Route wire behind motor and plug in new wires to back of motor. Insert fan and bracket to plenum, hold in place with one hand while reattaching screws with nutdriver between fan blades. Once fan is in place and nuts secure, I tested operation by plugging unit back in to make sure new motor ran and fan spun freely. Reattach back panel, top diffuser bracket and small grate with 3 screws. Shut door, set temp. and wait 24 hours before loading freezer. Unit good as new!
Was this helpful?
Thank you for voting!
noise from condenser fan
10 of 17 people found this instruction helpful.
  • donald from opelousas, LA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
disconnect the power to the unit. remove the retainer sctrews on the mounting bracket. remove fan motor from unit. using the rerquired tools remove the fan from the old motor and install on the new one. torque the nut until all slack is out then 1/4 turn. reinstall motor assy. and reconnect power. test the system .
Was this helpful?
Thank you for voting!
Broken rails - drawers do not close well
6 of 6 people found this instruction helpful.
  • Stephen from Charlotte, NC
  • Easy
  • 30 - 60 mins
  • Screw drivers
Very easy. Removed all the parts from the fridge. Removed the glass. Unscrewed the two screws holding the rails to the front and rear support. The front support that has the "fruit" and veggie" settings, you have to remove the plastic name cover off to expose the front screws. The install is the reverse of the removal. The only "tricky" p art is remembering the configuration (left from right) and removing the vinyl edging that the glass rests on from the old left and right rails and placing it on the new rails. Good Luck to all! "Quality is not an act, it is a habit" - Aristotle
Was this helpful?
Thank you for voting!
stopped making ice
7 of 9 people found this instruction helpful.
  • Timothy from Orange Park, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver
First I turned off the water supply. Then I removed the ice bin and the ice maker by removing 4 screws and 3 electrical connections. This allowed access to the evaporator fan which was not moving. To remove the evap fan I removed two screws that hold the fan bracket. The fan assembly now had to be pushed back and rotated to remove fro m hole. There are 3 electrical connections that have to be disconnected from the fan, one ground wire that also is connected to the fan bracket and 2 power connections. Installing the new fan was the reverse of the above except the power connections were in a different location and i had to use the extension wires provided with the new fan to have the length needed to make the connection.
Was this helpful?
Thank you for voting!
needed to repair the door shelf retainer bar and end cap
7 of 9 people found this instruction helpful.
  • Margaret from East Elmhurst, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
first I removed the old inside shelf, very easy and then replaced with new inside shelf retainer and end caps, which all lock into each other and make the process quick and easy.
Was this helpful?
Thank you for voting!
broken fan blade in the freezer compartment
7 of 9 people found this instruction helpful.
  • John from Cumberland, MD
  • Really Easy
  • Less than 15 mins
  • Pliers
Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.
Was this helpful?
Thank you for voting!
All Instructions for the 3186
16 - 30 of 197