EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3186 - Instructions

All Instructions for the 3186
31 - 45 of 197

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator and freezer were not cooling
6 of 6 people found this instruction helpful.
  • Michael from NEW BERN, NC
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
Vacuumed the area around the compressor, removed the PTC relay switch cover, pried the broken relay switch off the unit with a screw driver and replaced with the new relay switch. Replaced the backing of the refrigerator and tested, within minutes the work was confirmed.
Was this helpful?
Thank you for voting!
Old gasket damaged/worn
6 of 7 people found this instruction helpful.
  • Dale from Hutchinson, KS
  • Difficult
  • 30 - 60 mins
I had to figure out how to remove the old gasket and install the new one on my own since there were NO INSTRUCTIONS. The old gasket had to be cut off; the new one had to be warmed in hot water to make it flexible enough to flatten out. Once that was done, I had to trim excess plastic from the inside corners before the gasket would press i nto place at the corners.
Was this helpful?
Thank you for voting!
Old gasket was torn and leaked
5 of 5 people found this instruction helpful.
  • Kevin from Red Oak, TX
  • Really Easy
  • Less than 15 mins
This was much easier than I anticipated.
The most time doing the repair was waiting for the water to soften the new seal.
The old one pulled right out, she cleaned it off and I pushed the other into place.
Part select got it to me quicker than expected and when I phoned the order in and inquired about whether I neede d the retainer behind it she asked someone and found I did not which saved me $16.
They are great and this whole transaction went too smooth...
Was this helpful?
Thank you for voting!
missing center cover slide for vegetable bins
6 of 8 people found this instruction helpful.
  • Jean from Tucson, AZ
  • Really Easy
  • Less than 15 mins
I took out the vegetable bins and slid in the part. Replaced vegetable bins. Works perfect. I was told locally that GE doesn't make the part any more and that I wouldn't be able to find one. First place I looked on the net was you and found it with no trouble at all. really thrilled to get it. Thanks
Was this helpful?
Thank you for voting!
Bracket Holding The Meat Drawer Broke
5 of 5 people found this instruction helpful.
  • del from tuscaloosa, AL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Found the part I needed in only a few minutes on the website and ordered it in less than 5 minutes. The part came within 2 days and I simply removed 2 screwes from the old part and installed the new part and replaced the 2 screws , the easiest repair job that I have ever done in my home. Thanks
Was this helpful?
Thank you for voting!
light not working
7 of 11 people found this instruction helpful.
  • robert from FRANKLIN SQ, NY
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.
Was this helpful?
Thank you for voting!
The refigerator not getting cold and the freezer coils where a solid block of ice while the refrigerator never turned off.
4 of 4 people found this instruction helpful.
  • Robert from Augusta, GA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
After finding your web site, the description of my problem was pretty clearly referenced as to what parts where the likely problem. When I received the parts it was only a matter of unplugging the refrigerator, removing the cover in the freezer and cutting and stripping the two color coded wires for the thermostat and wire nutting the wir es and putting wire tape on them. Then put the coil cover back on. Then in the refrigerator section, remove the controls cover and then take the controls compartment loose and unfasten the old defrost control, and install the new one. Then put every thing back in place. Plug the refrigerator back up and set the temperature to medium.
Was this helpful?
Thank you for voting!
There was a warm spot at the front edge of dividing wall. The fan motor was not working.
4 of 4 people found this instruction helpful.
  • Kathrine from FORT MILL, SC
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
I followed the directions of Steve on the installation video. He makes it easy to do the repair with his step by step description of the installation. I have repaired three different aging appliances with help of Steve and PartSelect's very helpful Customer Service.
I wish Steve a wonderful retirement and hope PartSelect can find someone as easy to follow for future videos. The videos are priceless for the repairs.
Was this helpful?
Thank you for voting!
replace torn gasket
4 of 5 people found this instruction helpful.
  • Dawn from Waldorf, MD
  • Difficult
  • More than 2 hours
  • Screw drivers
The part arrived It said to warm it to take out wrinkles but not even a picture of how to take off the old or put on the new. Everything on the internet in general about gaskets explained about unscrewing the old gasket but I couldn't find any screws. The user feedback mentioned no tools and that was our only clue and the only reason we finally succeeded. We looked at it repeatedly over 5 days. Pulled and pushed and could not figure out how it was attached or how to unattach without breaking things. I finally got out a screw driver and tried to pry it off. An hour later I got a corner piece started to come off. We pulled all the way around and got it off easily once started. We again struggled to put the new one on. Couldn't really tell what area of the gasket fit back into the crease. It kept falling off. Finally we pushed the correct edge of the gasket into the crease. VERY difficult. Fat edge fits into skinny crease. Took a lot more strength than expected so it didn't seem right but it was. Took a while and a lot of strength to work the corners and sides in. Eventually got the whole thing on. A picture and 4 sentences would have been a big help. Wouldn't try it again. To anyone else...No screws. Use a lot of strength. I hope someone publishes a picture for you.
Was this helpful?
Thank you for voting!
Refrigerator light wouldn't come on.
4 of 5 people found this instruction helpful.
  • Daniel from Crown Point, IN
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.
Was this helpful?
Thank you for voting!
Difficulty in removing the old switch
5 of 8 people found this instruction helpful.
  • James from Federal Way, AL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.
Was this helpful?
Thank you for voting!
Both side rail guides had broken
3 of 3 people found this instruction helpful.
  • Carol from Bowie, MD
  • Easy
  • 30 - 60 mins
  • Screw drivers
I first unscrewed the broken right rail from the back piece and replaced with the new rail. Did the same for the left piece side. Attaching to the front rail was challenging because I took a while to figure out how to remove the cover (where the pictures of the vegetables/fruits are). But if you just get a narrow flat-head screwdriver und er there, it just pries off. Then you can get to the little screw that attaches the side rails to the front piece.
Was this helpful?
Thank you for voting!
Interior Light did not go on due to faulty switch
4 of 6 people found this instruction helpful.
  • Robert from Coto de Caza, CA
  • Really Easy
  • Less than 15 mins
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this helpful?
Thank you for voting!
end cap to bar of freezer door broke
3 of 4 people found this instruction helpful.
  • Kimberly A from Columbus, OH
  • Really Easy
  • Less than 15 mins
Snapped end cap onto bar and installed bar onto freezer door.

I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
Was this helpful?
Thank you for voting!
Left Vegetable Drawer Slide Rail was broken thus making it impossible for the Crisper Drawers to function properly.
4 of 7 people found this instruction helpful.
  • Philip from McCordsville, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the Glass Shelf on top of the Vegetable Drawer assembly, unfastened the front rail from the broken slide rail and removed the entire assembly. I cleaned the parts and then installed the new rail. I placed the drawers in the repaired assembly and placed in the refridgerator. It really went well. I didn't need the other parts order. I only had them just in case they were needed.
Was this helpful?
Thank you for voting!
All Instructions for the 3186
31 - 45 of 197