31203 Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven wouldn't ignite
8 of 8 people
found this instruction helpful.
-
Treasure from High Point, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
Read less
Was this helpful?
Thank you for voting!
long delay before igniting - long time for oven to heat up
8 of 9 people
found this instruction helpful.
-
Dace from Arcata, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
The repair was easy. Partselect processed my order quickly and my part was delivered sooner than I expected.
Removing the old igniter was simple. I took off the oven door to create easy access to the oven. I then unplugged the connection and removed the screws that held the older igniter in place. Installing the new ignit ... Read more er was almost as easy. I followed the same steps as above, but in reverse. I accidentally dropped one of the screws, so installation probably took 1 minute longer than removal. :)
I'm a very satisfied customer.
Removing the old igniter was simple. I took off the oven door to create easy access to the oven. I then unplugged the connection and removed the screws that held the older igniter in place. Installing the new ignit ... Read more er was almost as easy. I followed the same steps as above, but in reverse. I accidentally dropped one of the screws, so installation probably took 1 minute longer than removal. :)
I'm a very satisfied customer.
Read less
Was this helpful?
Thank you for voting!
Could not turn the oven on or off.
7 of 7 people
found this instruction helpful.
-
Christine from Indio, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Lifted the top up, only a few inches as the possibality of kinking the gas line was a issue. Took two screws out and replaced the unit, threaded the thermostat down through the oven. It was a breeze. I am 68 year old woman and did I myself.
Most importantly, the process of getting the part was amazing, ordered it in the AM and receiv ... Read more ed it the next day (no extra charge)and by miday the range was good as new. Great service!
Most importantly, the process of getting the part was amazing, ordered it in the AM and receiv ... Read more ed it the next day (no extra charge)and by miday the range was good as new. Great service!
Read less
Was this helpful?
Thank you for voting!
Seal was fallinig off
7 of 8 people
found this instruction helpful.
-
Marilyn from Fresno, CA
- Really Easy
- Less than 15 mins
My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.
Was this helpful?
Thank you for voting!
Oven floor panel was warped.
8 of 11 people
found this instruction helpful.
-
Cindy from Colton, CA
- Really Easy
- Less than 15 mins
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 11 people
found this instruction helpful.
-
John from Caliente, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Parts came very quickly from PartSelect. Good service.
Was this helpful?
Thank you for voting!
thermostat went out
9 of 14 people
found this instruction helpful.
-
brenda from redding, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Had to take off burners and lift off top. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and removed old element. Then I did all steps in reverse to install new thermostat.
Was this helpful?
Thank you for voting!
Oven wouldn't heat
6 of 6 people
found this instruction helpful.
-
Adawel from Brooklyn, NY
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
First I removed the burner to which the igniter was attached to. Then I attempted to removed the two screws holding the igniter in place. However, these screws proved to be difficult. I called a local appliance repair shop and the person I spoke to explained how the screws were designed to go one way. Any attempt to remove these screws wo
... Read more
uld result in the threading to be stripped and virtually impossible to remove. (I have never heard of these type of screws before) Anyway, he recommended a hack-saw. Well, the hack-saw worked. After that, the replacing of the part was very easy. Igniter works perfectly and now my wife is ready to conquer the bake sales.
This was my first time using partselect.com.
Yes, I will recommend them to other homeowners.
Thanks. A.T
This was my first time using partselect.com.
Yes, I will recommend them to other homeowners.
Thanks. A.T
Read less
Was this helpful?
Thank you for voting!
spark ignition in stove failed to turn on burnes.
7 of 10 people
found this instruction helpful.
-
David from Upland, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical.
... Read more
I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.
Read less
Was this helpful?
Thank you for voting!
oven wouldnt light or would light inconsistently
6 of 7 people
found this instruction helpful.
-
Jay from Hubbard, TX
- Easy
- 30 - 60 mins
-
Nutdriver
igniter would heat but oven wouldnt come on or would intermittently.opened door a little and lifted it off removed racks and bottom shield removed wingnut and burner shield,removed 2 screws holding igniter ,took off lower shield to allow access to plug,unplugged old one plugged in new one replaced shield and 2 screws holding igniter,put o
... Read more
ven back together in reverse order,works like new :) ps if unit not unplugged from wall be careful igniter is hot with electricity and will bite you OUCH!
Read less
Was this helpful?
Thank you for voting!
Igniters were flaky on 2 burners and almost dead on 2
7 of 10 people
found this instruction helpful.
-
Matt from Craig, CO
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the uti
... Read more
lity drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
Read less
Was this helpful?
Thank you for voting!
black dirty burner grates
14 of 31 people
found this instruction helpful.
-
Carolyn from St. George, UT
- Really Easy
- Less than 15 mins
replaced grates
Was this helpful?
Thank you for voting!
Burners would not ignite flame...Had to start with match.
6 of 7 people
found this instruction helpful.
-
Richard from Los Angeles, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Removed the old burners with a Plumbing Pipe Wrench by turning 1/4 turn counter clockwise. Disconnected (2) wires and replaced with new Sealed Burners. The simmer burner wires were slightly diffrent from the original but they do fit by opening the connector with screwdriver and then clamping once wire inserted.
Was this helpful?
Thank you for voting!
Burners would not ignite
6 of 7 people
found this instruction helpful.
-
Charles from Kalamazoo, MI
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed cover from igniter, took off wires, replaced wires on new one, secured in place, put cover back on.
Was this helpful?
Thank you for voting!
My oven wouldn't light.
6 of 7 people
found this instruction helpful.
-
Anna from Valparaiso, IN
- Really Easy
- 15 - 30 mins
-
Nutdriver
I located the igniter element, and remove the two screws that hold it in place. I then went around to the back of the oven and located the wire, and disconnected it. Then I pulled it out through the oven and removed it. I then replaced it with the new element; pushed the wires through to back of the stove and plugged it in. With that
... Read more
done, I screwed the new igniter element into place. I then put my oven back together; pushed it back into place and turned the gas back on. And presto! my oven lights like new again. I saved myself the costly repairman visit, and the job was easy.
Read less
Was this helpful?
Thank you for voting!