EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31203 Magic Chef Range - Instructions

All Instructions for the 31203
1 - 15 of 540

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not work but the Broiler did
337 of 374 people found this instruction helpful.
  • James from Ferndale, MI
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and f ound this site that explained it was possible for the igniter to glow but if it was not drawing the correct amperage (because its resistance was too high) then the main brain would not allow the gas valve to open. So I took a look at the broiler and it had the same igniter. I measure the resistance of both of them and the oven igniters resistance was higher (don't rememeber the reading) then I moved the Igniter from the broiler to the oven and the oven worked from there it was just a matter of ordering the part. End of story except for I am still doing all the cooking on the barbecue outside.
Was this helpful?
Thank you for voting!
Oven wouldn’t heat up properly
249 of 284 people found this instruction helpful.
  • James from Berwick, ME
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
My oven has two igniters so I needed to determine which one was the problem.

Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read 2.7 amps with a rated amp between 3.3 and 3.6. So that was the culprit.

Replacing the igniter was easy. Two screws and a wire connected with a plug. I was able to do the diagnosis and unplug the wire without pulling the oven out. I pulled the drawer out and removed the two screws in a cover behind where the drawer was. You may not be so lucky…I have long arms.

I found removing the oven door made it easier to reach the igniter itself. To remove the door just open it slightly and pull up, it should come off easy…and replace in opposite manner.

Keep track of your screws and put it back together the way you found it except for the igniter that is.

Anyone with moderate technical skill could easily do this repair. The diagnosis is the hard part. I estimate I saved about $200 doing it myself.

Good luck.
Was this helpful?
Thank you for voting!
A burner wouldn't spark strongly enough to light the gas.
168 of 188 people found this instruction helpful.
  • Matthew from Brookfield, MA
  • Really Easy
  • Less than 15 mins
  • Pliers
Replacement of these burners is very easy. You just twist the burner counterclockwise a quarter turn and pull it out. (You may need a big wrench if the range is very old.) Once out, just pull the two wires off and push them onto the new burner. Crimp them on with pliers if they're loose -- mine were. Twist the burner back on.
If the gasket under the burner has disintegrated, don't worry about it. They don't offer replacements for them because they're not necessary as a safety feature. They were designed to keep overspills from running under the cooktop, but the ridge around the hole is likely higher than you'd ever need.
Was this helpful?
Thank you for voting!
gas burner ignitor failure
142 of 162 people found this instruction helpful.
  • roy from East Providence, RI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed t hat rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Was this helpful?
Thank you for voting!
Oven would'nt light
132 of 146 people found this instruction helpful.
  • Charles from Charlestown, RI
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
In most cases if your oven won't light or takes a long time to light you may have a bad igniter even if it glows. To check the igniter use a voltmeter to check for 120 A/C volts going to the igniter and3.5 A/C volts going between the ingniter and the gas valve. My bad ingniter glowed but had only only 3.0 A/C volts going to the gas valve for the oven. The new igniter took only 45 minutes to install and supply's 3.6 A/C volts to the gas valve and the oven works fine.
Was this helpful?
Thank you for voting!
oven failed to light
71 of 79 people found this instruction helpful.
  • Beryl from Dawsonville, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
My son replaced the broiler igniter this spring, so I had a clue as to what was required. This was even easier and since I had back surgery recently & my husband was out of town that was a giant plus!

I unplugged the oven, removed the oven door, found the release latch and removed the oven floor. I then removed the 2 screws that held the igniter in place (I received this stove used and the igniter had evidently been replaced before as it was the same shorter version included in the kit). I pulled the igniter out then removed some insulation and tugged the connector out of the oven floor. I disconnected the igniter and plugged the new one in. I then replaced the connector in the floor, attached the igniter with the screws, replaced the insulation and did a test run (plugged in the oven & turned it on). That was successful so I put the floor back in and put the door back on.
Ta-Dah!
Was this helpful?
Thank you for voting!
Our oven would not heat up, smelled like gas.
67 of 76 people found this instruction helpful.
  • Theresa from Yorkville, IL
  • Easy
  • Less than 15 mins
  • Screw drivers
I removed the oven door, unscrewed a couple of screws, replaced the ignitor, put screws back in, done! Sometimes it would take my oven up to an hour to heat up and sometimes it just wouldn't heat up, just fill the house with a gas smell. Now, it heats up in about 3 minutes!! We were considering buying a new oven, we will just keep this o ne. $40.00 beats $700.00
Was this helpful?
Thank you for voting!
Oven would not ignite
57 of 61 people found this instruction helpful.
  • Jerry from Paris, TN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
This repair project was too easy!...and cheap. Sears quoted the price of the igniter at $280 plus the service call and the item cost $41 on PartSelect. The part was received the next day after the order was placed...WOW! So easy, turn off the power to the oven, open the oven door, remove the oven racks and lift the bottom pan of the oven up from the back and set it aside. There you see the flat type igniter in plain view at the back of the oven. Remove two screws with nuts using a nut driver (I had trouble because the screws were corroded and I had to use some, um, force to get them out and swore a little too). Once the screws were out, pull the igniter elecrtic wires and connector from the entrance hole in the back after moving a little insulation out of the way. Release the connector plug and unplug the old igniter and simply plug in the new one. Find new screws and reinstall in reverse order. Be sure to push the connector and wiring back into the hole and cover with the insulation. Very easy job that anyone could do.
Was this helpful?
Thank you for voting!
Oven would not turn on
58 of 65 people found this instruction helpful.
  • William from Newkirk, NM
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
First I pulled out the oven from the cabinet. Disconected the power, I removed the cover from the back, disconected the wires from the igniter. Removed the igniter from inside the oven. Reversed the process to install the igniter. Turned on the oven, it worked. Sat down and had a beer.
Was this helpful?
Thank you for voting!
Oven not working
49 of 60 people found this instruction helpful.
  • JEREMY from ARLINGTON, TN
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
There were no flames when I turned the oven on, so the first thing I did was narrow down the problem through the process of elimination. It was really a fairly simple system to work on. I verified that it was getting power to the hot surface igniter (which it was). You can check this visibly by seeing if it heats up and glows, but that i s not enough. You also have to make sure the igniter is drawing enough amps to open the oven safety valve ( about 3-3.5 amps). You do this by leaving everything connected and turning the oven on as normal. You clamp the Amp Meter (a clamp style Amp Meter works best)to the wires going into the Hot Surface Igniter and checking amperage. If the amperage is to low then the igniter is not pulling enough to open the valve and you should replace it. If the amperage is as it should be then the valve is not opening. The next thing is to turn off the gas to the appliance and unplug the electricity before starting any other work. I removed the oven racks and bottom decking out of the way so I would have room to work. I removed the oven burner to get to the oven safety valve, which is held in by two screws. I disconnected the gas line coming in to the valve using an adjustable wrench, removed the two wires (noting their position) and removed the two screws with a phillips head screwdriver. I replaced the valve with a new one and hooked everything back up in reverse order. That was all there was to it. I also replaced a couple of burners on the top of the stove while I was at it, only because they were difficult to light sometimes. They simply twist out counterclockwise and have two wires that you can't get confused because they have different size connectors and will only go on one way. This 10 year old stove now works like a new one.
Was this helpful?
Thank you for voting!
glow bar would light but oven would not light
39 of 42 people found this instruction helpful.
  • David from Van Nuys, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
I removed the rear access panel on the oven in order to get to the igniter wires. While testing the output voltage of the old igniter when on, I found that it was producing less than 3 volts ac. This was my clue that although the igniter glowed, it was going bad and needed to be replaced. I unpluged the oven, shut off the gas feed to the oven then removed the oven bottom pan (pull two push pins back, lift up and out) and removed the burner baffle wing nut with baffle. This gave easy access to the igniter and it's two mounting screws which i removed using a phillips screw driver. I unpluged the old igniter from the connector, pluged in the new one after routing it through the access hole from inside the oven to the back of the oven where the connector is located.
Mounted the new igniter, replaced the burner baffle, baffle nut, oven bottom, rear access panel cover, checked and turned on the gas, plugged the oven back in and sure enough it fired up right away. if you check the system of how your oven works and find the problem, it's easy to fix it yourself and save serious money...and look like a hero to the rest of the family.
Was this helpful?
Thank you for voting!
top burners on stove won't ignite ,no clicking noise
48 of 73 people found this instruction helpful.
  • scott from centreville, VA
  • Easy
  • 15 - 30 mins
remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems.
Was this helpful?
Thank you for voting!
No spark at top burners, first one then eventually all 4.
35 of 41 people found this instruction helpful.
  • jonathan from Bryson City, NC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Most of the repair time was spent researching the problem online, locating the spark module inside the range, and selecting the part online. Installation was easy. Key troubleshooting info for me was, if there is no clicking, the spark unit is probably worn-out. I traced the ignition wires from the burners down to the spark module, locate d inside a 2x3" metal housing next to the bottom drawer. I removed 2 screws and out it came. The replacement unit pictured on the PartSelect site was not identical to the original but had the same number of contacts. I ordered the part and it arrived a few days later. The old connectors slipped easily onto the new pins, and I screwed the new unit into the range using the new metal housing. All 4 burners now spark up quickly, and we saved at least $100 on a service call. It was well worth the time and effort -- thanks!
Was this helpful?
Thank you for voting!
Burner Was Worn Out
31 of 32 people found this instruction helpful.
  • arnold from la punte, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Burner head arrived when I got home from work. Just timely to cook for dinner that monday night, got the 4 burners disconnect the element from the old burner, then connect element to the new bunners, in less than 10 mins, and I had save estimate $600 buying a brand new stove or gas range, this will last me another5 to 10 years. Espec ially this time of recession
Was this helpful?
Thank you for voting!
worn out door seal
31 of 32 people found this instruction helpful.
  • Stella from Charlotte, TN
  • Really Easy
  • Less than 15 mins
  • Pliers
removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door.
Was this helpful?
Thank you for voting!
All Instructions for the 31203
1 - 15 of 540