31203 Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burner wouldn't start
35 of 48 people
found this instruction helpful.
-
Yury from Brooklyn, NY
- Really Easy
- Less than 15 mins
Make a quarter turn counterclockwise, disengage a burner head, disconnect 2 wires, connect to a new head, install turn clockwise.
That's it!
That's it!
Was this helpful?
Thank you for voting!
Oven would not light
29 of 30 people
found this instruction helpful.
-
Richard from Austin, TX
- Easy
- 1- 2 hours
-
Pliers, Screw drivers
This oven was located in a rental house I own.
I first removed the metal plate that covers the burners at the bottom of the oven. No tools required for this step.
Next I turned the oven to 300 degrees, waited 30 seconds and noticed that the igniter was glowing brightly, but the burners did not light.
I nex ... Read more t turned the oven controls off, pulled the plug, and set to work removing the 2 screws holding a plate to the back oven wall and the 2 screws holding the igniter to the burner. These last 2 screws had corrosion on them and I needed to use vise-grips to get a firm hold on them. During reassembly these screws no longer held firmly because the hole they threaded into was enlarged during disassembly.
With the screws loose I pulled the igniter and fished the wires connected to it through the opening until I saw the connector. I then pulled the stove out of its opening and saw that there was a easily removable metal cover over the wires, and I took it off.
The new igniter came with an incompatible plug, so I cut off the connector on the stove wiring and on the new igniter and used wire nuts to make the new connections. I kept the orientation of the old and new plugs the same way in case the wiring mattered, but that was just being safe. I don't know if the igniter cares which of its wires go to which wire on the stove.
I reinstalled the screws holding the igniter, and shoved short sections of the supplied wiring into the screw holes so that the screws would hold more tightly. I shoved the supplied insulation into the opening that the wires passed through, and reattached the cover at the back of the stove.
I shoved the stove back into its opening, turned the oven on and it lit within 15 seconds.
I was very happy with the result, and the product I ordered arrived on time, well packaged and I'm a very happy customer.
I first removed the metal plate that covers the burners at the bottom of the oven. No tools required for this step.
Next I turned the oven to 300 degrees, waited 30 seconds and noticed that the igniter was glowing brightly, but the burners did not light.
I nex ... Read more t turned the oven controls off, pulled the plug, and set to work removing the 2 screws holding a plate to the back oven wall and the 2 screws holding the igniter to the burner. These last 2 screws had corrosion on them and I needed to use vise-grips to get a firm hold on them. During reassembly these screws no longer held firmly because the hole they threaded into was enlarged during disassembly.
With the screws loose I pulled the igniter and fished the wires connected to it through the opening until I saw the connector. I then pulled the stove out of its opening and saw that there was a easily removable metal cover over the wires, and I took it off.
The new igniter came with an incompatible plug, so I cut off the connector on the stove wiring and on the new igniter and used wire nuts to make the new connections. I kept the orientation of the old and new plugs the same way in case the wiring mattered, but that was just being safe. I don't know if the igniter cares which of its wires go to which wire on the stove.
I reinstalled the screws holding the igniter, and shoved short sections of the supplied wiring into the screw holes so that the screws would hold more tightly. I shoved the supplied insulation into the opening that the wires passed through, and reattached the cover at the back of the stove.
I shoved the stove back into its opening, turned the oven on and it lit within 15 seconds.
I was very happy with the result, and the product I ordered arrived on time, well packaged and I'm a very happy customer.
Read less
Was this helpful?
Thank you for voting!
oven wouldnt maintain temperature
30 of 34 people
found this instruction helpful.
-
Patricia from Plainfield, IL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
First I removed the oven grates and then the metal plate that covers the burner and igniter.Then I removed the two screws that hold in the igniter,be careful because the threads on the sheet metal screw strip off easily due to the heat. Then I slid out the storage drawer on the bottom of the stove.Next I removed two screws that hold on a
... Read more
cover in front of the gas valve where the igniter is plugged in.I unplugged the old igniter, removed it then replaced it with the new one.I then reassembled everything in the reverse order.I did have to use a nut and bolt to replace the damaged sheet metal screw.
Read less
Was this helpful?
Thank you for voting!
porcelan on igniter broken (2)
31 of 46 people
found this instruction helpful.
-
paul from mc neal, AZ
- Really Easy
- 30 - 60 mins
-
Screw drivers
remove 2 screws that hold element in place, remove element, replace with new element, and replace screws , replaced burner assy on other
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven & Broiler Failed to Ignite
25 of 29 people
found this instruction helpful.
-
John from Baltimore, MD
- Really Easy
- Less than 15 mins
-
Nutdriver
First I removed the oven door for easier access then, removed the oven grates and bottom pan. Then there is a wing nut that holds the heat deflector in place over the manifold thats needs to be removed. Now you can see the igniter, remove the 2 small hex head screws and disconnect electrical connection.
Simply reverse the sequence to ... Read more reinstall.
This may sound like alot to do but it only took 15 minutes to complete and I'm not an appliance repair person. Anyone who is somewhat of a handyman can accomplish this job.
Simply reverse the sequence to ... Read more reinstall.
This may sound like alot to do but it only took 15 minutes to complete and I'm not an appliance repair person. Anyone who is somewhat of a handyman can accomplish this job.
Read less
Was this helpful?
Thank you for voting!
oven takes a long time to reach temp set point
23 of 25 people
found this instruction helpful.
-
Scott from Brooklyn Park, MN
- Really Easy
- 15 - 30 mins
-
Screw drivers
i need to replace the lower oven igniter about 2-3 years
unplug the oven
open the oven door half way then slide the door up
take out both racks
push the bottom pan away from you and lift up
one screw holds the igniter on
pull the wire out until you get to the electrical plug
disconnect
unplug the oven
open the oven door half way then slide the door up
take out both racks
push the bottom pan away from you and lift up
one screw holds the igniter on
pull the wire out until you get to the electrical plug
disconnect
Was this helpful?
Thank you for voting!
oven burner would not come on.
20 of 20 people
found this instruction helpful.
-
Theodore C. from Winsted, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I am a retired lp Gas service person so this was quite
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.
Was this helpful?
Thank you for voting!
Oven wouldnt ignite
20 of 23 people
found this instruction helpful.
-
Rodney from Menomonee Falls, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver
Turned gas and electricity off first. Pulled out the bottom pan so I could access the igniter. Removed two screws holding the igniter next to the burner tube, unplugged the igniter from the back of the stove and then pulled the plug threw into the oven. Mounted new igniter and then pulled the plug threw and plugged it back in. Reinstalled
... Read more
bottom pan and I was done in 15 - 20 minutes. VERY EASY TO DO...
Read less
Was this helpful?
Thank you for voting!
Oven would not maintain set temperature. Oven flame would take a long time to re-ignite causing oven to cool down more than 100 degrees before re-igniting.
18 of 20 people
found this instruction helpful.
-
Jack from Millington, NJ
- Easy
- Less than 15 mins
-
Nutdriver
Step1: Remove oven door. Open oven door about 3-4 inches and pull up with 2 hands.
Step2: Turn oven light ON so you can see.
Step3: Remove bottom tray by pulling on the 2 rear clips and lift tray up and out of the oven.
Step4: Using a nut driver remove the 2 nuts holding the ignitor in place. If nuts are ... Read more rusted from heat spray a tiny bit of WD-40 on them and totally wipe off any excess when finished removing the nuts.
Step5:Pull wire from old ignitor through the insulation and unplug it from its connection.
Step6: Plug in new ignitor and push it back through the insulation and fasten it back in position with the 2 nuts.
Step7: Re-install bottom tray and door and CONGRATULATIONS cause you just saved yourself about $150! by DIY And you never again will be eating semi-raw chicken or better yet, take the money you just saved and treat yourself and your family to a sushi dinner.
I would like to thank Partselect.com for their quick delivery and very reasonable price on the Ignitor I purchased.
Regards.
Step2: Turn oven light ON so you can see.
Step3: Remove bottom tray by pulling on the 2 rear clips and lift tray up and out of the oven.
Step4: Using a nut driver remove the 2 nuts holding the ignitor in place. If nuts are ... Read more rusted from heat spray a tiny bit of WD-40 on them and totally wipe off any excess when finished removing the nuts.
Step5:Pull wire from old ignitor through the insulation and unplug it from its connection.
Step6: Plug in new ignitor and push it back through the insulation and fasten it back in position with the 2 nuts.
Step7: Re-install bottom tray and door and CONGRATULATIONS cause you just saved yourself about $150! by DIY And you never again will be eating semi-raw chicken or better yet, take the money you just saved and treat yourself and your family to a sushi dinner.
I would like to thank Partselect.com for their quick delivery and very reasonable price on the Ignitor I purchased.
Regards.
Read less
Was this helpful?
Thank you for voting!
Burners would not ignite
19 of 23 people
found this instruction helpful.
-
Craig from Sequim, WA
- Easy
- 15 - 30 mins
-
Screw drivers
Pulled the stove out from the wall. Removed the left side of the stove. Removed the wires from the old igniter. Modified four of the wire ends with the proper size spade connectors (supplied with the new part). Reinstalled the wires onto the new part. Tested the burners. Reinstalled the stove side. Moved the stove back into position.
Was this helpful?
Thank you for voting!
Oven wouldn't lite
20 of 27 people
found this instruction helpful.
-
E Blake from Dauphin Island, AL
- Easy
- 15 - 30 mins
-
Screw drivers
Pulled off the oven door, just lift straight up. Pulled out the floor of the oven, very easy just lift from the back. The only problem I had was the screws holding the old igniter wouldn't come out, they just spun. I snipped them off and picked up two new ones at the hardware store. Pull the wiring harness in through the hole in the b
... Read more
ack of the oven. Unsnap old wiring harness, snap in new one. Reattach the new igniter, replace floor, replace door. Turn on oven and cook food... fairly easy repair.
Read less
Was this helpful?
Thank you for voting!
oven comes on to temp but will not reheat to a new temp third time trouble with same range
17 of 18 people
found this instruction helpful.
-
william from newport, VT
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
first of all i have one advantage even though i am 70 yrs old i had a appliance shop for sears in the 60s and 70s and have not forgotten to much of the basics i am still in the security business and up on electronics. last time i had the company repair the oven , 70 dollars for the part 75 dollars for the svs call. (first igniter was
... Read more
on full warranty) well this time i decided to look for trhe part myself, i just went on line typed in oven repair parts and eventually all these sites came up. yours was the most professional looking and i took a chance. guess what everything you promised you delivered. price quality USA made parts and delivered in three days . opened package went to work less than fifteen minutes back in business.
will sure use you again if the need arises thank you
will sure use you again if the need arises thank you
Read less
Was this helpful?
Thank you for voting!
Had broken the gas tubes from going to the orvice.
16 of 19 people
found this instruction helpful.
-
John from Wolcottville, IN
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Removed (4) screws that hold the orfice assemblies in place. Removed the 4 nuts from the gas feed tubes. Placed the two new orfices in place and attached the nuts. Replaced range top and replaced the (4) screws into the orfice assemblies. Done. Worked fine the first time.
Was this helpful?
Thank you for voting!
Gas oven took longer and longer to light off even though glow igniter was glowing. When the time grew to 10 minutes and more I knew a repair was needed.
15 of 16 people
found this instruction helpful.
-
Joseph from West Hartford, CT
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
I first removed the bottom of the oven and the flame guide to uncover the igniter assembly. Then I applied WD40 to the two Philip head screws and unscrewed them to release the old igniter. The two wire leads from the igniter went into the back of the oven and I could not reach the connection block. So I pulled the oven out far enough to g
... Read more
et behind it and took off the panel covering the electrical wires in back. I had previously disconnected the electrical cord from the wall outlet. After I determined that I could not remove the connection block I returned to the igniter and cut the two existing wires close to the ceramic igniter assembly. I marked the top wire with a Sharpie pen so that I would not mix up the new leads when I install the new igniter. Although it was awkward to work inside the small oven space I was able to strip the insulation back about 1/2 inch and then connect the new igniter wires using the twist caps supplied with the kit. I pushed the wires back into the space and added the insulating material supplied. The igniter assembly was then installed with the original two screws and the other oven covers and flame guide reinstalled easily. After reconnecting the power outlet the oven was back in operation with ignition of gas flame within a minute or so. It was a good feeling and now we do not need to consider replacing the gas range.
Read less
Was this helpful?
Thank you for voting!
burner would not light; ignitor did not produce spark
16 of 20 people
found this instruction helpful.
-
Candace L. from Woodinville, WA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Take a few screws off the back of the slide in burner module. Take off the back. Unscrew the ignitor screw, remove ignitor carefully, replace with the new ignitor, put the screw back in, put the back back on, try it out! Ours worked after a couple of tries - don't know if the ignitor had to "rev up" by several sparks or we just didn't
... Read more
have it properly installed at first. Anyway, very easy. Did it in my pajamas on a Saturday morning.
Read less
Was this helpful?
Thank you for voting!