EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31203 Magic Chef Range - Instructions

All Instructions for the 31203
31 - 45 of 540

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not light; dings in the porcelin top
14 of 15 people found this instruction helpful.
  • Richard from Fanwood, NJ
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The bottom burner would not stay lit. I determined that it was as a result of the ignitor's voltage droping. The thing still glowed red but apparently the voltage drops and closes the gas valve. So, I switched the broiler one with the bottom one to see if it would work. It did. Then I bought the new ignitor and put it in where I had t aken the broiler ignitor out. You have to take care to put the insulation back and shove the connector well into the hole so that there is no possibllity of it melting. I also replaced the oven top. I had bought that part a couple of years ago because I had dropped some things on it and it was chipped. When I got the top I thought it would be somewhat intuitive as to how to replace it. But, it wasn't. So,it stayed in its box. When I had the other problem I decided to tackle the top too. First turn off the gas and unplug the oven. You have to pry the top off with a screw driver. Then, you disconnect wires which run to the ignitor for each burner. You also have to disconnect the gas lines running to each dial. Now, you take the top off. To get the burners off the top you have to take a pair of channel locks and open them wide, wrap a rag around the burner and turn them like screws. Under the top there is an assembly that holds the gas lines in place. that has to be removed from under each buner. These assemblies are not interchangeable!!! One is left and the other is right. You then reverse everything. Put the burners in by screwing them down. Its hard but if you put a rag over them you can strike them with a rubber mallet. Screw the gas line assemblies into the bottom of the top. Then hook up the wires and then the gas lines. Then, you pop the top back in. There are those pressure clamps that hold the top down. I made a mistake with the gas line assemblies and switched them. So, when I tested the repair I realized I had the front dial controlling the rear burners and vice versa. Some day I take it all apart and fix it again!
Was this helpful?
Thank you for voting!
Oven Did Not Heat Up !!!!!!!!
16 of 21 people found this instruction helpful.
  • MICHAEL from VAN NUYS, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I realized where the ignitor was and I turned off the circuit breaker took the v plate off with a little tie nut unscrewed the 2 small nuts and small plate to hold wires in and pulled the pig tail wire out and unplugged it and then took new one and installed it in reverse order done in 7 minutes thanks michael
Was this helpful?
Thank you for voting!
Oven stopped while the wife was cooking.
15 of 18 people found this instruction helpful.
  • Marsha from Concord, MA
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
Range is 20+ year old 'condo issue' and difficult to pull from wall since previous owner had tiled it in. Going in from the back was going to be a pain.
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws hol ding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!
Was this helpful?
Thank you for voting!
Sealed burner caps were rusted within and gas leak through the bottom of the caps
13 of 13 people found this instruction helpful.
  • j from bridgewater, NJ
  • Easy
  • 15 - 30 mins
Just used a car oil filter band type wrench and rotated the sealed burner cap a 1/4 turn. cleaned up the rust and dirty. Replaced it with the new cap and tightened it with a 1/4 turn by hand. Instruction can be found on Maytag gas installation manual. The burners are working well and just like a new range.
Was this helpful?
Thank you for voting!
Gas range would not light
16 of 23 people found this instruction helpful.
  • Mike from Menlo Park, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Replaced spark module but same problem persisted. Realized that the insulation on the spark ignitors were all cracked, causing a short.

Lesson learned: check the condition of the spark ignitors first as these have a tendency to crack. Even the smallest crack will cause a short.

Ordered new spark ignitors and plan t o complete repair.
Was this helpful?
Thank you for voting!
Rubber gasket failed due to age
14 of 18 people found this instruction helpful.
  • Mary from Woodland, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I learned that I could clean the window in the oven door. In taking it apart I saw that the gasket had fallen into the oven door. I found the part online, it arrived in three days. I removed the metal part of the door, removed what was left of the old gasket and put in the new one. Put the metal part of the door back on, and it was as g ood as new.
Was this helpful?
Thank you for voting!
Burners would not light and the flame would come out from the bottom of the burner.
13 of 15 people found this instruction helpful.
  • juan from aurora, IL
  • Easy
  • 15 - 30 mins
A quarter turn counter-clockewise and the burner came out. Disconnect the old wires and connect the new wires. Place the burner in its place and a quarter turn clockwise and it was set.
Was this helpful?
Thank you for voting!
The burner igniter would not spark to light the burner.
13 of 17 people found this instruction helpful.
  • Margie from San Antonio, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I had to unscrew 4 screws on the burner unit and then 2 screws on each igniter. slip the olds out and the new ones in and then replace all the screws. And wa la they sparked and I was cooking again.
Was this helpful?
Thank you for voting!
burner head was rusted out. ordered 1 to see if part was correct. ordered 4 more to finish job.
13 of 17 people found this instruction helpful.
  • Robert from Somerville, TN
  • Really Easy
  • Less than 15 mins
unscrewed old burner head ;disconnected 2 wires; repaced with new burner head and replaced wires. Unfortunately, before we really needed to replace the other burner heads, the cooktop itself developed a gas leak. We decided to replace the whole thing, and therefore would like to return the unboxed, unused 4 remaining burner heads.
Was this helpful?
Thank you for voting!
Broke pipe to two front burners
12 of 15 people found this instruction helpful.
  • Nathaniel from New York, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench set
I took off the stove burner and seal (turn counterclockwise by hand.) Then detached the yellow and orange wires by hand. Using a screwdriver, I unscrewed the cover. Then used a 1/2" wrench to unscrew the broken orifice and attach the new orifice.
Was this helpful?
Thank you for voting!
oven won't stay light
10 of 10 people found this instruction helpful.
  • Shannon from Lake Park, IA
  • Easy
  • 15 - 30 mins
  • Screw drivers
removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.
Was this helpful?
Thank you for voting!
oven was only turning on occaisionally
14 of 22 people found this instruction helpful.
  • Shayne from Angoon, AK
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
I took the oven bottom out and then removed the screws that cover the safety valve, then I pulled the oven out and undid the safety valve in the rear of the oven. This was all accomplished with the electricity off and the propane also turned off. I then reinstalled the safety valve.
Was this helpful?
Thank you for voting!
Door Seal on oven was old, hard and breaking apart.
10 of 11 people found this instruction helpful.
  • Kenneth from Friend, NE
  • Really Easy
  • Less than 15 mins
  • Pliers
It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.
Was this helpful?
Thank you for voting!
burner didn't self ignite or control flame
9 of 10 people found this instruction helpful.
  • Geoffrey from Columbus, GA
  • Really Easy
  • 15 - 30 mins
  • Pliers
The burners turn and lift. I replaced two. One turned very easily, the other was stuck so I used liquid wrench and plumbers pliers. I did get it off. Once off, the old wires slipped right off and onto the new burners. Those twisted on very easily. Good as new easy breezy.
Was this helpful?
Thank you for voting!
oven would not heat up.
8 of 8 people found this instruction helpful.
  • Marc from Abington, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove the oven racks. Slide the two catches, located at each rear corner of the oven bottom, toward the front of the oven.

Lift the rear edge of the oven bottom slightly, then slide it back until the front edge of the oven bottom clears the oven front frame. Remove oven bottom from oven.

Pulled storage drawer out to the first stop position. Lift up front of drawer and pull to the second stop position.
Grasp sides and lift up and out.

Under storage area, I removed two screws to remove a steel plate. In the oven, I removed two screws that held on the Oven Igniter. Unplugged the Igniter under the storage area.

Plugged in the new Oven Igniter, replace the two screws that held the Oven Igniter, replace the two screws for the steel plate. Put the storage drawer back, the bottom of the oven back and the racks.

It was easier than I though it would be.
Was this helpful?
Thank you for voting!
All Instructions for the 31203
31 - 45 of 540