EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31203 Magic Chef Range - Instructions

All Instructions for the 31203
76 - 90 of 540

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
the burner cap on my maytag gas range was rusty on the inside and didn't allow the cap to sit flush-causing gas and flames to leak from under the cap
4 of 5 people found this instruction helpful.
  • julie from harrodsburg, KY
  • Really Easy
  • Less than 15 mins
installation was very simple and took less than 5 minutes. first unscrew the burner cap and then remove the 2 wires. to replace reconnect the 2 wires to the new cap and twist cap into place-simple.
Was this helpful?
Thank you for voting!
Lack of burner gas ignition
5 of 8 people found this instruction helpful.
  • Andrew from Lufkin, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I used the other good burner assembly to isolate the problem to the igniters or the igniter block. I ordered both parts from Parts Select. They shipped the parts promptly and after 10 minutes of install time, the burners worked flawlessly.
Thank You Parts Select.
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people found this instruction helpful.
  • peter from marine city, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Was this helpful?
Thank you for voting!
oven wont heat up
4 of 5 people found this instruction helpful.
  • Crystal from Tonawanda, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
it was actually pretty easy, it took about 20 minutes to fix, i had to unscrew the bottom portion of the oven to get to the Igniter on the bottom, then unscrew the Igniter, take off the old pice, and snap the new one in, put it all back together, and that was about it, i had dinner done by the time my husband got home from work. thanks
Was this helpful?
Thank you for voting!
oven wouldn't heat causing the house to smell of gas
3 of 3 people found this instruction helpful.
  • James from Washburn, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
took out racks removed 2 screws holding igniter removed 4 screws on back of stove and unplug igniter. reversed the order installing the new one
Was this helpful?
Thank you for voting!
No spark, bad igniter
3 of 3 people found this instruction helpful.
  • Tom from REDDING, CA
  • Really Easy
  • 15 - 30 mins
1. Grab the old burner and twist counter-clockwise. 2. Unplug the wire from the old igniter, simply pull off. 3. Take new burner/igniter (this new one comes all-in-one) and reattach the wire to the igniter underneath. 4. Place the burner so the 'nubs' line up with the stove top and then twist clockwise a short amount, it should tu rn slightly to lock in place. 5. Test. Mine sparked and started better than it has since i have had the stove
Was this helpful?
Thank you for voting!
Oven igniter went out of my oven.
3 of 3 people found this instruction helpful.
  • Doreen from DOUGLAS, WY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
Took the bottom out of oven then removed and replaced with the new part. VERY EASY! I'm a 70-year-old woman and do quite a few home repairs myself.
Was this helpful?
Thank you for voting!
No spark at top burners
7 of 15 people found this instruction helpful.
  • Joseph from East Freetown, MA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years
Was this helpful?
Thank you for voting!
Burners were rusted and rotten from the bottom, flames were coming from around the bottom
3 of 3 people found this instruction helpful.
  • Alberto from Houston, TX
  • Really Easy
  • Less than 15 mins
all i did was twist the burner counter-clockwise unplug 2 wires and installed the new ones, real easy, it took me about 7-8 minutes for the 4 burners, that was all, our stove is working like new now, albert
Was this helpful?
Thank you for voting!
Oven and burners wouldn't light
3 of 3 people found this instruction helpful.
  • Kory from Collingswood, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Easy repair. I removed the module housing at the back of the stove (two screws) and slipped the wires off the old spark module (I had to use pliers to gently pull one or two wires off--it's an old stove). The existing wires slipped right on the new module. I did have to use the mounting adapter that came with the kit, but that was the fiddliest part of the whole repair. It took me longer to move the stove out and back than it did to do the repair.
Was this helpful?
Thank you for voting!
rusted out burner on stove top
4 of 6 people found this instruction helpful.
  • Roger from Mission, TX
  • Really Easy
  • Less than 15 mins
  • Pliers
turned burner counterclockwise and removed it reversed procedure and installed new one..
Was this helpful?
Thank you for voting!
Oven wouldn't heat.
3 of 3 people found this instruction helpful.
  • Thomas from La Crescenta, CA
  • Easy
  • Less than 15 mins
  • Nutdriver
Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pus hed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.
Was this helpful?
Thank you for voting!
Replaced igniter in right rear burner
5 of 9 people found this instruction helpful.
  • Marty from Kennesaw, GA
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Simply remove the box containing the two right burners. Access the igniter by removing about 8 screws and pull the coupler for the igniter off with a pair of needel nose pliers. Replace with new igniter using the same tool. Re-assemble the box by screwing in the screws and give it a try. Worked great. Once slight hitch, be sure you d on't leave a second screw driving in the box. As it will raddle. So I had to remove and reassemble twice. I'm not a surgeon! Thanks for the fast delivery!
Was this helpful?
Thank you for voting!
The old sealed burner cap had rusted out allowing gas flame around the base of the cap.
3 of 3 people found this instruction helpful.
  • John from Stephentown, NY
  • Really Easy
  • Less than 15 mins
Note the position of the electrode on the side of the old burner cap. Turn the old burner cap one-eighth turn counter-clockwise to loosen and remove it. Raise the burner cap and disconnect the push-on connector wires from the ground and electrode. Clean the surface and connect the electrode and ground connector wires correctly to the n ew burner cap and place the burner cap back in the opening, positioning the electrode at the same orientation as it was with the old burner cap. Turn the cap one-eighth turn clockwise until the burner is snug. Turn on the burner control to test that the burner functions correctly. Make sure there is no smell of propane or gas when the burner is not in use which might indicate that the burner is not properly fitted snugly.
Was this helpful?
Thank you for voting!
Leaking gas from sides of burner
3 of 3 people found this instruction helpful.
  • Homero from SEAGOVILLE, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Counterclockwise turn old burner to remove. Unplug attachment wires. Replug wires place back in place turn clockwise. Done.
Was this helpful?
Thank you for voting!
All Instructions for the 31203
76 - 90 of 540