2048 - Instructions

plires took off the two hoses , on clip the two snap clips . pulled out the old pump . put the new one in cliped in the snap clips in & hook the hoses back up

Pull Washer out, Flip to the right on it's side. Pop two Metal retaining clips, squeeze hose clamps with pliers. Remove pump, sand shaft with dremil or 80 grit sand paper. Replace with new pump. Easy! Push washer back and attach hoses and power. Done 15 minute repair

Removed the two spring clamps from hoses; removed hoses from pump. Removed spring clips holding pump to motor. Had to pry pump off of motor shaft due to rust on shaft end. Sandpapered rust off of shaft and then lubed same with oil and new pump slid easily onto motor shaft. Re-snapped spring clips to hold pump onto motor and then rein ... Read more stalled hoses and their spring clamps. Whala, end of story, job well done.

Disconnected power, water, and drain then moved washer away from wall. Put down some 2x4's to protect hoses and flipped washer on its back. Removed hoses with pliers, removed clips holding pump to shaft, and installed new pump. Reversed process and tested with just water be fire washing clothes.

Unplugged the washer. Pulled it away from the wall far enough so it would be stable tilted back against the wall. That way I didn't have to disconnect any hoses or lay the machine down.

I used a ViceGrips to squeeze the hose clamps and then pulled the hoses off. Getting the pliers in the right position in the tight space was th ... Read more e hardest part of this whole job, and that still wasn't particularly hard. I have medium sized hands (for a man).

I flipped open the retainer clips with my fingers. Pulled the pump off and slid the new one on. It helped to make sure first that the flat side of the motor shaft was roughly facing the same way as the slot in the pump.

I reattached the hoses and popped the retaining clips back on. Held my breath and ran the washer. No more leak!

Incidentally, before I discovered PartSelect I called Whirlpool service. I asked if they could have the tech show up with the part. They said "No." I'd have to pay the fee for a diagnostic visit and then the tech could order parts and return to install them. They said there would be no service charge for the return visit.

Several years ago I believed this story when I called for a dryer repair. However, when a second technician returned with the part I had told the dispatcher the first time around was needed, he came up with some excuse why there had to be a supplemental service charge. I challenged it on my credit card and eventually got it removed, but it was a hassle.

Thank you PartSelect! And thanks to others who posted their experiences and gave me confidence to fix it myself.

Remove four screws securing control panel from the rear and tilt control panel forward. Unplug wiring harness from door limit switch. Unsnap and remove two S-clamps securing enclosure to back panel. Tilt enclosure slightly forward and remove it from wash machine. Disconnect water hoses and clips securing water pump and remove water pum ... Read more p. Install in reverse order. Caution: inspect water hoses closely. I had a rotten pump intake hose and found out the hard way (water everywhere).

Isolated problem to front section of washer by elevating and adding water. Once I identified the pump as leaking (it was pretty obvious:>)I used a screwdriver to release the snaps that hold the pump to the drive motor. After sliding the pump off of the drive motor I used the pliers I release the clamps on the two hoses. Next I logged o ... Read more n to Partselest.com and ordered a replacement. The item arrived in two days. I placed the pump on the motor first then connected the hoses. It was much easier to slide the hose clamps to the proper position with the pump held secure on the motor.

Using the part select website, I discovered that 64% of the time, replacing the water pump will fix the drain problem so I ordered that part. I laid the washer on it's back. And was able to unclip the water hoses, detach the pump and install the new one. The parts select website has great instructional videos to help but in this case, t ... Read more he video recommended removing the outer skin from the washer which I found unnecessary.

Used online instructions from this site

Just removed the old pump with a pair pliers and snapped the new one on. It was a snap

I shut off the water supply hoses and then disconnected them and also disconnected the power supply cord--next I laid the washer on its back being sure to place a block near the water supply valve so the weight of the washer does not rest on the water valve--next I disconnected the inlet and outlet hoses from the pump--next pop off the tw ... Read more o retainer clips on the pump and then remove the pump by sliding off of the motor shaft-----to re- assemble just reverse the procedure and you are done--it is a very easy fix.

I Removed hose clamps and 2 pump clamps. I took the old pump(had a small hole burned in it) off and replaced it with the new pump. I replaced the 2 pump clamps and the hose clamps and it was ready to go.

Unplugged the washing machine. Removed the two philipps screws holding the control panel. Swung it up , disconnected interlock connector, and pried the two clips. Removed the top and cabinet assembly to have easy access to the leaking pump.
Disconnected the two hoses connected to the pump. Used the plier to loosen the hose clamps. Re ... Read more moved the two retainers securing the pump. Removed the old and damaged pump and replaced with the new one. Reinstalled the retainers back on. Reconnected the hoses and clamps. Put the top and cabinet assembly back on. Snapped back the clips and reconnected the interlock connector. Screwed the control panel assembly to the cabinet. Done. Ran the washing machine to check for leaks. Found none.

First of all, it would have been helpful to have two people take the housing off the frame. One to lift and the other to disconnect the hoses that need to come off the pump and the filler.

Second, THANK YOU to another person that posted about prying the pump from the motor and sanding it to accept the new pump. When I couldn't ... Read more get the pump off the motor due to rust, I thought both the pump and motor were done. But I worked the pump off the motor shaft (I had to break the old pump, but it was toast anyway) and used a wire brush and sandpaper to clean the shaft. When I got the new pump, it slid on like a champ!

I also used the parts list that came with the washer to make sure I got all the parts back together in the right place. Like I said, I took too much apart and didn't pay attention to what I was doing for later reassembly. Even though the parts list that came with the washer is small and not to scale, it helped me put the thing back together.

I got my part when PartSelect promised and I got help here from the website. I will use this company whenever I need an appliance part.

First I had to have my wife help me tip the washing machine over so we can get at the pump which we suspected was leaking.

We searched partselect.com and found the part and ordered it and it arrived after a few days.

At first the part won't fit because the metal rod that was supposed to rotate the pump was badly rust ... Read more ed. So we had to buy a file set ($9.95) from Home Depot to file the rust away so that the part will fit.

Filing took a long time to do and was very tedious but after the metal rod was filed away, the pump fit and that's all it took.

There were actually only 2 clamps you have to remove. One at the back and one out front that holds the pump in place. After removing those clamps then it was easy to attach the new pump (after filing the metal rod).

Thanks partselect.com :-)