2048 - Instructions

I am more than happy to relate this...my 15 month old Whirlpool washer was having a slow leak. Initially, I did not suspect it was the water pump because the appliance was fairly new. When I flipped the washer over, I saw clearly it was comming from the water pump. This pump comes right off after you snap off two clips and loosen two hose ... Read more clamps. Takes all of 2 minutes! I took the part off and looked for a part number. Then I punched in the part number on my internet and low and behold parts select was one of the links that came up. I just cliqued my way through the order and FEDEXed the part. It came the NEXT BUSINESS DAY! I had it snapped back on and that took another 2 minutes. Don't pay anyone to do this, it's a shame...it's sooooo easy and Partsselect will ship you the part next day. This repair cost me 67 dollars (34 for the part and shipping). Could have easily been 150.00 by a repair man. EASY JOB...NO DOUBT ABOUT IT

After 3 years of hard daily use, the small feet that hold the Bleach dispenser in place broke off. The new dispenser was easy to snap into place and now the washer is good as new.

Removed the two clips holding the pump to the motor, Lift pump off motor and twist pump to allow easy access to hose clamps. Slide clamps off of pump housing, remove hoses and reverse the process just described.

First I located the leak and removed what was lated identified as the water pump. The pump was secured to a motor by two clamps. Attachted to the water pump were two water hoses. I removed the water pump, took it inside my and started my search for the part on the web. I located your site, followed the site instructions and found the part ... Read more I needed. For the record, I have never attempted to repair anything in my life. Your site help me save over $300.

firts i tilt machine over removed water hoses and released water pump lock clips and pulled out. to replaced its reverse process

Tipped washer for access to pump. Disconnect hoses. Snap spring clips off of pump. Remove pump from motor shaft. Scotch-Brite shaft, push new pump onto shaft. Reconnect hoses. And your done

Job was not as bad as I had thought it would be. This sites instant repairman was a really big help ! I did not take the back off, instead I just put machine on its back and changed out the pump from the bottom. Worked out great and was faster.

I removed the washing machine away from the wall. Put a pillow on the floor and set the machine on its back. I removed the clamps that hold the hose with the pliers and then pump came right off. Replaced with the new one and thats all. I spend exactly 2 minutes doing this fix. My wife still thinks I am a heroe :)

Easiest fix ... Read more I ever done!!!

It was as simple as undoing 2 clamps and removing 2 hoses then just perform that in reverse to put the part back on. And in 10 mins i was using the washing machine.

This is the same part that is on many Maytag washers. I cannot believe it leaked so soon. I spent 45 minutes or better on the phone with Maytag/Roper. Went through at least 5 people (as I was disconnected once), transfered to someone else mid sentence because I bought it at Lowes. I mean as soon as I said Lowes it was like, beep done. ... Read more Oh and by the way after all that they still could not find the part I was looking for let alone give me a price. I was looking on the internet while on the phone and found this place. The prints/drawings are awesome and my part came in about 3 days standard shipping. I have book marked this site and will go nowhere else. The repair took about 5 minutes, poped off the old part and on with the new. I only used pliers to disconnect the water so I could move the washer out.

Layed washer on back side
Removed two clips holding pump ,and two clamps on hoses removed pump installed new very,very easy
only needed a pair of pliers.

First I removed the clamps that holds the pump in place.
Next I removed the water hose clamps.
Then I did the reverse to finish the repair.

I pulled the machine out about two feet from the wall. No need to disconnect any hoses. Tip up the front, place an automotive jack stand under the front of the machine to hold it approximately a foot and a half up. Lay on the floor, remove the hose clamps, flip the two spring clips off that hold the pump, and it's off in minutes. Place th ... Read more e new pump in position and replace the two spring clips, slide the hoses back on and install the clamps. It couldn't be easier or quicker. Replacing the pump took 5-10 minutes max. The longest part of the project was cleaning up the spilled water..!

pulled the washer away from the wall and turned it on its side. I had to remove the gear box and motor to get to the part. Had to remove the whole insides. Install the part and put everything back in.

All the gaskets needed to be replaced on the Briggs 6.75 flathead I was rebuilding. I ported and polished the ports and shaved the eyebrow between the valves and the piston. The gasket set was a perfect fit. It is a monster now. It doesn't sound like a lawnmower engine anymore