2048 - Instructions

undone 2 hoses and popped off brackets

First unplug washer and turn water off (both hot and cold) You only need to pull washer out away from wall about 1 1/2 feet. Take a putty knife and slide under the front corner of the control panel ( both sides one at a time) lift up corner as you slide putty knife under the corner. After both sides are released on the control panel sl ... Read more ide control panel forward( about an inch) to release rear of panel and flip panel over the top. Unplug the lid safety switch then with a screw driver unsnap the cabinet straps one on both sides that were under the control panel. Put screw driver into the spring strap end closest to you and push screw driver back which will release the straps( one on each side). Next tilt the cabinet toward from the back( about 6 ") and lift up about 2 " the cabinet can now be removed. Undue the two hoses on the water pump that is located at the bottom of the washer in the front ( make sure you catch the water from the hoses in a small pan). Undue the two spring clips that hold the pump on. Pull pump straight out (about 1 ") discard old pump and install new one in reverse order. When reinstalling the cabinet there are two stubs on the bottom bracket on the washer that have to put into the slots in the lower front corners of the cabinet ( the hardest part of the whole project is putting the cabinet back on, the trick is what I described above with the slots in the lower front corners. Good luck it very easy to do.

Of course I tried to determine where the leak was from. There wasn't a solid flow of water and was confined to the front. Pulled the washer out and laid it down. Noticed that a metal clip had a little corrosion on it and followed it back to the water pump seal. Removed two hoses and unclipped the pump. That's it. No screws or nuts. Looks ... Read more like it was expected to fail and was easy to replace. It did last for 20 years though.

This was very easy. I just pushed the retaining clips off of the pump body (one top side, and one on the bottom) with my fingers. Then I used a pair of channel lock pliers to compress and relocate the spring clamps down the two hoses away from the pump body to remove their clamping action. I removed the hoses, then pulled the pump off ... Read more of the motor shaft. I lined up the motor shaft with the flat spots in the new pump and installed the new pump in the reverse order. This process took about five minutes and was super easy.

I turned the washer on to see if I could determine where it was leaking from. After I figured out that it was the pump that was leaking, I ordered a new pump. I went with next day shipping because at our house, we can't go long without a washer and the cost for the shipping was worth it. Had it installed in 10 minutes, only tool needed wa ... Read more s a pliers to remove the hose clamps, piece of cake repair!

I pulled out the washer, laid it on it's back, pulled off the two hoses using pliers for the clamps, pulled back two clips, pulled off the pump from the shaft, put the new pump on the shaft, and did the reverse of the above. It was a simple operation and made even more satisfying by the prompt delivery of the part, within 2 days. Thank yo ... Read more u for that, and I will use your services in the future if needed.

After unplugging power and disconnecting water drain hose, I pulled the washer out aprox four feet from the wall and leaned it back against the wall. I then used a lamp at the end of an ext cord to light up below the washer where the water pump was attached and it was easy to remove and replace! I carefully replaced the washer in its orig ... Read more inal location and reconnected power and drain hose. The job was complete in 15 minutes! Wow!

I noticed a leak on the floor. I check the hoses for tightness on the back of the washer and the hoses going to the facets and drain. After disconnecting the hoses going to the washer, facet and drain, I then flip the washer on it's back and examined the underside for wetness. All the underside hoses appeared to be not leaking. I then ... Read more disconnected the two hoses going to the pump with channel-locks, and I disconnect the two clips holding the pump with just my hand and removed the water pump. I then poured water into the hoses' opening on the water pump itself, and I discovered a slow leak occurring from the shaft area on the water pump. I searched PartSelect and luckily found a water pump that matched. I then installed the new water pump (after receiving it a few days later) in reversed procedures of disconnecting the old water pump. I tested the washer by adding a little bit of water into the washer then switch the dial to spin cycle in order to empty the water inside the washer--no leaks occurred and I was extremely happy.

Flip washer on its back, Undo/flip the clips/clamps off the water pump, remove the clamps from the hose and remove hoses from water pump, slide the pump off the direct drive, line up the shaft/drive with the new water pump and slide into position and return the clamps to secure water pump in place and reattach water hoses and clamp to the ... Read more water pump. There should be two hoses going to the water pump, flip washer back upright and run a cycle to make sure the problem has been fixed

Unfortunately my washer cabinet did not come off as in the video so I had to do repair from underneath. The rest of the repair worked exactly like the video showed. I had a couple of small, sturdy wood boxes about 9" high which I used to brace the washer after tipping it backwards a bit (and unplugging it too). My wife acted as a spott ... Read more er to be extra safe. The only two things that required the hook tool and mirror were: 1) Working from the bottom my hands were at an awkward angle so I couldn't pop the retainer clips off the pump, but a hook tool (like a screwdriver with a hooked end) popped them off easily, and 2) The other issue was once the new pump was in place I could not locate the slot for the top retainer clip until I could look at it with the telescoping handle mirror, and then I was able to put the clip in by feel. Extremely easy repair, especially with the guidance from the video. Thanks for video help! WH

My husband got the part within 2 days of the order and replaced the leaking pump within a half hour. The repair was very quick and easy for him and your company's prompt delivery prevented my floor from getting wet everytime I did a load of laundry. Thank you and we will continue to get parts from your site in the future--hopefully we ... Read more won't need to anytime soon. but we know you are there if we need to repair!

I press using the plier the spring retainer to removed the two hose from the defective pump.
I used screw driver to removed the two retainer.I pulled the pump away from the shaft of the motor. Replaced with new pump, align to the motor shaft and return back the two retainer. It is easy and its good to have my parts right on time.

1) Disassembled the lid
2) Took the front Panel off (the old water pump was in the bottom left hand corner in plain site).
3) Used flat head screw driver to gentle pry the top and bottom water pump fasterners.
4) Used pliers to remove top hose camp. Note this is where I discovered why everyone says to put the washer on it ... Read more back. Water came rushing out. Luckily no damage to the motor.
5) Used pliers to remove the bottom hose clamp.
6) Put everything back together Total time <30 minutes.

Unfortunately, the water is still not completely draining. I am now looking at the hoses for obstructions. Any other suggestions?
Thanks

I unplugged the washer, put a towel down, leaned it back and held it up with one hand while undoing the clamps with plyers. Pulled the two clamps off, pulled the pump, put the new pump on, reattached the clamps. Most of this with one hand while the other held the washer at an angle.

First I watched the repair video. Then I pulled the power plug and shut the water off. I didn't have all the room available to remove the front and sides of the machine in my narrow hallway so I just slid it away from the wall and leaned it back against the wall and had plenty of room to do the repair lying on my side. $28.00 part and in ... Read more 20 minutes all done. This is the second time this site saved me time and mucho money. Thank you. Leon B. from Massachusetts