Maytag Dishwasher Switches
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Maytag Dishwasher Switches
Your Price
$47.40
In Stock
Maytag Dishwasher Overfill Control Switch
PartSelect Number PS11750031
Manufacturer Part Number WPW10195039
This part is also known as a float switch. This float switch, when activated, stops the flow of water into the dishwasher.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Dennis from AUBURNDALE, WI
water fill overflows at times
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
Read more...
Your Price
$27.36
In Stock
Maytag Dishwasher Switch
PartSelect Number PS16555330
Manufacturer Part Number W11545764
This dishwasher float switch helps monitor water levels during operation to prevent overfilling and potential leaks. When the water level reaches the correct height, the switch signals the dishwasher to stop filling and drain as needed. Replacing a faulty float switch can resolve issues such as the dishwasher not filling properly or water continuing to fill and overflow. Installation is straightforward and can be completed with basic tools.
Fixes these symptoms
- Will not fill with water
- See more...
Your Price
$72.00
In Stock
Maytag Dishwasher Door Switches And Holder Assembly
remove the four wire conections and replace with new new switch Read more...
PartSelect Number PS2099645
Manufacturer Part Number 99002254
This part senses when the dishwasher door is closed so the cycle can start, and prevents it from starting if the door is not closed. If the dishwasher will not start or will not close, you may need to replace the door switches and holder assembly, also known as the door latch assembly. The dishwasher will not start if this part is defective. It includes two switches and the holder, this part does not include the handle or screws. Tools needed are T20 torx driver, needle nose pliers, and 1/4 inch nut driver. This is a genuine OEM part that is sourced directly from the manufacturer.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Will Not Start
- See more...
Installation Instructions
Robert from Johnson, VT
no power
remove the eight screws that hold the inside door cover to gain access to the door switch. remove the four wire conections and replace with new new switch Read more...
Your Price
$31.58
In Stock
Maytag Dishwasher Door Switch
first stop, the TCO, the thermal cutoff, it's like an inline fuse. I got 120 volts going in and nothing coming out. Did an ohm check and it was open.
Found it locally and replaced it. Now I've power to the control panel but the washer still doesn't work
because the micro switch in the handle is broken and that turns out to be the original problem...
the stupid plastic handle broke the micro-switch which shorted the TCO... Read more...
PartSelect Number PS11745501
Manufacturer Part Number WP8269209
This dishwasher door switch will shut your dishwasher off when the door is opened.
Fixes these symptoms
- Door latch failure
- Will Not Start
- See more...
Installation Instructions
mike from lockport, NY
dishwasher quit halfway thru a wash cycle
first I noticed that the dishwasher wasn't making any noise. Then I saw that there were no lights on the control panel. I opened the door and found water dripping off everything... I closed the door and tried hitting every button I could see, nothing happened. I checked the breaker, it was ok, and since I did all the wiring myself, I knew that was ok too. So I pulled off the upper panel of the front door and got out the electrical schematic that came with the washer. first stop, the TCO, the thermal cutoff, it's like an inline fuse. I got 120 volts going in and nothing coming out. Did an ohm check and it was open.
Found it locally and replaced it. Now I've power to the control panel but the washer still doesn't work
because the micro switch in the handle is broken and that turns out to be the original problem...
the stupid plastic handle broke the micro-switch which shorted the TCO... Read more...
Your Price
$54.24
In Stock
Maytag Dishwasher Float Assembly
PartSelect Number PS11745483
Manufacturer Part Number WP8268895
As water is filling your dishwasher, a float rises along with it. When the float reaches a predetermined level, it shuts off the flow of water, thereby preventing a leak.
Fixes these symptoms
- Leaking
- Will not fill with water
- See more...
Installation Instructions
Michael from KANSAS CITY, MO
Pan leaked at the float/switch penetration
1. do not order or buy anything before examining the tension nut and washer. 2. Unplug the unit. 3. Open the switch box before trying to remove the float. Two types; easiest is pin based and lifts out easily. If the float catches, it likely has a headed bottom and needs an assist to lift past the stop flanges. 3. Using a standard ohmmeter, check for continuity. If it checks no need to replace. 4. Check float and assembly for abnormalities; cracks, lime deposits, etc. 5. Now decide what needs replacing. Did all my work with relative ease without pulling out the appliance. A couple sequences may need realigned.
Read more...
Your Price
$50.56
In Stock
Maytag Dishwasher Door Switch
PartSelect Number PS11751645
Manufacturer Part Number WPW10274880
This Whirlpool Dishwasher Door Switch is a crucial element of your appliance's functioning, perfectly suited for select models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dishwashers. Once your door aligns and shuts, this switch detects this and ensures a smooth start to your dishwasher's cycle. Mindfully crafted, this is an authentic, OEM part ensuring optimal fit and finishing. For safety reasons, make sure to power off your appliance before attempting to install this component; we also recommend protective gear for your hands. Remember, parts may bear identical appearances but possess subtle size and shape differences ? verify a match with your model before ordering this switch! For a flawlessly functioning dishwasher, secure your Whirlpool Dishwasher Door Switch today.
Fixes these symptoms
- Will Not Start
- See more...
Your Price
$51.61
In Stock
Maytag Dishwasher Float Assembly
PartSelect Number PS11748133
Manufacturer Part Number WPW10077871
As water is filling your dishwasher, a float rises along with it. When the float reaches a predetermined level, it shuts off the flow of water, thereby preventing a leak.
Fixes these symptoms
- Leaking
- Will not fill with water
- See more...
Installation Instructions
scott from tinley park, IL
A leak in the bottom of the dishwasher
I turned off the power at the fusebox,then removed the front lower cover using a screwdriver. I then removed the complete assembly and reversed the procedure. Quite simple, and the info on Partselect saved me 85 bucks! I put Partselect in my "favorites" for future use.
Read more...
Your Price
$92.62
In Stock
Maytag Dishwasher Float Switch Kit
PartSelect Number PS557009
Manufacturer Part Number 8193506
This dishwasher float switch kit includes all the essential components—switch, lever, seal, and standpipe—to help prevent water overflow during operation. Designed to monitor water levels inside the dishwasher, the float rises as water fills the tub and activates the switch, which then signals the water fill valve to shut off. This safety mechanism helps protect your appliance from overfilling and potential leaks. Ideal for replacing a faulty or worn-out float switch, this kit is compatible with a range of dishwasher models and installs easily with basic tools.
Fixes these symptoms
- Leaking
- Not draining
- Will not fill with water
- See more...
Installation Instructions
Robert from Rochester, NY
Dishwasher leaked under right front corner. Discovered that overflow(float switch) was either sticking allowing fill to overflow or rubber gasket was deteriorated allowing water to leak through mounting hole.
Removed mushroom shaped float cover by simply pulling up. Cover simply slide down into switch which is mounted through the floor of the tub. Using an adjustable wrench loosened and removed plastic fastening nut allowing removal of switch assembly from below. Disconnected two wires from switch and attached replacement assembly, reinserted in mounting hole, reattached nut from top, reinserted float cap and job done! The only tricky part is that the switch needs to be mounted inside assembly, wires connected and snapped shut before reinserting. Not difficult once you figure it out, Also need to make sure rubber washer is inserted on the overflow tube before reinstalling. Keep track as you remove and simply reverse the order. Tried to obtain part locally and was told it would be 6-10 days before delivery. Order from Part select arrived in 2 days.
Read more...
Your Price
$50.56
In Stock
Maytag Dishwasher Float Switch
PartSelect Number PS11745484
Manufacturer Part Number WP8268909
Water that fills your dishwasher lifts the float. When it reaches a certain level, the float triggers this float switch to shut off, thereby shutting off the flow of water into the dishwasher.
Fixes these symptoms
- Leaking
- Not draining
- Will not fill with water
- See more...
Installation Instructions
Robin from Golden, CO
dishwasher overflowed-assumed the problem was the float switch
replaced the broken parts.
Read more...
No Longer Available
Maytag Dishwasher Float Switch
Installed new float assembly, but could not use the float palnut, it had too small of a hole, I substituted a larger one that fit the float better. Note I fitted the palnut to the float (the nut cuts it's own threads in the float) before installing the float. This made installation easier. Next I transferred the two wires from the old float switch to the new float switch in the same positions as the existing switch wires. Then I installed the float switch. Finally, I cleaned up the float switch actuator and screw so that the actuator moves freely on the screw. I then installed the float switch actuator and ran the dishwasher to check for proper operation. Note: this float and switch control the water level in the dishwasher. If the actuator sticks, the dishwasher will fill with too much water and leak. If the float has collected dirt inside, it will weigh more and the water level will be too high, causing the dishwasher will fill with too much water and leak. If the switch sticks or fails the water level will be too high, causing the dishwasher will fill with too much water and leak. That is why I relaced the parts: float and switch. I don't want to go back and work on this again.
Lastly, after a few days of proper operation, I installed the two plates located below the dishwasher door. Job done! Read more...
PartSelect Number PS11747680
Manufacturer Part Number WP99002560
Water that fills your dishwasher lifts this float. When it reaches a certain level, the float triggers the float switch to shut off, thereby shutting off the flow of water into the dishwasher.
Fixes these symptoms
- Leaking
- Not draining
- Will not fill with water
- See more...
Installation Instructions
Andrew from Northfield, OH
Dishwasher leaks water
I removed the two plates located below the dishwasher door to expose the float switch. I removed the two screws holding float switch, I removed screw holding switch actuator, then I removed float assembly.Installed new float assembly, but could not use the float palnut, it had too small of a hole, I substituted a larger one that fit the float better. Note I fitted the palnut to the float (the nut cuts it's own threads in the float) before installing the float. This made installation easier. Next I transferred the two wires from the old float switch to the new float switch in the same positions as the existing switch wires. Then I installed the float switch. Finally, I cleaned up the float switch actuator and screw so that the actuator moves freely on the screw. I then installed the float switch actuator and ran the dishwasher to check for proper operation. Note: this float and switch control the water level in the dishwasher. If the actuator sticks, the dishwasher will fill with too much water and leak. If the float has collected dirt inside, it will weigh more and the water level will be too high, causing the dishwasher will fill with too much water and leak. If the switch sticks or fails the water level will be too high, causing the dishwasher will fill with too much water and leak. That is why I relaced the parts: float and switch. I don't want to go back and work on this again.
Lastly, after a few days of proper operation, I installed the two plates located below the dishwasher door. Job done! Read more...
Related Maytag Dishwasher Parts
- All Maytag Dishwasher parts
- Maytag Dishwasher Brackets and Flanges
- Maytag Dishwasher Caps and Lids
- Maytag Dishwasher Circuit Boards and Touch Pads
- Maytag Dishwasher Deflectors and Chutes
- Maytag Dishwasher Dishracks
- Maytag Dishwasher Dispensers
- Maytag Dishwasher Doors
- Maytag Dishwasher Ducts and Vents
- Maytag Dishwasher Filters
- Maytag Dishwasher Fuses
- Maytag Dishwasher Handles
- Maytag Dishwasher Hardware
- Maytag Dishwasher Hinges
- Maytag Dishwasher Hoses and Tubes
- Maytag Dishwasher Insulations
- Maytag Dishwasher Latches
- Maytag Dishwasher Lights and Bulbs
- Maytag Dishwasher Motors
- Maytag Dishwasher Panels
- Maytag Dishwasher Pumps
- Maytag Dishwasher Racks
- Maytag Dishwasher Seals and Gaskets
- Maytag Dishwasher Spray Arms
- Maytag Dishwasher Springs and Shock Absorbers
- Maytag Dishwasher Valves
- Maytag Dishwasher Wheels and Rollers
- Maytag Dishwasher Wire Plugs and Connectors