LG Dryer Parts

ROLLER ASSEMBLY

★★★★★

★★★★★

(41)

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. It is recommended that you replace both rollers at once. You may notice that this part needs to be replaced if you are experiencing a squeaking noise, which could be due to the bearing going bad. The bearing could be severely damaged if you hear a very loud thumping noise, much like you would when you are drying a pair of shoes.

Dryer Lint Filter

★★★★★

★★★★★

(131)

The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, measures around 12 inches wide by 11 inches high, and is easy to install. It slides into the lint filter slot in your dryer. If there is visible damage to the screen then it's time to replace the part. We recommend that you thoroughly clean the lint filter before every load, but even with good maintenance, this hard-working part is often damaged or worn over time. If your dryer isn't drying quickly, the filter may be responsible. The manufacturer has made an authorized substitution to the lint filter. Due to the changes, the manufacturer suggests changing the filter guide, part # MEA4905001 and filter cover, part # MCK66787901. The replacement of the entire component including the filter and surrounding area and guide simply involves the removal of a few screws and screwing the new parts back into place.

Dryer Thermistor

★★★★★

★★★★★

(4)

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shortening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

Thermal Fuse

★★★★★

★★★★★

(21)

This thermal fuse acts as a high-limit thermostat, and shuts off the heating element when the dryer overheats by cutting off power to the dryer. If the thermal fuse has blown, the dryer will not start. These fuses cannot be reset, so if yours has blown, you will need to replace it. A common reason for the thermal fuse to blow on a dryer is if the exhaust vent on your dryer is restricted or blocked. Hot air will be confined in the dryer and the fuse will trip and stop the electricity from flowing to the gas valve or heating element.

Moisture Sensor

★★★★★

★★★★★

(6)

The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough heat to dry the clothes or is taking too long to dry, this may indicate that a repair to the senor is required. To access this part, you will need to remove the front bulk head. To remove this, you will need to remove the screws securing the top. Uninstall the screws that support the control panel and lift. Remove screws holding the support bracket in place so you can detach this piece. Detach the wire harness and remove the wire, then set the bracket aside. You will now open the dryer door and release it by taking out the bottom two screws. Disconnect the wire harness and moisture sensor wire harness, remove screws from front bulk head, and remove screws that secure the duct housing. You should be able to completely remove the bulk head. You will find the sensor underneath the lint filter grill, which will also need to be removed.

Blower Thermostat

★★★★★

★★★★★

(6)

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside your dryer drum. As the air is being measured, it will turn the heat on or off in order to maintain a stable temperature within the drum. The most common reason you would need to replace your thermostat is if your dryer is not receiving enough heat, or any heat at all.The tools you will need to complete this repair include a Phillips screwdriver, and a flat-head screwdriver.

Dryer Drum Belt

★★★★★

★★★★★

(8)

The belt wraps the length of the dryer drum, secured by a tension pulley and then loops around the motor pulley. If you find that the drum is not turning properly or at all while your dryer is in succession, it might be due to the belt being broken.

Dryer Lint Filter Assembly

★★★★★

★★★★★

(76)

The lint filter sits in your dryer, and collects loose lint when the machine is operating. Sometimes the lint filter will become clogged or damaged, and in this case, you will need to replace your current lint filter with this part. The frame of this line filter is made of white plastic, and the filter is sold individually. To replace the filter, simply remove the old, damaged filter, and replace it with the new one.

Lint Screen Housing

★★★★★

★★★★★

(16)

This is an authentic dryer lint filter cover sourced directly from the manufacturer. It protects the more delicate lint filter in your dryer, so that it doesn’t get damaged and lint can’t mix in with your clothes. This product is gray in color and is made of plastic. It is sold individually. The manufacture has modified the part and suggests replacing the filter guide also. Please see your specific model information to locate the filter guide.

Dryer Lint Filter

★★★★★

★★★★★

(53)

The lint filter in your dryer is used to collect lint as it passes through the dryer vent. If you notice that your dryer is not providing enough heat, or if it takes too long to dry, you may need to replace the lint filter. You should also replace the lint filter if you notice it is damaged during regular maintenance. Many of our customers have rated this repair as easy. To complete the repair, simply remove the old lint filter and replace it with the new one. You may want to use a flat head screwdriver to remove any residual lint before you install the new filter.