LG Dryer Hardware

Your Price

$21.45

LG Dryer Clamp Assembly

★★★★★

2 Reviews

PartSelect Number PS3530864

Manufacturer Part Number ACA56078801

This is an outer seal clamp designed for use within LG washing machines. This clamp tightens and secures the gasket that seals the washer tub from the door. If your gasket is loose fitting and is not damaged or warped, this clamp is likely worn out and in need of replacing. This clamp is an OEM part and is made entirely of metal, with a strong tension spring in the middle. This outer seal clamp is sold individually and will require a set of pliers to replace.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Randy from PETERSBURG, WV

Old smelly boot seal ... 10 years old, bottom drain in boot plugged with dog hair.

Followed instructions in this youtube video:

https://www.youtube.com/watch?v=xp5sV_1SSKw

Step by step instructions were clear and concise. Easy job. Saved hundreds by not having a repair person come to the house. Read more...

Your Price

$15.00

LG Dryer Clamp

PartSelect Number PS3524032

Manufacturer Part Number 4861FR3068A

Fixes these symptoms

Leaking
See more...

Installation Instructions

Darryl E from ALICE, TX

washing machine was leaking at bottom of door and on left side from the dispenser asm. bellow was replaced & door hinge was bad

watched the video provided on site, very helpful for bellow replacement. there was no door hinge video. ordering parts for the bellow replacement, one clamp was on one page of the manual and the other clamp was on the other page, so look at the manuals provided so you can get the right part. the bellow i ordered was suppose to be for the model i have. the part ordered had a drain on the bottom, my bellow did not have a drain so i bought a brass plug, some RTV and a small clamp and fitted the RTV to the plug and installed and fitted the small clamp. All works fine. they do have a part number without the drain at the bottom and would be helpful if the user manual for the model had the exact replacement part number listed, I.E. if customer has a model number it is confirmed or not if that model number has a drain port. i was going to send 2 of the 4 extra clamps for hoses i ordered and clamp for the bellow that was wrong back for credit. i was told i could dispose of the items when i requested a shipping label and i was credited the amount + a $10 nuisance rebate. This Business IMO has exemplary customer service and with my experience i would recommend them Read more...

Your Price

$21.45

LG Dryer Locking Pin

★★★★★

2 Reviews

PartSelect Number PS3523451

Manufacturer Part Number 4774FR3118B

This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in color, and made entirely of plastic. This part is used to hold the shock absorber on the washing machine. There is a pin used at the bottom and top of the shock absorber. This model is sold individually. If your washing machine is experiencing an above-average amount of shaking and moving this part may be the reason.

Installation Instructions

Todd from STOCKTON, KS

Bearing seal out causing bearings to get wet and very noisy

Watched a short video to figure out to remove panels. After panels were off I removed as much as I could from the inside of the machine. This was not completely necessary however for an extra half hour it made inspection, cleanup and removal of tub housing out the front of the machine much easier. Once out, I split the two halves of the outer basin and sprayed the spider shaft with penetrating oil. Using a brass drift I did have to get a bit aggressive to drive spider shaft out, then I used a heavy metal punch to hammer out the bearings. For those who may not know using brass or a soft metal will keep from damaging reusable parts. At this point it was cleanup time, with dish soap I scrubbed the two halves of the outer basin and the wash basin itself then used emery cloth on the bearing casing and spider shaft. I am a firm believer if u take the time to cleanup properly things go back together much easier. At this point I began to reassemble, replacing tub bearings and seal, the wash basin then putting the two halves of the outer basin back together. I strongly recommend replacing gasket for the halves of the outer basin, for as much as it takes to get there it is money well spent to up the chances of a leak free system. Now with the wash tub back together it was time to reset the tub and hook everything back up. I skipped a lot of steps but if a person pays attention, takes pictures if they have to, even numbers lines with a sharpie it is a very easy repair. Very easy but very time consuming. I am DIY’er, in all I spent about ten hours over two days to do this job. Thus being said I am very particular spent a lot of time cleaning, scrubbing looking at as many wear points and checking for rubbed wires. Hope this helps someone out there, definitely not a strong writer or like doing it. Oh one other thing, I ordered the shocks on the bottom side of wash tub just because I guess not thinking they were bad just thinking I could help tune it up. Was surprised to find the old ones were completely shot, was glad I ordered new ones. After repairs, noise is gone and machine is quiet again. Thank you, your website is very easy to find parts and order. Read more...

Your Price

$15.00

LG Dryer Holder

★★★★★

1 Review

PartSelect Number PS3524224

Manufacturer Part Number 4930FR3040A

Installation Instructions

Todd from LAKEWOOD, CO

Drum spring broke

Removed top panal found broken parts and pieces, replaced spring and plastic spring holder. Straightened out and reattached drum front boot. Read more...