EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

Kenmore Ice Maker Parts

Popular Kenmore Ice Maker Parts

Keep ice production in step with available bin space using this ice maker bin thermistor. The probe senses temperature changes as ice accumulates around it and sends that information to the control board, allowing production to pause when the bin is full. A failed sensor may cause overflowing, early shutdowns, or interrupted ice production. Replacing a faulty thermistor helps restore accurate temperature feedback. Disconnect appliance power before installation, handle the probe and wiring gently, and secure the sensor in its original mounting position This is an OEM part sourced directly from the manufacturer.
Keep ice production in step with available bin space using this ice maker bin thermistor. The probe senses temperature changes as ice accumulates around it and sends that information to the control board, allowing production to pause when the bin is full. A failed sensor may cause overflowing, early shutdowns, or interrupted ice production. Replacing a faulty thermistor helps restore accurate temperature feedback. Disconnect appliance power before installation, handle the probe and wiring gently, and secure the sensor in its original mounting position This is an OEM part sourced directly from the manufacturer.
Installation Instructions
Travis from N CHESTERFLD, VA
Ice bin overfilling
I'm an hvac/r technician, and regularly work on ice machines. Begin my pulling the white over beneath the control panel. It snaps in place so pull on the bottom then left out. 1/4 nut driver is all you need, and remove the screw holding the bin thermistor clip to the side. Up to the right , beneath the control panel, behind the plastic panel you previously removed is the mollex connector. Unplug the thermistor and follow instructions in reverse to reinstall.
This condenser fan motor kit includes a motor, fan blade, wire harness, and screws. Used in a refrigerator, the condenser fan motor moves the condenser fan blade to direct and move air across the condenser coil. Please note: The manufacturer has changed the appearance of the product from the original. The kit still functions the same as the original part. It is an OEM factory replacement. Make sure to unplug the refrigerator from the power source and wear gloves to protect your hands. Also, a helpful tip is to store food to prevent deterioration when the power is off.
This condenser fan motor kit includes a motor, fan blade, wire harness, and screws. Used in a refrigerator, the condenser fan motor moves the condenser fan blade to direct and move air across the condenser coil. Please note: The manufacturer has changed the appearance of the product from the original. The kit still functions the same as the original part. It is an OEM factory replacement. Make sure to unplug the refrigerator from the power source and wear gloves to protect your hands. Also, a helpful tip is to store food to prevent deterioration when the power is off.
What this part fixes:
  • Clicking sound
  • Freezer section too warm
  • Fridge and Freezer are too warm
Installation Instructions
Josue from Jacksonville, NC
Seven year old condenser fan was making noise when it was running.
The process to repair was very simple, I removed the back of the refrigerator to expose the motor area. I then removed three screws that held the condenser motor in place. once it was loose I detactched the electrical harness and removed the old motor. I then placed the new motor in place and secured it with the screws and reattached the new electrical harness that came with the new part. Once completed I reviewed it to make sure I didn't miss anything. I then replaced the cover over the motor area and enjoyed my success in repairing my own appliance with no added cost for labor, which would have been expensive I'm sure. The part purchased came with clear and consice instructions very easy to follow.
This genuine OEM replacement part is a water filter for your fridge or freestanding ice maker. The filter is used to remove contaminants and particles from the water, to ensure a clean and fresh taste. The filter should be replaced every six to nine months, or after 2000 gallons of water have passed through, whichever occurs first.
This genuine OEM replacement part is a water filter for your fridge or freestanding ice maker. The filter is used to remove contaminants and particles from the water, to ensure a clean and fresh taste. The filter should be replaced every six to nine months, or after 2000 gallons of water have passed through, whichever occurs first.
For an ice maker to form ice, water circulates over the evaporator plate. This OEM recirculating pump moves that water and is rated at 12 V, 60 Hz, and 13 W. Check your appliances model number to confirm compatibility. Disconnect power and wear work gloves before installation.
For an ice maker to form ice, water circulates over the evaporator plate. This OEM recirculating pump moves that water and is rated at 12 V, 60 Hz, and 13 W. Check your appliances model number to confirm compatibility. Disconnect power and wear work gloves before installation.
Installation Instructions
Richard from North Wilkesboro, NC
was not making ice
diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well
Water moves through the appliance system via this recirculating pump assembly, which includes a sensor. This is an OEM part.
Water moves through the appliance system via this recirculating pump assembly, which includes a sensor. This is an OEM part.
Original Equipment Manufacturer

MAKE THIS REPAIR A GUARANTEED WIN

OVER 2 MILLION PARTS TO ENSURE VICTORY

The ice maker uses this OEM drain pump to remove water from its reservoir during flushing. It is rated 12V AC, 13W, and 60Hz. Check compatibility using the appliance model number. Disconnect power before installation and wear work gloves.
The ice maker uses this OEM drain pump to remove water from its reservoir during flushing. It is rated 12V AC, 13W, and 60Hz. Check compatibility using the appliance model number. Disconnect power before installation and wear work gloves.
Installation Instructions
Jonathan from WILLIAMSBURG, VA
Water not refilling after initial batch of ice
The water filled on startup (actually over-filled, which was a clue). After that water was used to make ice, no new water came in so the recirculation pump just made whining noises in the mostly empty reservoir. Since water could come in (on start up) I reasoned it wasn't the water inlet valve, and everything else suggested the ice maker was getting inaccurate info about how much water was in the reservoir. Turns out, the water recirculation pump has a water level sensor built in. So while the pump itself still functioned, the water level sensor inside had gone bad. Replacing the pump fixed the issue. There are videos online that show how to accomplish that, but it was pretty straight-forward. The dis-assembly was sometimes irritating because it's hard to see and maneuver around inside. It'll help if you put the machine closer to eye level. Pay close attention to videos that show the disassembly because there are a couple of tabs that are hard to find.
If your refrigerators interior light is not working, the door light switch may be the part to replace. It activates the light as the door opens or closes and has two push-on wire connections. Unplug the refrigerator before installation, and confirm fit using your refrigerators model number. This is an OEM part.
If your refrigerators interior light is not working, the door light switch may be the part to replace. It activates the light as the door opens or closes and has two push-on wire connections. Unplug the refrigerator before installation, and confirm fit using your refrigerators model number. This is an OEM part.
What this part fixes:
  • Light not working
Installation Instructions
Fred from Oceanport, NJ
Door switch module wore out
Pull out old module...
Remove 2 wires...
Tape to inside wall [don't want them to fall down into side panel]..

Order new switch..

Fed Ex pkg came on 2nd day..

Install wires on switch...
Press into opening...
Check door light on..[OK]
.. Done
The 1-inch squares on this 15-inch OEM cutting grid cut an ice slab into cubes. It is for a freestanding ice maker, so confirm compatibility with your appliance model. Disconnect power before installation, wear work gloves, and reconnect the cutter-grid harness correctly.
The 1-inch squares on this 15-inch OEM cutting grid cut an ice slab into cubes. It is for a freestanding ice maker, so confirm compatibility with your appliance model. Disconnect power before installation, wear work gloves, and reconnect the cutter-grid harness correctly.
Installation Instructions
Brad from Bakersfield, CA
Grid Assembly had a broken wire and would not separate the ice sheets into cubes
I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I had ice cubes within a couple of hours
Before water reaches the evaporator plate, the ice maker holds it in this white plastic pan. Confirm fit with your appliances model number; this is an OEM replacement.
Before water reaches the evaporator plate, the ice maker holds it in this white plastic pan. Confirm fit with your appliances model number; this is an OEM replacement.
Control water filling with this ice maker water inlet valve assembly. Its electric coil opens the valve when water is needed and closes it to stop the flow between fills. Quick-connect fittings hold the water lines securely at the valve. A worn or damaged assembly may cause slow filling, reduced ice production, unwanted dripping, or leaks around the housing. Replacing a faulty valve helps restore proper water delivery and shutoff. Unplug the appliance and turn off the water supply before disconnecting tubing or wiring. This is an OEM part sourced directly from the manufacturer.
Control water filling with this ice maker water inlet valve assembly. Its electric coil opens the valve when water is needed and closes it to stop the flow between fills. Quick-connect fittings hold the water lines securely at the valve. A worn or damaged assembly may cause slow filling, reduced ice production, unwanted dripping, or leaks around the housing. Replacing a faulty valve helps restore proper water delivery and shutoff. Unplug the appliance and turn off the water supply before disconnecting tubing or wiring. This is an OEM part sourced directly from the manufacturer.
Installation Instructions
william from etowah, TN
Ice maker started leaking water from the water valve that inputs water to the appliance.
removed the front cover below the compartment door,removed the 2 screws holding the valve to the case and removed the water lines from the valve.The process was reversed to install the new valve.

Kenmore Ice Maker Model Types

Select the appliance you're up against.