EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

10689583700 Kenmore Ice Maker - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water Tube Kit – Part Number: W10823511
$27.36
In Stock
Water Tube Kit
★★★★★
★★★★★
(8)
Part #W10823511
This is the replacement water tube kit for your refrigerator. This tubing is made of plastic, is 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube, and may need to be cut. This water tube transports water to the ice and water dispensers. If your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Complete Ice Cutter Grid Assembly – Part Number: WP2313637
$163.15
In Stock
Complete Ice Cutter Grid Assembly
★★★★★
★★★★★
(14)
Part #WP2313637
The 1-inch squares on this 15-inch OEM cutting grid cut an ice slab into cubes. It is for a freestanding ice maker, so confirm compatibility with your appliance model. Disconnect power before installation, wear work gloves, and reconnect the cutter-grid harness correctly.
Ice Cutting Grid Wire – Part Number: 4387020
$49.50
In Stock
Ice Cutting Grid Wire
★★★★★
★★★★★
(7)
Part #4387020
This ice cutting grid wire separates sheets of ice into cubes in compatible ice makers. The kit contains approximately 10 feet of wire and eight mounting screws. Two kits are needed to replace the wires running in both directions of the grid. A broken wire may leave an ice sheet sitting on the grid without being cut into cubes. Inspect the wire and check the grid harness connection when this happens, since a loose connection can cause similar problems. Follow the kit instructions for fitting and securing the replacement wire. This is an OEM part sourced directly from the manufacturer.
Ice Maker Water Inlet Valve – Part Number: WPW10217917
$170.41
In Stock
Ice Maker Water Inlet Valve
★★★★★
★★★★★
(3)
Part #WPW10217917
Controlled water filling starts with this ice maker water inlet valve, which opens when it receives an electrical signal and closes when filling is complete. It regulates incoming water so the appliance has the supply needed for ice production. A restricted passage, failed solenoid, or damaged valve body may cause incomplete fills, reduced ice output, or leaks. Replacing a faulty valve helps restore proper water intake. Disconnect power and shut off the water supply before installation, then check all connections for leaks after restoring water pressure. This is an OEM part sourced directly from the manufacturer.
Ice Maker Pump – Part Number: W11566407
$75.04
In Stock
Ice Maker Pump
★★★★★
★★★★★
(3)
Part #W11566407
During flushing, an ice makers reservoir drain pump removes water from the reservoir. This OEM part has a multi-pin electrical connector. Confirm fit against your ice makers model and disconnect power before installation.
Ice Maker Drain Fastener Cap – Part Number: WP2185696
$34.74
In Stock
Ice Maker Drain Fastener Cap
★★★★★
★★★★★
(4)
Part #WP2185696
This is a drain fastener cap and is used in conjunction with your freezer/refrigerator. This model is almost 1.5 inches in diameter, half an inch thick, and is white in color. This piece will fasten to the bottom of the water pan in your ice maker. It keeps the water in the water pan from leaking into your appliance. If your drain cap is loose or broken, the liquid from the water pan will empty and you will have no ice or very thin ice. Make sure when replacing this part to secure the drain cap tightly.
Ice Maker Water Distributor Tube – Part Number: W10863947
$51.61
In Stock
Ice Maker Water Distributor Tube
★★★★★
★★★★★
(1)
Part #W10863947
The water distributor tube distributes water from the reservoir to the evaporator plate.
Water Bucket – Part Number: WP2324334
$74.95
In Stock
Water Bucket
★★★★★
★★★★★
(1)
Part #WP2324334
This water bucket provides contained storage for collected water or ice within the appliance. Its durable construction supports regular removal and cleaning. Replacing a cracked or damaged bucket helps prevent leaks and maintain proper operation.
Ice Maker Screw – Part Number: WP3400884
$7.47
Special Order
Ice Maker Screw
Part #WP3400884
Screw size is 8-18 x 5/8". Used with stand-alone ice cube makers.
Screw – Part Number: WP489443
$7.47
In Stock
Screw
Part #WP489443
This screw is sold individually.
Reservoir Hose – Part Number: WP2185626
$55.29
On Order
Reservoir Hose
Part #WP2185626
Front or Rear Spacer/Bracket – Part Number: 8201790
$48.45
Special Order
Front or Rear Spacer/Bracket
★★★★★
★★★★★
(1)
Part #8201790
Note: Sold individually. Used with stand-alone ice cube makers.

Questions And Answers for 10689583700

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Paul - For model number 10689583700
February 25, 2020
My ice maker does not shut off when full, just keeps making ice. How can I fix this.
Chris Boyle Profile
Hello Paul, Thank you for the question. We suggest testing the Temperature Sensor, PartSelect Number PS11756166. You will find this part located in the water pump area of the ice cube maker. The function of this part is to determine the water level within the water reservoir. Once the water level reaches a certain point, the sensor will signal the controls to fill the reservoir. We hope this helps.
No Longer Available
Temperature Sensor
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the 10689583700

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Grid Assembly had a broken wire and would not separate the ice sheets into cubes
33 of 37 people found this instruction helpful.
  • Brad from Bakersfield, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver
I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I ha d ice cubes within a couple of hours
Was this helpful?
Thank you for voting!
the top wire on the cutting grid broke and thus no longer cut the ice. It sat on the wire until the ice melted, depositing no ice into the bin
25 of 26 people found this instruction helpful.
  • Sherri from Ada, OK
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers
I removed the cutter grid and unplugged the light bulb and wire heating plug ins. I slid the front cover plate off the cutting grid and loosened the screws on the front of the cutter grid and unthreaded the broken, top grid wire, leaving the bottom wire in place as it was in tact.
I then threaded the new wire through the cutting gri d frame starting in the center and threading right and then left. While the threading was not difficult, the wire was easily kinked. The process up to this point was only 15 minutes or so.

Once it was completely threaded, I worked for a couple of hours trying to smooth and straighten the wire so that is was somewhat taut and straight enough to create symetrical ice cubes.
My frustration came in pulling on the wire from the center point to each outside ending point where it was to be wrapped around the screw and the screw tightened back down. The wire was fragile enough that it would break, by the time I was finished I barely had enough wire left to touch the screw let alone hook around the screw.
After 3 or four days of successful opperation, the grid quit cutting again. As I took it apart, it was obvious that the weight of the ice was enough to pull the wire, that was already too short, away from the screw. I refastened it again, but think it is unlikely to hold.
If it won't hold, I would be hard pressed to purchase another wire. I may bite the bullet and purchase the entire grid mechanism with the wires already installed. Even though the cost of the entire grid mechanism is $200 more than the purchase of another wire, it may well be worth the ease of installation!
Was this helpful?
Thank you for voting!
Water began to leak under the refrigerator. Source looked like it was coming from control valve suppling water to ice maker and water dispenser.
21 of 32 people found this instruction helpful.
  • jesse from hacienda heights, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.
Was this helpful?
Thank you for voting!