My Orders
Jenn-Air Cooktop Igniters
GET YOUR OFFICIAL Jenn-Air PARTS TO ENSURE VICTORY
Popular Jenn-Air Cooktop Igniters
This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will need a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions.
This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will need a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions.
What this part fixes:
- Element will not heat
- Gas igniter glows, but will not light
- Will Not Start
Installation Instructions
roy from East Providence, RI
gas burner ignitor failure
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed t
... Read more
hat rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Read less
This is a burner electrode for your oven, range, or stove. This part has a male spade. It helps your burner ignite by creating a spark, producing a flame, and lighting the surface burner. If your burner will not heat properly, you may have to replace the burner electrode. Your electrode is located under your burner. This is an OEM replacement part that will be sourced from the genuine manufacturer. This part measures less than 1.5 inches long. It is sold individually. If you need a wire lead to complete your repair, you can purchase them locally.
This is a burner electrode for your oven, range, or stove. This part has a male spade. It helps your burner ignite by creating a spark, producing a flame, and lighting the surface burner. If your burner will not heat properly, you may have to replace the burner electrode. Your electrode is located under your burner. This is an OEM replacement part that will be sourced from the genuine manufacturer. This part measures less than 1.5 inches long. It is sold individually. If you need a wire lead to complete your repair, you can purchase them locally.
What this part fixes:
- Element will not heat
- Gas igniter glows, but will not light
- Will Not Start
Installation Instructions
Dennis from Iredell, TX
Simple to change, but you do need a torx bit screwdriver.
Remove screws holding burner down, invert and remove screw in igniter. Reverse to reinstall.
Is your oven not cooling like it used to? You might need a new blower, a crucial component that circulates air to safeguard controls, wiring, and other parts from overheating. We understand how important it is to keep your oven in top shape, and that's where the genuine OEM Whirlpool Blower comes in. Specially designed for wall oven installations, it helps bring your oven back to peak performance, ensuring effective and efficient cooling. This blower isn?t just for Whirlpool appliances?it's the perfect match for a wide array of models from KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef too. But remember, ovens can have subtle differences, so it's a good idea to match the part to your model's specifications. This way, you can be confident it?s the perfect fit for your oven's needs. Installing your new blower requires a little care. Please disconnect the power first because safety should always come first. And don?t forget to wear work gloves to protect your hands. So, ready for your oven to cool like it's brand new again? Choose the genuine OEM Whirlpool Blower, the key to maintaining a safe, balanced temperature within your oven while extending its longevity.
Is your oven not cooling like it used to? You might need a new blower, a crucial component that circulates air to safeguard controls, wiring, and other parts from overheating. We understand how important it is to keep your oven in top shape, and that's where the genuine OEM Whirlpool Blower comes in. Specially designed for wall oven installations, it helps bring your oven back to peak performance, ensuring effective and efficient cooling. This blower isn?t just for Whirlpool appliances?it's the perfect match for a wide array of models from KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef too. But remember, ovens can have subtle differences, so it's a good idea to match the part to your model's specifications. This way, you can be confident it?s the perfect fit for your oven's needs. Installing your new blower requires a little care. Please disconnect the power first because safety should always come first. And don?t forget to wear work gloves to protect your hands. So, ready for your oven to cool like it's brand new again? Choose the genuine OEM Whirlpool Blower, the key to maintaining a safe, balanced temperature within your oven while extending its longevity.
What this part fixes:
- Element will not heat
- Gas igniter glows, but will not light
- Will Not Start
Installation Instructions
Daniel from Needham, MA
spark igniter was weak and not lighting the flame.
Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel an
... Read more
d remove the 3 wires connecting the top burner assembly and also remove the 2 gas lines. Now you will be able to remove the burner assembly safely. Flip it over and try to unscrew the screw holding the igniter. When you fail, drill it out and get a small metal screw to replace it. The metal is soft and the screw is hard, so drill carefully. The rest is easy, put in the new igniter and screw. and put it back together.
Read less
This part provides the spark to the burners.
This part provides the spark to the burners.
Installation Instructions
Patricia from Overland park, KS
Spark igniter out
The primary spark igniters failed. Take the (small) screws out of the sides and bottom of the pan. The front of the pan must be removed from the bottom, because the front burner igniter wire is too short to allow reassembly once attached. Only other is the screws for the attachment bracket are larger than the holes. Suggest routing them o
... Read more
ut slightly to get them to grip the screws. Otherwise it is quite simple. Pull the connections with a needlenose and press the new wire connection back on firmly. Screw the screws back in the pan.
Read less
This surface igniter provides reliable ignition by generating the heat needed to light the burner safely and efficiently. Proper ignition improves cooking performance and safety. Replacing a worn igniter restores fast, consistent burner operation.
This surface igniter provides reliable ignition by generating the heat needed to light the burner safely and efficiently. Proper ignition improves cooking performance and safety. Replacing a worn igniter restores fast, consistent burner operation.
Installation Instructions
Ronald from ROSEVILLE, CA
Surface ignitor not working on one burner
Disconnect power and turn off gas. Remove all grills, knobs and burners. Under the burners are 2 Phillips head screws. Remove all 10 screws. Remove surface plate. Remove the one igniter with problem. There is a small metal clip holding it in place. Remove the wire. Install new ignitor and reverse all steps above.
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This part creates the spark that lights the gas and starts the burners.
This part creates the spark that lights the gas and starts the burners.
Installation Instructions
Bill from Pearland, TX
would not stop igniting even after fire was on
unplugged unit from wall, disconnected gas line, and untaped the vent. disconnect the control knobs and unplugged and removed the control unit from the main unit. pulled the main unit out from the countertop and set it on a table. disconnect the burners and spark iginiters from the main unit. undo screws holding chrome brackets and stove
... Read more
base, to access iginiter. disconnect wiring from igniter and the one screw, replace iginiter. reverse everything to re-install
Read less
The surface igniter creates the spark needed to light the gas burners on a range, ensuring quick and reliable ignition during everyday cooking. When the original igniter becomes weak, slow to spark, or fails to light the burner at all, replacing it restores smooth, consistent flame ignition. Designed for select gas cooktops and ranges, this igniter offers a straightforward fix for common “won’t-light” burner issues and helps keep the appliance operating safely and efficiently.
The surface igniter creates the spark needed to light the gas burners on a range, ensuring quick and reliable ignition during everyday cooking. When the original igniter becomes weak, slow to spark, or fails to light the burner at all, replacing it restores smooth, consistent flame ignition. Designed for select gas cooktops and ranges, this igniter offers a straightforward fix for common “won’t-light” burner issues and helps keep the appliance operating safely and efficiently.
ELECTRODE (CR)
ELECTRODE (CR)
Having trouble with your washing machine? The GE Drive Pulley could be exactly what it needs to get back at its top performance. This simple yet essential part links to your washing machine?s drive belt. Its job? Helping to smoothly turn the spin basket drive shaft and contribute to efficient wash cycles. Whether it's due to normal wear and tear, or an unexpected malfunction, replacing this component can restore your washing machine's reliability and prolong its life. Remember, always disconnect your machine from the power source before starting any repair - safety first. This GE Drive Pulley is part of GE?s commitment to ensuring your appliances maintain their best possible performance, enhancing their longevity. Put on your work gloves and get your washing machine back in action with this key part. Trust in GE for quality components that keep your appliances working their best.
Having trouble with your washing machine? The GE Drive Pulley could be exactly what it needs to get back at its top performance. This simple yet essential part links to your washing machine?s drive belt. Its job? Helping to smoothly turn the spin basket drive shaft and contribute to efficient wash cycles. Whether it's due to normal wear and tear, or an unexpected malfunction, replacing this component can restore your washing machine's reliability and prolong its life. Remember, always disconnect your machine from the power source before starting any repair - safety first. This GE Drive Pulley is part of GE?s commitment to ensuring your appliances maintain their best possible performance, enhancing their longevity. Put on your work gloves and get your washing machine back in action with this key part. Trust in GE for quality components that keep your appliances working their best.