My Orders
Crosley Dryer Switches
GET YOUR OFFICIAL Crosley PARTS TO ENSURE VICTORY
Popular Crosley Dryer Switches
This dryer door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open, and operates the drum light. White in color and 6.5 inches long, this OEM switch is comprised of plastic and metal, and features the switch and three wires that comprise the part. Sold individually, this part attaches to the inside of the top end of the front panel. One end attaches to the wiring harness, the other goes through the panel to make contact with the door when the door is closed. Over time, this part can be subject to material fatigue or breakage due to frequent use or rough handling. If it breaks or is defective, you won't be able to start or stop your drying cycle, depending on the position your switch broke in. The easiest way to test this part for functionality is to test it by hand. Push on the black tab that sticks out of the front panel to make contact with your dryer door; if there is no resistance in the tab and it doesn't make a click sound, you may need to replace it.
This dryer door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open, and operates the drum light. White in color and 6.5 inches long, this OEM switch is comprised of plastic and metal, and features the switch and three wires that comprise the part. Sold individually, this part attaches to the inside of the top end of the front panel. One end attaches to the wiring harness, the other goes through the panel to make contact with the door when the door is closed. Over time, this part can be subject to material fatigue or breakage due to frequent use or rough handling. If it breaks or is defective, you won't be able to start or stop your drying cycle, depending on the position your switch broke in. The easiest way to test this part for functionality is to test it by hand. Push on the black tab that sticks out of the front panel to make contact with your dryer door; if there is no resistance in the tab and it doesn't make a click sound, you may need to replace it.
Installation Instructions
pat from lisbon,, OH
door switch was bad
i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service
This switch or push to start switch is used for dryers. It is the tool that completes the circuit and ultimately starts the dryer by pressing and releasing the button after selecting a setting on the timer. The tools needed for this project are a 1/4 inch nut driver, and a flathead screwdriver. To repair, first remove the rear panel and start switch. Next, replace with new start switch and rear panel. Remember to unplug your dryer before beginning this installation and refer to the manual provided by the manufacturer for further installation instructions.
This switch or push to start switch is used for dryers. It is the tool that completes the circuit and ultimately starts the dryer by pressing and releasing the button after selecting a setting on the timer. The tools needed for this project are a 1/4 inch nut driver, and a flathead screwdriver. To repair, first remove the rear panel and start switch. Next, replace with new start switch and rear panel. Remember to unplug your dryer before beginning this installation and refer to the manual provided by the manufacturer for further installation instructions.
Installation Instructions
Josh from Emory, TX
Push to Start switch burned out due to electrical problem
Unplug from the wall ,remove upper back panel ( watch out for the grounding wire screwed to the panel), pulled off front knob, then twist and pull the switch out. Unplug the burned out switch, plugged in the new one. Re-assembled what I took apart, plugged her up and dried the load that was in the washer. Note: if yours is burned out due
... Read more
to house power surge make sure the timer is working after you replace the switch, you might need one of thoes too.
Read less
This push-to-start switch activates the dryer when the button is pressed and released. If your switch is not turning on or off, will not start, or the contacts inside the switch are shorted out, it is best to replace this part as a possible solution. Remember to unplug your appliance before beginning the installation process, as safety precaution. For installation instructions and accurate guidance, refer to the diagram provided by the manufacturer.
This push-to-start switch activates the dryer when the button is pressed and released. If your switch is not turning on or off, will not start, or the contacts inside the switch are shorted out, it is best to replace this part as a possible solution. Remember to unplug your appliance before beginning the installation process, as safety precaution. For installation instructions and accurate guidance, refer to the diagram provided by the manufacturer.
Installation Instructions
Dennis from Port Orchard, WA
Broke start switch while moving
Turned off the power.Pulled the dryer out, removed the screws from the control cover panel, unplugged the switch, pressed the release clip the did the opposite to install new switch. Replaced the back panel, put the nob on and it looks as good as new.Turned on the power.
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.
Installation Instructions
John from Bethesda, MD
Dryer would stay on after opening the Door. The switch that turns off the dryer when you open the door was not broken.
You open up the lint filter access door and remove the two small screws that hold it to the top of the dryer. Once they are removed, you insert a flat blade screwdriver under front-top of the unit and the top will pop off. Exerting a little pressure towards you will help lift to top off the mounts. There are no other screws to remove.
... Read more
The new switch comes attached to a clip. You just pull off the old clip and replace it with the new one and discard the old switch.
The new switch comes attached to a clip. You just pull off the old clip and replace it with the new one and discard the old switch.
Read less
This is a door switch that is compatible with models of dryers. The door switch in a dryer is designed to communicate with the control board when the door is open or closed. If this door switch is damaged or not working properly, it will cause your dryer to incorrectly detect whether the door is closed and will normally result in your dryer not being able to start or stopping a cycle randomly. This door switch is made entirely of plastic with the door switch tab on one end, and its wire harness on the other. Replacing this door switch is easy but does require some slight disassembly of your dryer, which you will need a screwdriver and wrench for. This door switch is an OEM part and does not come with its necessary securing screws.
This is a door switch that is compatible with models of dryers. The door switch in a dryer is designed to communicate with the control board when the door is open or closed. If this door switch is damaged or not working properly, it will cause your dryer to incorrectly detect whether the door is closed and will normally result in your dryer not being able to start or stopping a cycle randomly. This door switch is made entirely of plastic with the door switch tab on one end, and its wire harness on the other. Replacing this door switch is easy but does require some slight disassembly of your dryer, which you will need a screwdriver and wrench for. This door switch is an OEM part and does not come with its necessary securing screws.
Installation Instructions
Ronald from LANCASTER, CA
A piece of cloting snagged and broke the door switch.
Repair job took less than 10 minutes: 1) Unplug Dryer 2) Remove Lint screen and 2 Phillip screws 3) use flat putty knife to depress lid latches while lifting (latches located approx 2 - 3 inches from each side. 4) unplug defective door switch 5) remove 2 Phillip screws that secure the door switch. Reinstall switch repeating the above step
... Read more
s in reverse order and your done.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble, replacing the door switch can solve this appliance problem. The tools needed for replacement are a screw driver and wire strippers. Make sure to attach the two wires to the right two poles of the new switch, to do this you can check the resistance of the switch. Unplug the dryer before installing this part, also refer to the diagram provided by the manufacturer.
This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble, replacing the door switch can solve this appliance problem. The tools needed for replacement are a screw driver and wire strippers. Make sure to attach the two wires to the right two poles of the new switch, to do this you can check the resistance of the switch. Unplug the dryer before installing this part, also refer to the diagram provided by the manufacturer.
Installation Instructions
Don from Jacksonville, FL
Switch sticking in on position
FIRST unplug dryer from electrical source, CAUTION, the top of this dryer does not open with clips, do not pry on top to open! On the front of the dryer look under the lower panel, and find two screws, one on the left side, and one on the right, remove these screws, and pull slightly down on panel to remove. Behind this panel find two s
... Read more
crews holding the door panel, one on the left, and one on the right, remove the left, and support the door panel while removing the right side. Gently pull the bottom of door panel outward, and the clips on top of door panel will unhinge from top, carefully rotate left side of door panel to floor, and note the wire connections on switch, and orientation of switch, then unplug wires, and move door panel to a comfortable working positon. Door must be open to remove switch, then depress the two plastic retaining keepers on each side of switch, and push switch through toward door. Replace with new switch, reconnect the wires, and reassymble in reverse order. Remember, door assymbly must be inserted in dryer top at an angle, and then bottom rotated downward, and bottom panel nylon guildes inserted into door panel bottom.
Read less
This part is used to start the dryer once you have selected a setting on the timer.
This part is used to start the dryer once you have selected a setting on the timer.
Installation Instructions
ERNEST from SPRINGFIELD, MA
dryer start switch shaft was broken by using pliers after knob was lost
I first disconnected the power by unplugging power cord.
I then removed back cover from control panel using philips screwdriver.
I removed the start switch by twisting it counter clockwise.
I removed the two push on connectors from the start switch.
I installed the two connectors on the new swi ... Read more tch.
I twisted the new switch into place, and installed the new knob.
I reinstalled the back cover plate.
I inserted the power cord back into the receptacle.
I twisted the start knob clockwise.
VOILA!!!!!
I then removed back cover from control panel using philips screwdriver.
I removed the start switch by twisting it counter clockwise.
I removed the two push on connectors from the start switch.
I installed the two connectors on the new swi ... Read more tch.
I twisted the new switch into place, and installed the new knob.
I reinstalled the back cover plate.
I inserted the power cord back into the receptacle.
I twisted the start knob clockwise.
VOILA!!!!!
Read less
Discover the quality and reliability of the Whirlpool Push-to-Start Switch. This genuine OEM part is designed to work seamlessly with certain models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef clothes dryers. Serving as a crucial element, this switch triggers your dryer to start when you press and release the button, making the operation convenient and easy. Remember to disconnect the power before installing this part, and consider using work gloves to protect your hands. Please ensure the part number is correct for your model before finalizing your purchase as variations in size and shape can occur. Embellish your appliance with this essential Whirlpool Push-to-Start Switch and enjoy an improved laundry experience.
Discover the quality and reliability of the Whirlpool Push-to-Start Switch. This genuine OEM part is designed to work seamlessly with certain models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef clothes dryers. Serving as a crucial element, this switch triggers your dryer to start when you press and release the button, making the operation convenient and easy. Remember to disconnect the power before installing this part, and consider using work gloves to protect your hands. Please ensure the part number is correct for your model before finalizing your purchase as variations in size and shape can occur. Embellish your appliance with this essential Whirlpool Push-to-Start Switch and enjoy an improved laundry experience.
Installation Instructions
Diane from HGHTN LK HTS, MI
Thought it wad the start switch $23.00
Paid an extra over night fee Friday $24.00 didn't get it until Tuesday afternoon all in all it cost $51.00 then that wasn't the problem.
This part is used to start the dryer once you have selected a setting on the timer.
This part is used to start the dryer once you have selected a setting on the timer.
Installation Instructions
Vincent from Pipersville, PA
defective switch
unplug dryer
pull off switch knob
remove two screws at corners of control unit
pull unit toward you to remove
flip over and remove panel
unscrew switch then twist switch to remove from face on control unit
holding new switch next to old, remove wires from old switch and insert onto new switch
place new ... Read more switch on control unit face and twist into position
Install screws
replace panel, flip back over
position control unit and slide back to lock in place
screw in corners
replace switch knob
plug in dryer
test switch
pull off switch knob
remove two screws at corners of control unit
pull unit toward you to remove
flip over and remove panel
unscrew switch then twist switch to remove from face on control unit
holding new switch next to old, remove wires from old switch and insert onto new switch
place new ... Read more switch on control unit face and twist into position
Install screws
replace panel, flip back over
position control unit and slide back to lock in place
screw in corners
replace switch knob
plug in dryer
test switch
Read less
This part is used to start the dryer once you have selected a setting on the timer.
This part is used to start the dryer once you have selected a setting on the timer.
Installation Instructions
Donald from Kanona, NY
Dryer would run without pushing the Start Button
Turn off the circuit breaker ( Or remove the Fuse/s )to the dryer,
Removed 2 screws that hold the control cluster to the dryer top. Then I slid the control cluster forward and up to release it from the dryer. then I removed the start button knob to the start switch by pulling on it straight out. Next I removed the six 1/4" he ... Read more x head screws from back of the removed control cluster. Then using a flat bladed screwdriver I pried up the tab coming off the switch housing. just enought to allow the switch to be turned a quarter of a turn counter clockwise which allows the switch to be removed from the back of the control cluster. Next with a pair of long nose pliers gently pull straight up on the 2 wire terminals attaching wires to the switch. Make a diagram before removing them so that they can be put on the new switch in the same way. Then orient the new switch with its tab located a quarter turn counter clockwise from the hole you pried the old switch tab from. push down on the switch while turning it clockwise 1/4 turn so the tab on the switch drops into it's locking hole. Then using your diagram put the wire terminals back on the switch terminals in the same order and position they came off. Replace the Control panel with the screws you removed. Next position the control panel feet over the holes for them in the top of the dryer and push back a little on the panel to lock it in the correct position. Then take the two longer screws and put one on each side of the panel at the correct angle (not straight up and down) but tilted forward to match the holes and carefully tighten the screws. Next carefully replace the push to start knob on the new switch. Turn the Circuit Breaker (or reinstall the Fuse/s) for the Dryer back on. Then test and make sure that when you select the cycle and the door is closed that pushing the start switch causes the dryer to start. You have done it!
Removed 2 screws that hold the control cluster to the dryer top. Then I slid the control cluster forward and up to release it from the dryer. then I removed the start button knob to the start switch by pulling on it straight out. Next I removed the six 1/4" he ... Read more x head screws from back of the removed control cluster. Then using a flat bladed screwdriver I pried up the tab coming off the switch housing. just enought to allow the switch to be turned a quarter of a turn counter clockwise which allows the switch to be removed from the back of the control cluster. Next with a pair of long nose pliers gently pull straight up on the 2 wire terminals attaching wires to the switch. Make a diagram before removing them so that they can be put on the new switch in the same way. Then orient the new switch with its tab located a quarter turn counter clockwise from the hole you pried the old switch tab from. push down on the switch while turning it clockwise 1/4 turn so the tab on the switch drops into it's locking hole. Then using your diagram put the wire terminals back on the switch terminals in the same order and position they came off. Replace the Control panel with the screws you removed. Next position the control panel feet over the holes for them in the top of the dryer and push back a little on the panel to lock it in the correct position. Then take the two longer screws and put one on each side of the panel at the correct angle (not straight up and down) but tilted forward to match the holes and carefully tighten the screws. Next carefully replace the push to start knob on the new switch. Turn the Circuit Breaker (or reinstall the Fuse/s) for the Dryer back on. Then test and make sure that when you select the cycle and the door is closed that pushing the start switch causes the dryer to start. You have done it!
Read less