My Orders
Refrigerator Panels
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
Shop By Brand
View More
Popular Refrigerator Panels
This is the evaporator cover assembly for a wide range of Samsung refrigerators. This cover features the evaporator fan assembly and insulation behind it and is installed in the rear of the refrigerator cabinet. If your refrigerator is not cooling properly, or if the evaporator fan is broken and needs replacing, you need to replace it immediately to ensure optimal cooling performance in your fridge. This assembly is made of 25-inch-long white plastic and requires a drill or screwdriver to replace it. This assembly is sold individually and does not come with any other necessary parts or accessories, such as securing screws or brackets.
This is the evaporator cover assembly for a wide range of Samsung refrigerators. This cover features the evaporator fan assembly and insulation behind it and is installed in the rear of the refrigerator cabinet. If your refrigerator is not cooling properly, or if the evaporator fan is broken and needs replacing, you need to replace it immediately to ensure optimal cooling performance in your fridge. This assembly is made of 25-inch-long white plastic and requires a drill or screwdriver to replace it. This assembly is sold individually and does not come with any other necessary parts or accessories, such as securing screws or brackets.
This display cover is for refrigerators.
Display cover supports the display control board and houses the touchpad for the display.
Safely store any food that could deteriorate while the power is off. Unplug the refrigerator before installing this part. Wear work gloves to protect your hands.
This display cover is for refrigerators.
Display cover supports the display control board and houses the touchpad for the display.
Safely store any food that could deteriorate while the power is off. Unplug the refrigerator before installing this part. Wear work gloves to protect your hands.
Installation Instructions
Albert from NORTHVILLE, MI
water / ice selector button broke
two screws on bottom of housing (locater where you set your cup for water / ice ), remove screw-save and reuse-, LIFT UP on housing, there are two "T" type hooks holding housing onto door, pull housing forward, once unhooked then unplug two small wiring harnesses plugs, small tip screw driver helped remove harnesses. Circuit board inside
... Read more
housing has two screws, remove screws and lift circuit borad out, install circuit board into new housing and reinstall two screws, plug harnesses back in, reinstall housing onto door, replace two screws on bottom of housing. Be carefull when handleing circuit board, keep it clean, it may take a little fiddling to place circuit board in new housing.
Read less
Used to cover up the compressor components.
Used to cover up the compressor components.
Installation Instructions
Mario from Rockledge, FL
Water on the floor, fridge leak
Back cover was wet in the area of the inlet valve(sign). Water on the floor. 90% of the time is a leaking inlet valve. But it could be frozen water on the drain pan- so I exposed the radiator fins and drain pan and looked. No ice so I went to the valve and opened the copper line valve and waited a few minutes- as soon as water was ca
... Read more
lled by the. Ice maker it leaked. So I went ahead and replaced the valve and after I made sure no leaks were visible I replaced the back cover and continued to observe and all was good. I treated the fridge as a new installation, changed filter and dumped the next two ice buckets. Then I proceeded to demand brownie points.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This refrigerator ice and water dispenser module assembly serves as the main housing for the dispenser system located on the refrigerator door. Designed in a gray and multicolor finish, it helps support and guide the internal dispenser components for smooth and reliable ice and water dispensing. Made from durable ABS plastic, this assembly is commonly replaced when the dispenser housing becomes cracked, damaged, or when the dispenser lever no longer functions properly, causing issues such as leaking ice or water.
This refrigerator ice and water dispenser module assembly serves as the main housing for the dispenser system located on the refrigerator door. Designed in a gray and multicolor finish, it helps support and guide the internal dispenser components for smooth and reliable ice and water dispensing. Made from durable ABS plastic, this assembly is commonly replaced when the dispenser housing becomes cracked, damaged, or when the dispenser lever no longer functions properly, causing issues such as leaking ice or water.
