Range Seals and Gaskets
Find your part
Enter your model number or a part number and click "Search"Popular Range Seals and Gaskets
Your Price
$8.48
Lint Trap Housing Seal
PartSelect Number PS11741506
Manufacturer Part Number WP339956
This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located in between the lint chute and the bulkhead of your appliance. This foam seal is just over 28 inches long and under 1 inch wide. You may need to replace this part if your clothing is taking too long to dry, or if your dryer is not generating enough heat or no heat at all.
Fixes these symptoms
- No heat or not enough heat
- Noisy
- Takes too long to dry
- See more...
Installation Instructions
Eric from Fort Dodge, IA
dryer drum not turning and no air circulating
replaced motor and drum rear seal as well as idler wheels, the old rear drum seal was completly worn out, since I had it all apart, I replaced lint chute and trap seals and belt and tensioner. I spent less money on parts than if I would have bought a new dryer. The motor was the main problem as the bearings were shot.
Read more...
Your Price
$77.32
Door Gasket
PartSelect Number PS11749287
Manufacturer Part Number WPW10162384
The oven door gasket on your range functions as a seal between the warm interior of your oven, and the outside. It prevents heat from fleeing your oven when the door is closed. Before making any repairs to your oven you should make sure to wear work gloves to protect your hands, and give your oven time to cool. The only tool you will need to make this repair is a pair of needle nose pliers. This oven door gasket comes with built in retaining clips; if any retaining clips from your old gasket are left in the oven make sure to remove them before installing your new gasket.
Fixes these symptoms
- Door won’t close
- Little to no heat when baking
- Oven is too hot
- See more...
Installation Instructions
Lori from Scottsdale, AZ
Needed to replace oven door gasket.
First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum.
Read more...
Your Price
$56.77
Range Oven Door Gasket
PartSelect Number PS8753695
Manufacturer Part Number WB04T10086
The oven door gasket creates a seal between the oven door and the opening of the oven to prevent heat from escaping when the oven is closed.
Installation Instructions
JUDITH from DANVILLE, NH
Oven door gasket needed replacement
Replacement was extremely easy. The new part fit perfectly and installed very easily without tools. Also, I received the part within a few days
Read more...
Your Price
$7.03
Light Gasket
PartSelect Number PS11740863
Manufacturer Part Number WP3184533
This part creates a seal around the light lens and bulb.
Installation Instructions
David from Westminster, CO
Fiber Gasket around Pyrex Light Lens was mis-shaped
All I had to do was unscrew the pyrex lens over the oven light and then remove the old gasket and replace it with the new one. Worked like a champ!
Read more...
Your Price
$53.21
Door Gasket
PartSelect Number PS1019820
Manufacturer Part Number WB04T10050
This oven door gasket prevents heat from escaping the oven cavity when in use.
Installation Instructions
mary from MODESTO, CA
Your Price
$96.54
Oven Door Seal with Clips
PartSelect Number PS440011
Manufacturer Part Number 316239700
Also known as gasket.
Installation Instructions
CHERYL from PERRYVILLE, AR
Gasket missing
I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.
Read more...
Your Price
$77.07
Oven Door Gasket
Viola. Lokks like new. Read more...
PartSelect Number PS11759723
Manufacturer Part Number W10877014
This part is the replacement door gasket for your oven. It is made of gray rubber and is sold individually. The door gasket runs along the circumference of the oven door and creates a seal that insulates the oven and keeps heat in. If your oven will not heat up properly, or if you notice that the door gasket has become loose or worn, it may need to be replaced. To replace the door gasket, you will need to remove the retaining bracket at the bottom of the oven door, then carefully pull the gasket away from the front of the oven cavity. Then, push the new gasket inside the groove on the outside of the oven cavity, securing it with the arrowhead fasteners that are built in to the oven cavity. This is an OEM part from the manufacturer.
Fixes these symptoms
- Door won’t close
- Oven not heating evenly
- See more...
Installation Instructions
Ralph from Green Bay, WI
Original oven gasket had discolored and deteriated, mainly due to use of oven cleaner.
I removed the bottom gasket retainer , single screw, with a screwdriver. The old gasket just pulls away. I cleaned the area under the old gasket with soap and water. I installed the new gasket whcih easily slips in place with the already installed retainer wires into the pre drilled holes. Viola. Lokks like new. Read more...
Your Price
$41.37
Door Gasket
PartSelect Number PS250264
Manufacturer Part Number WB4K1
Installation Instructions
Robert from New York, NY
Door gasket broken up
It took considerable time to remove the door and take it completely apart so the gasket could be inserted, and time again to reassemble properly. The gasket (though the no. was confirmed before ordering) was 3" too short so I had to cut some off the old gasket to make do (not entirely effectively).
Read more...
Your Price
$7.76
Brass Seal
The burner unit slides out easily and after unscrewing the sides, you have to disconnect the wires from the underside of the igniters. The venturi tubes and igniters then unscrew from the underside of the burners which twist right out of the assembly. Re-Assembly is very intuitive looking at it and it all goes right back together as it came out. Took 45 minutes total and that includes fighting with some screws that had rusted onto the burner.
Reading some of the previous reviews, current prices are double to triple what other people did the repair for leading me to believe parts won't be available for much longer. Make the repair while you still can! Read more...
PartSelect Number PS11744111
Manufacturer Part Number WP74005893
This is the replacement brass seal for your range or cooktop. It is made of brass and is approximately 1 inch in diameter. This part may also be known as the surface burner orifice holder seal. It prevents gas leaks between the surface burner orifice holder and the surface burner head. The main reason to replace this part is if the old seal is damaged or missing, as gas can leak out. It is important that you unplug the range and shut off the gas supply before beginning this repair. This part is sold individually and is an authentic OEM part.
Installation Instructions
John from WAKEFIELD, MA
Flames appeared outside of burners
The front burner had a noticible flame coming from the base, so I originally purchased a single burner to replace it (you could see a corroded hole at the bottom). Upon taking the unit apart, I noticed the corrosion was much worse than met the eye. Given the age of the unit and that some parts were already becoming discontinued I decided to gut the whole thing and replace it all.The burner unit slides out easily and after unscrewing the sides, you have to disconnect the wires from the underside of the igniters. The venturi tubes and igniters then unscrew from the underside of the burners which twist right out of the assembly. Re-Assembly is very intuitive looking at it and it all goes right back together as it came out. Took 45 minutes total and that includes fighting with some screws that had rusted onto the burner.
Reading some of the previous reviews, current prices are double to triple what other people did the repair for leading me to believe parts won't be available for much longer. Make the repair while you still can! Read more...
Your Price
$95.68
Oven Door Seal
Once the old seal is out, insert the new one using the wire embedded in the seal as your guide...the gap in the seal goes to the bottom. Put everything back together and re-install the door. My door hinges were spring loaded and took a little effort to move them down so the door can be slipped on. This is a two person job since the hinges do not lock in place, they spring right back up flush with the oven and you cannot install the door. Re-install the two set screws holding the door to the hinges and you are done!
With the new seal in place, it felt a little puffy and the door did not seem to close as flush as it used to. This makes sense since the seal is new. I kept the door locked (like you would to use the oven cleaning cycle). I even kept it partially locked during cooking.
Frankly, the hardest part was the cleanup of nasty grease and dirt that built up over the past decade or so.
Best of luck! Read more...
PartSelect Number PS11757564
Manufacturer Part Number WPY702338
This oven door seal prevents heat from escaping the oven cavity when in use.
Fixes these symptoms
- Little to no heat when baking
- Oven not heating evenly
- See more...
Installation Instructions
Paul from Mickleton, NJ
The oven door seal was ripped and was leaking.
The oven seal replacement was very straight forward. Two screws held the door to the arms coming from the oven. I slid the door up off the arm and moved it to a workbench. This whole process should take about 15 minutes, a little longer if your unit is older and you want to clean as you go. Mine was fairly dirty and I gave it a cleaning as I removed parts. Unscrew all screws on the outer frame of the door, including two small ones on the side. Remove the outer frame and then the glass front and set them aside. A few more screws to remove the glass from the inner door, and even more on the remaining part of the door. You should also remove the screws holding the tiny brackets as well to release the portion that holds the oven seal in place. This is very straightforward, just keep pulling screws out until you can remove the old seal.Once the old seal is out, insert the new one using the wire embedded in the seal as your guide...the gap in the seal goes to the bottom. Put everything back together and re-install the door. My door hinges were spring loaded and took a little effort to move them down so the door can be slipped on. This is a two person job since the hinges do not lock in place, they spring right back up flush with the oven and you cannot install the door. Re-install the two set screws holding the door to the hinges and you are done!
With the new seal in place, it felt a little puffy and the door did not seem to close as flush as it used to. This makes sense since the seal is new. I kept the door locked (like you would to use the oven cleaning cycle). I even kept it partially locked during cooking.
Frankly, the hardest part was the cleanup of nasty grease and dirt that built up over the past decade or so.
Best of luck! Read more...
Brands
- Amana Range Seals and Gaskets
- Bosch Range Seals and Gaskets
- Crosley Range Seals and Gaskets
- Electrolux Range Seals and Gaskets
- Frigidaire Range Seals and Gaskets
- General Electric Range Seals and Gaskets
- Gibson Range Seals and Gaskets
- Hotpoint Range Seals and Gaskets
- Jenn-Air Range Seals and Gaskets
- Kenmore Range Seals and Gaskets
- KitchenAid Range Seals and Gaskets
- Maytag Range Seals and Gaskets
- Roper Range Seals and Gaskets
- Tappan Range Seals and Gaskets
- Thermador Range Seals and Gaskets
- Westinghouse Range Seals and Gaskets
- Whirlpool Range Seals and Gaskets
