My Orders
RCA Refrigerator Hardware
GET YOUR OFFICIAL RCA PARTS TO ENSURE VICTORY
Popular RCA Refrigerator Hardware
This refrigerator door handle mounting screw connects your refrigerator door to the handle. The part is less than 1 inch in length, and can come in both silver and gold colors. When installing this screw, make sure to avoid cross-threading and use reasonable torque to avoid damage to components. This part is an OEM part sourced directly from the manufacturer. This part is sold individually.
This refrigerator door handle mounting screw connects your refrigerator door to the handle. The part is less than 1 inch in length, and can come in both silver and gold colors. When installing this screw, make sure to avoid cross-threading and use reasonable torque to avoid damage to components. This part is an OEM part sourced directly from the manufacturer. This part is sold individually.
Installation Instructions
Jerry from Esparto, CA
Handle broke on the top where the screws go.This is the second handle that broke in the same place in 5 years.
Remove the top screws, with a Philips screw driver, take broken piece out. Then remove the plastic cover on bottom of handle, take the torx screw out. Now handle is off.Put new handle in place and put all three screws back in. Then install new plastic cap, and you are all done.
This is a replacement pack of sheet metal screws for your refrigerator. These are Phillips-head screws, and are approximately ¾ of an inch long. This package contains 12 screws. These screws are typically used to attach your refrigerator or freezer door handles to the door. These screws are OEM parts sourced directly from the manufacturer.
This is a replacement pack of sheet metal screws for your refrigerator. These are Phillips-head screws, and are approximately ¾ of an inch long. This package contains 12 screws. These screws are typically used to attach your refrigerator or freezer door handles to the door. These screws are OEM parts sourced directly from the manufacturer.
Installation Instructions
Carla from BERKELEY, CA
Handles on fridge were discoloured and looked very bad
Actually - we followed the instructions in a video provided by :parts select" when we ordered the parts [the 2 fridge door handles]. It was easy to order with the model number, easy to remove the old handles & easy to install the new ones with the instructions on your web site, and everything arrived timely & reasonably priced. Thanks a
... Read more
heap!
Read less
Installation Instructions
Vicki from APOLLO BEACH, FL
Anger motor died about a year ago, ice maker just quit so replaced both
The auger motor died because two of the screws attaching it had come loose so the motor wasn't properly aligned. Wasn't sure from diagram which was the right screw so ordered two different ones from the parts diagram.
PartSelect videos helped, watched several times until I felt comfortable. Pulled old icemaker first then removed as ... Read more sembly with anger motor, replaced motor per video and put assembly back in. Put new icemaker in and was done is a little over 30 minutes.
PartSelect videos helped, watched several times until I felt comfortable. Pulled old icemaker first then removed as ... Read more sembly with anger motor, replaced motor per video and put assembly back in. Put new icemaker in and was done is a little over 30 minutes.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This water tubing clip, also known as a P-clamp, is usually used within refrigerators and freezers to organize the water line and tubing, but due to its versatility, this clip may also be used in other applications, like securing other cables. Made of metal and measuring approximately 1-inch in length, this clip features a hole on each side to allow you to screw it into the side of your appliance and secure the appropriate valve, tube, or cable. This clip is a genuine OEM part that is sold individually.
This water tubing clip, also known as a P-clamp, is usually used within refrigerators and freezers to organize the water line and tubing, but due to its versatility, this clip may also be used in other applications, like securing other cables. Made of metal and measuring approximately 1-inch in length, this clip features a hole on each side to allow you to screw it into the side of your appliance and secure the appropriate valve, tube, or cable. This clip is a genuine OEM part that is sold individually.
Installation Instructions
Louis from Kingwood, TX
Water leaking into Freezer from Ice Maker
Disregard previous.
1. Turn off water supply.
2. Unplug power cord.
3. Remove bottom Panel to access the Solenoid valve.
4. Remove the water lines from the Valve.
5. Remove the Valve from the refrigerator.
6. Remove the electrical connectors from the valve.
(make sure the new valve has the connector adap ... Read more tors included) you will need them during installation.
7.Bend the new valve bracket inward about 45 degrees to clear the compressor coolant line.
8.Use a pair of pliers to braek away the plastic on the new valve for clearance.
9.If needed remove the compression fitings from the old water line installation as the new valve comes with the push and lock feature.
10.Install the bottom 2 water lines they are different sizes
11.Mount the new valve to refrigerator and tighten.
12.Install the ice maker water line to the top fitting on the valve.
13.Plug the power cord in & turn on the water supply,check for leaks and proper operation on the valve.
1. Turn off water supply.
2. Unplug power cord.
3. Remove bottom Panel to access the Solenoid valve.
4. Remove the water lines from the Valve.
5. Remove the Valve from the refrigerator.
6. Remove the electrical connectors from the valve.
(make sure the new valve has the connector adap ... Read more tors included) you will need them during installation.
7.Bend the new valve bracket inward about 45 degrees to clear the compressor coolant line.
8.Use a pair of pliers to braek away the plastic on the new valve for clearance.
9.If needed remove the compression fitings from the old water line installation as the new valve comes with the push and lock feature.
10.Install the bottom 2 water lines they are different sizes
11.Mount the new valve to refrigerator and tighten.
12.Install the ice maker water line to the top fitting on the valve.
13.Plug the power cord in & turn on the water supply,check for leaks and proper operation on the valve.
Read less
Installation Instructions
Kelly from Canandaigua, NY
Ice Maker would not crush ice.
Removed tray from ref. Removed from cover from tray useing a screwdriver. Removed housing, took old parts out. Make sure you take the parts out in order and put new parts back in same order as old parts.
Size: 10-16 ab. * Part may differ in appearance, but functions same as original. Sold Individually.
Size: 10-16 ab. * Part may differ in appearance, but functions same as original. Sold Individually.
Installation Instructions
Edward from E LONGMEADOW, MA
water leaking from under dishwasher
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.
Indeed ... Read more , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Indeed ... Read more , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Read less