TES355VB0 Estate Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Removed handle on oven door to remove front glass to clean when it slipped out of my hands.
1 person
found this instruction helpful.
-
David from PRESCOTT VLY, AZ
- Really Easy
- Less than 15 mins
-
Screw drivers
To replace, the front glass slides into two holders on the bottom and three groves in the handle, then two screws to attach handle in place on the door.
Was this helpful?
Thank you for voting!
Broken drawer glide
1 person
found this instruction helpful.
-
karen from Thornton, CO
- Really Easy
- Less than 15 mins
-
Screw drivers
Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.
Was this helpful?
Thank you for voting!
Oven Demon Possession
1 person
found this instruction helpful.
-
Kevin from Greensboro, NC
- Really Easy
- Less than 15 mins
Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use
... Read more
the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.
Read less
Was this helpful?
Thank you for voting!
Oven Elementwas burnt into
1 person
found this instruction helpful.
-
Fred from APACHE JCT, AZ
- Very Easy
- Less than 15 mins
-
Screw drivers
Watched the video and did as shown
Was this helpful?
Thank you for voting!
Worn/Bulb Socket
2 of 4 people
found this instruction helpful.
-
JOSEPH from COON RAPIDS, MN
- Really Easy
- Less than 15 mins
-
Screw drivers
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Was this helpful?
Thank you for voting!
slides on lower drawer were broken
2 of 4 people
found this instruction helpful.
-
Leona R from Louisville, KY
- Really Easy
- Less than 15 mins
-
Screw drivers
I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.
Was this helpful?
Thank you for voting!
baking element non operational
1 person
found this instruction helpful.
-
GARY from JACKSON, WY
- Really Easy
- Less than 15 mins
-
Screw drivers
removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!
Was this helpful?
Thank you for voting!
screw came off
1 person
found this instruction helpful.
-
Sandeep from EDINA, MN
- Very Easy
- Less than 15 mins
-
Screw drivers
very expensive to buy the part but just tighten the screw intot eh predefined place.
Was this helpful?
Thank you for voting!
bake element out
1 person
found this instruction helpful.
-
Joyce from BALLWIN, MO
- Really Easy
- 30 - 60 mins
use needle nose pliers to disconnect the element from the power supply. After disconnecting it was easy to repair.
Was this helpful?
Thank you for voting!
range would not heat right
1 person
found this instruction helpful.
-
bobby from HERSCHER, IL
- Really Easy
- 30 - 60 mins
-
Screw drivers
very easy watched the howto you gave
Was this helpful?
Thank you for voting!
Over heating element.
1 person
found this instruction helpful.
-
carlos from TRACY, CA
- Easy
- 30 - 60 mins
-
Screw drivers
Just turn off power , remover screws. Remove and plug in new part.
Was this helpful?
Thank you for voting!
electrical short from oven light.
2 of 4 people
found this instruction helpful.
-
William H. from morehead city, NC
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door.
... Read more
Thank you partselect and i would use them again in the future. billy
Read less
Was this helpful?
Thank you for voting!
Replacing oven light and socket
1 person
found this instruction helpful.
-
Carol from BELLINGHAM, WA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?),
... Read more
which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.
Read less
Was this helpful?
Thank you for voting!
cleaner
2 of 5 people
found this instruction helpful.
-
Mary from Duarte, CA
- Really Easy
- Less than 15 mins
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
Was this helpful?
Thank you for voting!
Light would not light
1 of 2 people
found this instruction helpful.
-
Frank from LEBANON, VA
- Easy
- 15 - 30 mins
-
Pliers
Pop old one out and new one in
Was this helpful?
Thank you for voting!