TES355VB0 Estate Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Heating element, broken
2 of 2 people
found this instruction helpful.
-
Frank from COLUMBIA, TN
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Unplugged appliance, removed the 2 screws that mount element. Unhooked the electric wires,with pliers.
Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.
Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.
Was this helpful?
Thank you for voting!
outer glass on door broke
3 of 5 people
found this instruction helpful.
-
Marc from FOXBORO, MA
- Very Easy
- 15 - 30 mins
-
Screw drivers
used a screwdriver. took very little time and effort
Was this helpful?
Thank you for voting!
Bottom element stopped working
2 of 2 people
found this instruction helpful.
-
ArLinda from ALTON, IL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Unplug the stove from outlet so no power going to appliance. Had to use wd on screws to help loosen
Little bit of effort to loosen. Took new element from package. Replaced screws just tight donot over tighten. Plug stove into outlet turned on. Did a automatic clean. Oven clean and baked cake later I am back in business and 63 years. ... Read more Was quote 240.00 to from a local repair person. When using wd make sure you wipe any drip from before turning on oven.
Little bit of effort to loosen. Took new element from package. Replaced screws just tight donot over tighten. Plug stove into outlet turned on. Did a automatic clean. Oven clean and baked cake later I am back in business and 63 years. ... Read more Was quote 240.00 to from a local repair person. When using wd make sure you wipe any drip from before turning on oven.
Read less
Was this helpful?
Thank you for voting!
Broken Door Handle
2 of 2 people
found this instruction helpful.
-
Daniel from BROOKLYN, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the side covers. Remove the 2 screws on the back side of the door, hold on to the glass and front panel, they will fall out. remove the 2 screws holding the handle. Put the new handle in place and insert screws, note the old handle had metal inserts that are threaded, the new does not. Had to push very hard and let the screws bite
... Read more
into the plastic.
Read less
Was this helpful?
Thank you for voting!
Broiler element burned out
3 of 5 people
found this instruction helpful.
-
chris from HILTON HEAD, SC
- Really Easy
- 15 - 30 mins
-
Screw drivers
After doing a YouTube search. I successfully completed the repair by easily diagnosing the issue with the element.
I watched a video about 5 most common problems with whirlpool broiler elements.
The first being to inspect the element for damage. I found a small section that appeared to be rough and had a raised bump.
I ... Read more decided to order a new element because the oven is older and it wouldn’t hurt to install a new one even if this wasn’t the issue.
Once the part arrived, which it did quickly, I followed the video instructions. It was easy and straight forward. I completed the task in under thirty minutes. It was very simple and I now have a functional broiler element.
I watched a video about 5 most common problems with whirlpool broiler elements.
The first being to inspect the element for damage. I found a small section that appeared to be rough and had a raised bump.
I ... Read more decided to order a new element because the oven is older and it wouldn’t hurt to install a new one even if this wasn’t the issue.
Once the part arrived, which it did quickly, I followed the video instructions. It was easy and straight forward. I completed the task in under thirty minutes. It was very simple and I now have a functional broiler element.
Read less
Was this helpful?
Thank you for voting!
Oven bake would not heat up at all.
2 of 2 people
found this instruction helpful.
-
Wilton from CANYON LAKE, TX
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Very simple.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!
NOTE: The existing element showed no exterior signs of ... Read more being bad.
The damage must have been internal.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!
NOTE: The existing element showed no exterior signs of ... Read more being bad.
The damage must have been internal.
Read less
Was this helpful?
Thank you for voting!
Baking element had burned into
2 of 2 people
found this instruction helpful.
-
Rebecca from LANCASTER, SC
- Very Easy
- Less than 15 mins
-
Screw drivers
The video was very helpful.
Was this helpful?
Thank you for voting!
Old lower element fell apart
2 of 2 people
found this instruction helpful.
-
Matthew from MIDDLETOWN, CT
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
1. Unplug the power
2. Unscrew the two screws that hold the element
3. Pull the element out a little to expose the wires.
4. Gently pull off each wire (best done with needle nose) MAKE SURE THE WIRES DONT FALL INTO THE BACK OF THE OVEN.
5. Firmly seat wires back onto new element and replace screws
6. Bake stuff!
2. Unscrew the two screws that hold the element
3. Pull the element out a little to expose the wires.
4. Gently pull off each wire (best done with needle nose) MAKE SURE THE WIRES DONT FALL INTO THE BACK OF THE OVEN.
5. Firmly seat wires back onto new element and replace screws
6. Bake stuff!
Was this helpful?
Thank you for voting!
Oven not reaching temperature
2 of 2 people
found this instruction helpful.
-
Marsha from Clermont, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Extremely easy repair
2 of 2 people
found this instruction helpful.
-
Melissa from MILL CITY, OR
- Very Easy
- Less than 15 mins
-
Screw drivers
Unplug stove. Remove the two screws attaching the element to the rear of the oven. Carefully pull out. Disconnect wires. Reconnect wires. Screw back in. Done. The hardest part was moving the stove away from the wall.
Was this helpful?
Thank you for voting!
oven handle broke
2 of 2 people
found this instruction helpful.
-
Jim from CAMDENTON, MO
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle
Was this helpful?
Thank you for voting!
the fastener became loose and dropped into the stove
2 of 3 people
found this instruction helpful.
-
George E from OCALA, FL
- Really Easy
- 30 - 60 mins
This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark
George Clark
Was this helpful?
Thank you for voting!
could not control the temp of the element
2 of 3 people
found this instruction helpful.
-
Steve from GREENBRIER, TN
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
take off back panel, simply unplug the old switch and plug in the new one. Simple
Was this helpful?
Thank you for voting!
Burner did not always reduce heat when temp. Was lowered.
2 of 3 people
found this instruction helpful.
-
Annie S from RIDGEVILLE, SC
- Really Easy
- 15 - 30 mins
-
Screw drivers
My husband unscrewed the bad switch and replaced with the new one.
Was this helpful?
Thank you for voting!