TES355VB0 Estate Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burner Would,Nt Heat Up.
-
david from cleveland, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed top of stove replaced heating element ,piece of cake.
Was this helpful?
Thank you for voting!
The Terminel Bloc Overheated And The Bloc Melted Causing The Stove To Cease Fukshioning
-
Joseph from Channelview, TX
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
R&r
Was this helpful?
Thank you for voting!
lower element burned out
-
Ann from Weston, WI
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
So easy. Unplug the range. (really important. You're working with wiring after all) Unscrew the metal plate holding the bake element in place, gently pull out the wires and detach the element from them. (the element just pulls off, but it was attached pretty tightly so I did have to use needlenose pliers to get a better grip on it.) The
... Read more
n simply plug in the new bake element, push the wires back in, reattach the metal plate and bake a cake! Don't even think about calling a repairman for this one! It took under 10 minutes once I got around to ordering the element. (none of the local stores carried them)
Read less
Was this helpful?
Thank you for voting!
Terminal Block was melted where the cord had came lose.
-
Louise from Humansville, MO
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.
Was this helpful?
Thank you for voting!
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
-
Dave from Titusville, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Was this helpful?
Thank you for voting!
Broiler element EXPLODED!
-
Beth from Draper, UT
- Easy
- 15 - 30 mins
-
Screw drivers
Yes... it exploded. Ordered the part which was delivered promptly. Installed in about 30 minutes with a helper. Just unscrew the 4 interior screws and a bunch of the screws (10 maybe?) on the back panel. Drop the back panel, remove the electrical connections from the broiler element and have your helper pull it out. Shove the new one in c
... Read more
arefully through the insulation, attach the two electrical connections and reattach all the screws. Worked fine but smelled a bit as it burned off the new coating. About a 30 minute project.
Read less
Was this helpful?
Thank you for voting!
Oven Self Clean Would Not Function
-
dennis from tonganoxie, KS
- Really Easy
- 15 - 30 mins
-
Screw drivers
Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine.
... Read more
Of course unplug stove before you start !
Read less
Was this helpful?
Thank you for voting!
the boiler went out
-
Angela from Little Hocking, OH
- Easy
- 15 - 30 mins
-
Screw drivers
Unpluged from electric. I took two bolts out of back of oven attached to boiler. Pulled out and exposed cords the attach to boiler. Slide them off and removed old boiler. Attached cords to new boiler and slide part back in to attach the two bolts back. Plugged oven back in and worked great
Was this helpful?
Thank you for voting!
Gas range would not go into self cleaning mode. When pushing the self clean button, would get three beeps!
-
Lee from Saint James, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job.
... Read more
If your handy at all, it should not be a problem.
Read less
Was this helpful?
Thank you for voting!
terminal block back of range shorted and burned
-
Louis from Grantsville, UT
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare
Was this helpful?
Thank you for voting!
Could not get self cleaning oven to engage
-
Charles from Fairfield Bay, AR
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]
Was this helpful?
Thank you for voting!
Power block terminal failure
-
Leonard from Brazoria, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Ordered part needed. Much, much cheaper than purching a new range.
Was this helpful?
Thank you for voting!
8 Inch electric burner not getting hot
-
John from Dover, NJ
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I determined the problem by swapping the 8 inch burner with a 6 inch burner. the 8 inch got hot when connected to the 6 inch wire harness. This told me that the 8 inch burner was good. The 6 inch failed to get hot so I determined the next logical thing was the power to the 8 inch burner. I used a multi meter to determine that power was
... Read more
getting into the control unit but no voltage was getting out. The controller was bad. I ordered a new controller and after unplugging the stove, replaced the controller in about 10 minutes. (Critical part of repair is to unplug unit from wall -220 volts!)
Read less
Was this helpful?
Thank you for voting!
oven element burnt out
-
JoAnne from Harrison, AR
- Really Easy
- 15 - 30 mins
-
Screw drivers
unscrew two screws..took old element out, put perfect fit new element in,screw two screws back in.
Was this helpful?
Thank you for voting!
Light bulb failure
-
Grant from Alexandria, VA
- Really Easy
- Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!