SHREE General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
PIECE BORKEN ON ICE MAKER DRAWER
2 of 2 people
found this instruction helpful.
-
Ann from SIOUX CITY, IA
- Really Easy
- Less than 15 mins
JUST CLEANED NEW DRAWER AND REPLACE
Was this helpful?
Thank you for voting!
ice cube auger broke
2 of 2 people
found this instruction helpful.
-
Marvin from QUINCY, IL
- Very Easy
- Less than 15 mins
removed old ice cube bucket replaced same
Was this helpful?
Thank you for voting!
Ice could not come out the door
2 of 2 people
found this instruction helpful.
-
Jena from Russiaville, IN
- Very Easy
- Less than 15 mins
Took the original ice bucket out and popped the new ice bucket in. Was not sure if the only problem was the augar. This was the simplest way to go.
Was this helpful?
Thank you for voting!
Plastic auger inside ice bucket was broken and not moving ice
2 of 2 people
found this instruction helpful.
-
Annette from SNOW CAMP, NC
- Very Easy
- Less than 15 mins
I ordered the entire ice bucket assembly and just put it in. Simple as that! Awesome company!!
Was this helpful?
Thank you for voting!
Ice dispenser was no longer dispensing ice
2 of 2 people
found this instruction helpful.
-
Pam from ORTONVILLE, MI
- Very Easy
- Less than 15 mins
Removed old dispenser assembly and slide in the new one. That simple.
Was this helpful?
Thank you for voting!
The auger broke on the ice maker
2 of 2 people
found this instruction helpful.
-
Carolyn from DWIGHT, IL
- Very Easy
- Less than 15 mins
We just took out the old ice maker and put the new one in about 2 mintues!!!!
Was this helpful?
Thank you for voting!
noise from freezer.(WhOOOO-oooooh, WHOOO-oooooh,......) annoying with doors closed, worse with freezer door open.
2 of 2 people
found this instruction helpful.
-
paul from PETALUMA, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Watched some videos on youtube after typing in : refrigerator noise, and my model # (in search bar.) Found a video after determining my problem of a gentleman from partselect replacing the evaporator motor. Pretty simple job from video so I went for it ordered parts from them( I fixed the inlet valve on my dishwasher bfore with partselect
... Read more
before). I would call the job easier than it looks. But you need common sense and simple tools and some experience with nuts and bolts and wires. There is one bolt tucked up high under ice maker you may need a right angle nut driver or 1/4 right angle ratchet.(video pointed out). Thanks for video and quality GE parts. I now have a quiet kitchen and great room, with just a low db constant white noise like new.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The refrigerator and freezer were running hot.
2 of 2 people
found this instruction helpful.
-
Glenn from GLENSIDE, PA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I followed the onsite video and had no problems. Shut off refrigerator, removed storage trays and bind, removed the rear panel under the light, identified the orange and pink electrical wires and cut them. Spliced the new wires of the thermostat with refrigerator wire and capped them, applied electrical tape to insure no moister makes con
... Read more
tact with wires. Replaced rear panel and storage racks and bind. Plugged in the refrigerator and it is operations like new. I was about to purchase a new refrigerator for $ 1,300.00 and the thermostat costed $ 13.00. What a Christmas present!
Read less
Was this helpful?
Thank you for voting!
The fan got very noisy.
2 of 2 people
found this instruction helpful.
-
Carol from ORANGE, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
My husband did the repair in 45 minutes and said it was very easy. The video made everything plain and simple.
Was this helpful?
Thank you for voting!
noisy evaporator fan motor
2 of 2 people
found this instruction helpful.
-
Russell from GLEN, NH
- Easy
- 1- 2 hours
-
Screw drivers, Socket set, Wrench set
Replaced evaporator fan motor, and this solved the whistling noise that had developed. Reviewed and followed the removal and installation instruction video as closely as possible. This was very helpful, with a few additions. For the model PS123NGPBBB GE refrigerator/freezer, there were a few differences from the video. There a was an addi
... Read more
tional cover panel that was positioned vertically at the back of the freezer compartment below the auger motor assembly. It was necessary to remove this cover (4 screws) to gain access to the auger motor cover screws. The unit also has a different light configuration with 2 lights. I found it helpful to remove these light bulbs and the corresponding light fixtures in order to remove the evaporator motor assembly. As mentioned in the video, it was necessary to cut the 4 wires from the wire harness of the new motor, and use butt end connectors to reattach these wires to the corresponding wires in the unit. Total job took between 1 and 2 hours, and the motor change solved the noise problem.
Read less
Was this helpful?
Thank you for voting!
Replace water filter with bypass plug - filter is redundant with home osmosis system
2 of 3 people
found this instruction helpful.
-
Fred from LA QUINTA, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
If you have a reverse osmosis system for filtered water system in your home that also feeds the refrigerator, using another water filter in the refrigerator is redundant, so GE makes a Water filter Bypass Cap that allows you to run using the already filtered water without needing to expensive water filter. FIRST - using a phillips screw
... Read more
driver remove the toe kick plate at the bottom front of the refrigerator - two screws - one on each side of the plate that extends the entire width of the refrigerator. SECOND - Locate the water line (should be right in front) and the valve to turn off the water. Turn valve clockwise (right) until completely closed. Then test by attempting to fill a glass with water using the dispenser on the door. If any water continues to come out, continue turning the valve (without forcing it) clockwise until it has been turned as much as possible. If water still comes from dispenser, locate the source of the water line - most likely from under the kitchen sink. There should be another valve under the sink, or simply turn off (turn the cold water valve clockwise) until water cold water completely turned off. Test again as required. THIRD - clear the top right hand back shelf directly under the water filter screwed into the ceiling of the refrigerator in the rear top right side of the refrigerator. Place a small towel under the water filter, and slowly turn the filter 1/4 turn clockwise without using force. Continue turning until the full 1/4 turn is complete and the filter will drop down without pulling. Place the old filter upside down in the sink, thereby allowing the filter to drain any water present in the filter. FOURTH - remove the filter plug from package, notice notches in top of plug that align with gaps in the area where a filter would typically be screwed into the filter location in the ceiling above the top right shelf in the refrigerator. After aligning notches in the bypass plug with gaps in the screw mechanism, carefully turn the bypass plug 1/4 turn counter- clockwise - at which time the bypass plug should be firmly installed. FIFTH - Reverse step SECOND, and turn valve Counter-Clockwise until valve is completely open. Test to ensure no water is leaking from the Bypass Plug. SIXTH - Finally reverse step FIRST by reattaching the toe kick plate using the two phillips screws removed in Step FIRST. NOTE: The Bypass Plug is quite inexpensive, but after adding shipping from Canada - the cost is about the same as purchasing a new filter for the refrigerator. :-(
Read less
Was this helpful?
Thank you for voting!
Icemaker parts were cracked after use
2 of 3 people
found this instruction helpful.
-
Steven from Lacey, WA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I had to replace the whole tray. Required complete disassembly and reassembly. Simple to do. No problems whatsoever!!
Was this helpful?
Thank you for voting!
Huge crack in the vegetable pan cover
2 of 3 people
found this instruction helpful.
-
Stephanie from Conshohocken, PA
- Really Easy
- Less than 15 mins
First, I love that fact that my new fridge piece came in the mail in 2 days! I didn't order it as a rush, but I'm so glad it came so quickly! The installation could not have been easier! It took me longer to clear off my broken vegetable pan cover than it did to pop the new one in. My overall experience was amazing and super easy! I'll be
... Read more
back to PartSelect should I need I need to replace anything else in the future.
Read less
Was this helpful?
Thank you for voting!
Clicking sound. Ice maker would not work and trip the braker if you tries to use it.
2 of 3 people
found this instruction helpful.
-
Marty from Aztec, NM
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
1. Pulled refrigerator out
2. Unpluged the refrigerator
3. Removed the three screws holding the cover on.
4. Removed Board ASM Main Control.
5. Unpluged Connector's.
6. Pluged Connector's in to new Board ASM Main Control.
7. Put cover back on.
8. Pluged refrigerator back in.
9. Pushed refrigerator ... Read more back into place.
2. Unpluged the refrigerator
3. Removed the three screws holding the cover on.
4. Removed Board ASM Main Control.
5. Unpluged Connector's.
6. Pluged Connector's in to new Board ASM Main Control.
7. Put cover back on.
8. Pluged refrigerator back in.
9. Pushed refrigerator ... Read more back into place.
Read less
Was this helpful?
Thank you for voting!
replace main control board
2 of 3 people
found this instruction helpful.
-
Edsel from Haynesville, LA
- Really Easy
- Less than 15 mins
-
Pliers
Unplug the refrigerator from the wall plug and take the plate off of the circuit board in the back of the refrigerator. Remove the screws holding the board in place. Remove the board by pinching the little white pins holding the board inplace. Disconnect the wires from the circuit board and install the new board in its place. Notice the w
... Read more
ire prongs so that they are connected the same as they were on the previous board. Replace the screws that hold the cover. Plug it in. If it does not turn on, remove the plug from the wall and re insert it. The new board has to reset itself.
Read less
Was this helpful?
Thank you for voting!