SHREE General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The ice maker would not crush ice and frequently jammed up.
4 of 7 people
found this instruction helpful.
-
Thomas from Brentwood, TN
- Really Easy
- Less than 15 mins
I determined the moving parts in the ice-maker drawer were completely worn out. The spiral screw assembly that feeds the ice was no longer centered and rather than start changing select pieces I ordered an entire drawer assembly, Pt. No. PS783772. When it arrived I slid out the old drawer, slid in the new and it ended up costing a lot l
... Read more
ess than a service call and parts would have.
Read less
Was this helpful?
Thank you for voting!
Making an owl sound from the icemaker side
3 of 4 people
found this instruction helpful.
-
james from vista, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Simple; Removed the panel, unplugged the cable connections to the mother board with a rat nosed plier.
Then to remove board you must squeeze closed the 4 plastic retainer clips in each corner, or they can accidentally be pulled off with the board.
Removed the board, re-attached the new board on the clips, then the cable connect ... Read more ors, then the panel.
Plugged in the refrige and it has been silent ever since.
Follow the instructions and anyone can do it.
Then to remove board you must squeeze closed the 4 plastic retainer clips in each corner, or they can accidentally be pulled off with the board.
Removed the board, re-attached the new board on the clips, then the cable connect ... Read more ors, then the panel.
Plugged in the refrige and it has been silent ever since.
Follow the instructions and anyone can do it.
Read less
Was this helpful?
Thank you for voting!
Ghostly Sounds From Fan Motor - Variable Speeds All Night - Motherboard Problem
3 of 4 people
found this instruction helpful.
-
Glenn from PORT JEFFERSON, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver
Simple directions were provided. It took more to clean and vaccuum than the actual repair. Yes I replaced the motherboard in a referigerator. Just keep not of the connectors and were they came off from on the original board. Dont just rip them off because the new board has some different connections. So follow the directions and take
... Read more
your time if your not sure. But really it a cinch. No more whoooo sheeesh and howling noises from the referigerator. Thank goodness.
Read less
Was this helpful?
Thank you for voting!
The fridge was making a clicking sound, and not cooling the food
3 of 4 people
found this instruction helpful.
-
Sharon from West Winfield, NY
- Really Easy
- More than 2 hours
-
Screw drivers
The back panel was unscrewed, we read the directions with the circuit board and followed them. It was very easy to unplug the old faulty unit and plug in the new replacement part. It was done in 4 minutes flat. Very easy to do yourselves!
Was this helpful?
Thank you for voting!
Temp panel flashed "hrs", refrigerator would not work
2 of 2 people
found this instruction helpful.
-
Christopher from Chicago, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Remove back panel to expose the control board. Simply unplug cables from old board and pull the board out, no tools required. Put new board in place and replace the cables. Very easy.
Was this helpful?
Thank you for voting!
no water from dispenser, then constant clicking sound, and frig went warm
2 of 2 people
found this instruction helpful.
-
Sonya from Sugar Land, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After reading this forum and other searches, I assumed replacing the board may solve my problem. Unscrewed the back plate, used pliers to pull out the connectors, squeezed in the sides of the 4 plastic white board holders to release the board, and then replaced old board with the new one and reconnected connectors. (My model was not one o
... Read more
f the mentioned models for cutting the 2nd pin of the J1 connector, so I left it in.) Upon plugging my frig back in, it began working perfectly again. So thankful to have found this forum!
Read less
Was this helpful?
Thank you for voting!
Refrigerator would not get cold
4 of 8 people
found this instruction helpful.
-
Trudy from Saint Cloud, FL
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
UNPLUG! (Read Instructions for wiring configuration) Remove cover lower back right hand side.Remove ribbon plugs top and bottom you will need to lever back holding tab while pulling plug they will more than likely break dont worry you are throwing this part away., disconnect ground wire, compress plastic holding tabs,
pull off contro ... Read more l board, plug in new board push on to holding tabs reconnect ground and turn on refrigerator and check replace cover, everything is now working great.
pull off contro ... Read more l board, plug in new board push on to holding tabs reconnect ground and turn on refrigerator and check replace cover, everything is now working great.
Read less
Was this helpful?
Thank you for voting!
Unit was dead
2 of 2 people
found this instruction helpful.
-
Carl from BELLVILLE, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Removed and replaced control board
Was this helpful?
Thank you for voting!
Not cooling the bottom
2 of 2 people
found this instruction helpful.
-
John M from SAN ANTONIO, TX
- Really Easy
- 15 - 30 mins
-
Socket set
Disconnect the refrigerator, remove & installed new fan evaporator motor
Was this helpful?
Thank you for voting!
Lost Temperature in Refrigerator and Freezer, making clicking noise
2 of 2 people
found this instruction helpful.
-
john from Madison, OH
- Easy
- Less than 15 mins
-
Screw drivers
Removed main control board cover on back of refrigerator (3 screws). Unplugged power to refrigerator and removed electrical connections to control board using a screwdriver. Using a screwdriver disconnected (4) plastic self -locking prongs holding the board. Matched new replacement board with old board. Plugged in electrical connection
... Read more
s to new board. Snapped main control board onto (4) self- locking prongs. Reinstalled cover (3) screws. Plugged in refrigerator and tested refrigerator operation.
Read less
Was this helpful?
Thank you for voting!
Fan was not running to circulate the air; found resistors burned on main board
2 of 2 people
found this instruction helpful.
-
Greg from Damon, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the board cover from the back, removed old board, installed new board, installed cover.
Was this helpful?
Thank you for voting!
Refigerator quit running
2 of 2 people
found this instruction helpful.
-
Allen from Smithland, KY
- Really Easy
- Less than 15 mins
Removed back cover from unit. unpluged wirring harness installed new control board and refigerator runs lik new
Was this helpful?
Thank you for voting!
Main Board failed
2 of 2 people
found this instruction helpful.
-
Joseph from Marrero, LA
- Really Easy
- Less than 15 mins
-
Nutdriver
Part arrived 2 days before anticipated. I was able to keep my fridge running long enough to get the new part in, which took no time at all. The Main Board relay would start clicking and the compressor would shut down. By unplugging the top right plug for a minute and plugging it back in I was able to keep it running for a few hours at a t
... Read more
ime. Good enough to keep my food from going bad. Thr part was an easy plug in replacement, was a good price, and works great.
Read less
Was this helpful?
Thank you for voting!
Broken crisper drawer cover
2 of 2 people
found this instruction helpful.
-
Wanda from HOUSTON, TX
- Very Easy
- Less than 15 mins
After removing all items from the broken top, I removed both drawers and crisper top. I then slid the new top in place and replaced the drawers which easily slid into the grooves in the underside of the top.
Was this helpful?
Thank you for voting!
No Cooling on either freezer or refrigerator
2 of 2 people
found this instruction helpful.
-
jaime from SYLMAR, CA
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set
Everything seemed to be working right, but no cooling, so I tried turning on and off the switch that turns the light on 5 times within two seconds, refrigerator did not shot. so I removed the main board and I notice a short had taken place on one of the relay legs. I ordered the main board and replaced it. The main board is on the back
... Read more
of the freezer covered with a sheet metal panel about 8"x8" and is secured with hex sheet metal screws. Everything is working now. Please make sure to unplug the unit from power before removing the main board.
Read less
Was this helpful?
Thank you for voting!