- Home
- JMP31CL2CC
- Instructions
JMP31CL2CC General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Intermittent heat then no heat on oven element
2 of 3 people
found this instruction helpful.
-
Bruce from AKRON, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.
One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer ... Read more works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.
One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer ... Read more works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.
Read less
Was this helpful?
Thank you for voting!
Bottom heating element shorted out
1 person
found this instruction helpful.
-
Karen from CHARLESTON, WV
- Difficult
- More than 2 hours
I have replaced the stovetop burners, so thought the piece would slide into place, but I couldn't get it to catch. Had to call in a professional. He knew what he was doing and popped it into place in just a few minutes.
Was this helpful?
Thank you for voting!
Two blocks kept shorting out.
1 person
found this instruction helpful.
-
Evelyn from FRANKLIN, NH
- Easy
- 1- 2 hours
-
Socket set
After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son h
... Read more
ad spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.
Read less
Was this helpful?
Thank you for voting!
The broiler element burned out in the oven.
1 person
found this instruction helpful.
-
Ken from Mayfield, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
As with all of my orders from Part Select the part was as correct and arrived in a timely manner. The installation was easy. Remove two screws, unplug the old element from the wires, install wires on new element and reinstall the element. Restored power and everything worked fine.
Thanks,
Ken Fuelleman
Thanks,
Ken Fuelleman
Was this helpful?
Thank you for voting!
Could not adjust heat on burner.
2 of 4 people
found this instruction helpful.
-
Roy from Au Gres, MI
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Followed directions given by previous customers problems which we found on the internet.
Was this helpful?
Thank you for voting!
Element blew hole in self then no power to burner.
2 of 4 people
found this instruction helpful.
-
Melvin from Portland, TN
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this helpful?
Thank you for voting!
Needed New Burner Bowls
2 of 4 people
found this instruction helpful.
-
Carolyn from Garden City, ID
- Really Easy
- Less than 15 mins
Removed the old burner bowls, replacing them with the new ones.
Other Parts Used:
Was this helpful?
Thank you for voting!
Old drip bowls were badly tarnished . . . shine could not be restored.
1 person
found this instruction helpful.
-
Paul from PROVO, UT
- Really Easy
- Less than 15 mins
1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod un
... Read more
it and bowl into the hole in the range top.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
burner was not heating
1 person
found this instruction helpful.
-
lucille from HAPPY CAMP, CA
- Very Easy
- 15 - 30 mins
-
Screw drivers
unplug it and plug the new one in
Was this helpful?
Thank you for voting!
on off switch smoked and smelled hot
1 person
found this instruction helpful.
-
john from MILROY, PA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
standard procedure, very simple
Was this helpful?
Thank you for voting!
control switch had stopped working, burner wouldn't work properly
1 person
found this instruction helpful.
-
Ruth from JACKSON, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
took out a couple of screws and replaced with new switch, plugged in switch wires. very easy
Was this helpful?
Thank you for voting!
a segment of the broil element took on fire
2 of 4 people
found this instruction helpful.
-
maria from great neck, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
it was real easy, I just watched my husband do it!
Was this helpful?
Thank you for voting!
The light socket cup could no longer hold the bracket that holds the light cover in place.
1 person
found this instruction helpful.
-
Roger from ALPENA, MI
- Really Easy
- 30 - 60 mins
-
Socket set
I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with th
... Read more
e part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.
Read less
Was this helpful?
Thank you for voting!
Replaced the outlet the one of the top burners on top of my stove, it went very well.
1 person
found this instruction helpful.
-
Charles from MECHANIC FLS, ME
- Easy
- 30 - 60 mins
-
Screw drivers
I followed the instructions on the video, the only thing they left out is where the wires go through to the back of the stove being that there are sharp edges. A role of glass tape would have been handy to replace the old tape. Thanks for asking, I hope this helps someone else.
Was this helpful?
Thank you for voting!
burner terminal block was worn out
1 person
found this instruction helpful.
-
Mario from RENO, NV
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the b
... Read more
urner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you
Read less
Was this helpful?
Thank you for voting!