- Home
- JMP31CL2CC
- Instructions
JMP31CL2CC General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The burner bowls were burnt through and nasty looking.
3 of 3 people
found this instruction helpful.
-
Isabel from The Colony, TX
- Really Easy
- Less than 15 mins
I carefully removed the burners, removed the bowls and replaced them with the new ones. Easy as pie!
Other Parts Used:
Was this helpful?
Thank you for voting!
Switch started arcing in the dial range of 2 to 8 in about a year.
3 of 3 people
found this instruction helpful.
-
Brian from HONEA PATH, SC
- Very Easy
- Less than 15 mins
-
Screw drivers
Pulled the range out and unplugged it. Removed the back panel. Removed one wire at a time and plugging it in on the new switch. unscrewed the existing switch from the front panel (Two screws). Screwed the new one in, replaced the panel, plugged in the range and tested it. The new switch was a perfect OEM replacement and worked perfectly.
Was this helpful?
Thank you for voting!
Switch was not turning off range indicator light
3 of 3 people
found this instruction helpful.
-
Charles from PORTLAND, OR
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connecti
... Read more
ons. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!
Also follow the installation videos from PartSelect - very helpful!
Read less
Was this helpful?
Thank you for voting!
Two sockets for electric elements and their end terminals were badly burned.
4 of 6 people
found this instruction helpful.
-
Marco from Santa Barbara, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For eac ... Read more h unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!
That's it! It took about 20-30 minutes.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For eac ... Read more h unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!
That's it! It took about 20-30 minutes.
Read less
Was this helpful?
Thank you for voting!
The burner coil had shorted out and actually burnt a hole in my non stick pan and after I replaced that, it would not heat up again. I actually swapped the wires from the back burner, but the small coils use a different watt switch and it would barely boil water with the big coil. So I ordered this
4 of 6 people
found this instruction helpful.
-
sherman from OPELOUSAS, LA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First turn off the breaker, and test with my milti meter. Raise the top panel where the coils are and prop it open high enough to use a screwdriver to open the front panel.
Then unscrew the three screws on the inside of the top panel, then open the oven door and you will see 4 screws across the bottom of thefront control board panel ... Read more and two more on each side of the sides of the panel facing straight up. Unscrew those 6 screws and then pull the front control panel forward and out. You might need something or someone to hold the panel, I just let the wires hold the weight, but not highly recommend. Then pull the switch knob off and behind it there are two little bitty screws that hold the switch in place. Unscrew them and pull the switch out of its place. I put the new switch close to the old one and just used the needle nose pliers to unplug one wire at a time and plug it in on the same place as the old one.
Then screw the itty bitty screws in the front that hold the switch in place and put tbe knob back on. Reposition the front panel back into place abs screw in the 9 screws removed for disassembly. Now would be a good time to clean under the burner panel if you haven’t done so yet ( it gets pretty nasty under there). Then put your burner top back down into place and turn your breaker back on. You can either test with your multi meter or like I did, just put the burner on high and watct the coils glow. Such a beautiful sight. Easy fix.
Then unscrew the three screws on the inside of the top panel, then open the oven door and you will see 4 screws across the bottom of thefront control board panel ... Read more and two more on each side of the sides of the panel facing straight up. Unscrew those 6 screws and then pull the front control panel forward and out. You might need something or someone to hold the panel, I just let the wires hold the weight, but not highly recommend. Then pull the switch knob off and behind it there are two little bitty screws that hold the switch in place. Unscrew them and pull the switch out of its place. I put the new switch close to the old one and just used the needle nose pliers to unplug one wire at a time and plug it in on the same place as the old one.
Then screw the itty bitty screws in the front that hold the switch in place and put tbe knob back on. Reposition the front panel back into place abs screw in the 9 screws removed for disassembly. Now would be a good time to clean under the burner panel if you haven’t done so yet ( it gets pretty nasty under there). Then put your burner top back down into place and turn your breaker back on. You can either test with your multi meter or like I did, just put the burner on high and watct the coils glow. Such a beautiful sight. Easy fix.
Read less
Was this helpful?
Thank you for voting!
burner not work
3 of 4 people
found this instruction helpful.
-
SILVIA from Midlothian, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la e
... Read more
stufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.
Read less
Was this helpful?
Thank you for voting!
Drip pans on stove top burned black
3 of 4 people
found this instruction helpful.
-
Dan from Tucson, AZ
- Really Easy
- Less than 15 mins
I got tired of trying to find the right parts in the stores and decided to order them. Finally I have the drip pans that fit my range!
Other Parts Used:
Was this helpful?
Thank you for voting!
In My Carelessness, I Ruined The Burners On My Stove Using A Really Abrasive Cleaner, And Had To Replace Them With New Ones. My Stove Looks Brand New, And I Feel Better!!
3 of 4 people
found this instruction helpful.
-
Diane from Fraser, MI
- Really Easy
- Less than 15 mins
Nothing to it. Took off the old ones and put on the new! Tada - new stove!!
Other Parts Used:
Was this helpful?
Thank you for voting!
The temperature indicator light on the oven was broken.
3 of 4 people
found this instruction helpful.
-
Jewel from Nacogdoches, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the control panel by removing 7 screws and replaced the light indicator and lens.
Was this helpful?
Thank you for voting!
Replacement of old parts
3 of 4 people
found this instruction helpful.
-
Margaret from Norwalk, CT
- Really Easy
- Less than 15 mins
Fortunately there was no repair needed, just a replacement of old parts, but I was very pleased with the speed of delivery and the quality of the parts. I'm a happy customer.
Other Parts Used:
Was this helpful?
Thank you for voting!
F2 error code when oven was set at a higher temperature.
3 of 4 people
found this instruction helpful.
-
Rachele from OCEANSIDE, CA
- A Bit Difficult
- 30 - 60 mins
-
Socket set
I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip discon
... Read more
nected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.
Read less
Was this helpful?
Thank you for voting!
drip pans had become old and burned out
3 of 4 people
found this instruction helpful.
-
aiden from philadelphia, PA
- Really Easy
- 30 - 60 mins
Took off the ring burners and the old drip pans . installed the new drip pans and the old burners took less than 3 minutes...so easy
Other Parts Used:
Was this helpful?
Thank you for voting!
Terminal block connectors worn out wasn’t making a good connection with the stove top burner
2 of 2 people
found this instruction helpful.
-
Lance from HAHIRA, GA
- Really Easy
- 30 - 60 mins
-
Nutdriver
Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.
Was this helpful?
Thank you for voting!
Alarm would sound whenever oven turned on - with an error message code
2 of 2 people
found this instruction helpful.
-
Carolyn from MASON, MI
- Really Easy
- 30 - 60 mins
-
Screw drivers
Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the o
... Read more
fficial Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!
Read less
Was this helpful?
Thank you for voting!
Was burned out
2 of 2 people
found this instruction helpful.
-
BRINDIA from DOVER, TN
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Took back off and replaced.
Was this helpful?
Thank you for voting!