- Home
- JMP31CL2CC
- Instructions
JMP31CL2CC General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water dumped over in in my overhead microwave, which dripped down on, & shorted out a burner switch.
1 of 3 people
found this instruction helpful.
-
Deanna from Buckeye, AZ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that
... Read more
burner works good as new.
Read less
Was this helpful?
Thank you for voting!
Element burned out.
1 of 3 people
found this instruction helpful.
-
Harden from Lynchburg, VA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I spent half an hour finding my driver set. It took about 25 minutes to turn the power off, remove the racks and element and replace the new elements.
Was this helpful?
Thank you for voting!
Burned out broil element
0 of 1 people
found this instruction helpful.
-
Beverly from Baton Rouge, LA
- Really Easy
- 15 - 30 mins
-
Socket set
.Received the part promptly. Installed it in about 30 minutes. With appliance servicemen, I figure I saved about $200.00 doing it myself. Thanks
Was this helpful?
Thank you for voting!
burner didn't work, using a test light showed only one side was hot.
0 of 1 people
found this instruction helpful.
-
Kathleen M from Nampa, ID
- Really Easy
- Less than 15 mins
-
Screw drivers
took the back panel off the range, took the 2 screws holding the switch in place, took the old switch out, marked the wires took the wires off and clipped them onto the new switch, put the new switch into the switch plate, replaced the screws put on the knob, put the panel back on the range. rolled the range back into it's place. turned
... Read more
the buner on to check if it worked. It did so we were done.
Read less
Was this helpful?
Thank you for voting!
eye wouldnt come on
0 of 2 people
found this instruction helpful.
-
daniel from valentines, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this helpful?
Thank you for voting!
burner was inoperative
0 of 2 people
found this instruction helpful.
-
bryan from cocoa, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
after extremely fast
service from partselect thank you
Was this helpful?
Thank you for voting!
Burner not heating.
1 of 5 people
found this instruction helpful.
-
Jack from Greensboro, GA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Isolated to control switch.
Replaced
Replaced
Was this helpful?
Thank you for voting!
Broil element burned out, literally!
-
Judith from Franklin, NC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Turned off power to oven. Lifted off the oven door. Removed four 1/4 " bolts from outside of fan housing. Removed two 1/4" bolts holding element. Removed element from three clips holding it to upper oven surface. Unplugged two element wires. Reassembly was the reverse. I am an auto mechanic by trade and this was a fairly simple process.
Was this helpful?
Thank you for voting!
Burner wouldnt heat
-
Mary from Leon, KS
- Easy
- 30 - 60 mins
-
Nutdriver
Watched video,and used it as guideline.Biggest problem was removing tape from old wires.
Was this helpful?
Thank you for voting!
Burn box had rusted through under one burner.
-
John from Belle Plaine, MN
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers
With a nut driver removed the four heating element sockets (four small sheet metal screws) and the seventeen sheet metal screws that secured the burn box, removed the sheet metal box and inserted the new one. Not all the holes lined up at first for the screws, but starting in front with the four that did fit, the sheet metal gradually li
... Read more
ned itself up with all the other holes for a perfect fit.
Read less
Was this helpful?
Thank you for voting!
Burner would not turn off
-
Thomas from Winter Garden, FL
- Easy
- 30 - 60 mins
-
Screw drivers
The burner light did not turn off, and the rear burner stayed hot. Unplugged unit and removed switch, which turned off the "burner lit" lamp. Thus I figured it was the switch that was causing the problem. Ordered the switch (I think around $18 and plugged it in. I think there were 4 screws to get the panel off, and then another 2 to get t
... Read more
he switch off. When I plugged the unit back in (it had been unplugged while I waited for the part to ship) it beeped for a while. I had to turn the breaker on and off, and that solved the beeping problem.
Read less
Was this helpful?
Thank you for voting!
The range kept giving an F2 alarm
-
Les from Coal Creek, CO
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in
... Read more
the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.
Read less
Was this helpful?
Thank you for voting!
2 mounting bracket included, wires too long
-
Fuad from Sarsota, FL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers
I couldn't tell which one work best till I installed 2 units and I liked the other bracket for stability.The wired were too long and there is not a given way to strap them and keep them away from the heat source.
Was this helpful?
Thank you for voting!
Burner Would Not Turn Off
-
BILLY from WEBSTER, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver
Replace control switch
Was this helpful?
Thank you for voting!
Broiler element would not heat
-
George from Fairport, NY
- Really Easy
- 15 - 30 mins
-
Socket set
After turning off power, I removed the two screws and pulled the element and wires out, removed the wires and then attached them to the new element and replaced the screws. However, this did NOT correct the problem. The broiler did not work until I tried several times turning it on and off. It then worked once but then did not. It worke
... Read more
d once more after several tries. I then called a repairman suspecting the control board. He confirmed this and tested the old element which was in good working order after all. A new board has been ordered.
Read less
Was this helpful?
Thank you for voting!