EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCSP39WV2WW General Electric Range - Instructions

All Instructions for the JCSP39WV2WW
91 - 105 of 318

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
bake element was broken
1 person found this instruction helpful.
  • allen from MT. AIRY, MD
  • Easy
  • 15 - 30 mins
  • Nutdriver
i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!
Was this helpful?
Thank you for voting!
oven heating element burned out
1 person found this instruction helpful.
  • Howard from East Orleans, MA
  • Easy
  • 15 - 30 mins
  • Pliers, Socket set
First turned off the power to the stove at the breaker panel, thenI removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Disconnecting/reconnecting the "clips" was the only difficult part because they did not slip off/on easily. Replaced the element in the ov en, replaced the screws...good to go!

Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!
Was this helpful?
Thank you for voting!
Uns rewed and pulled out
1 person found this instruction helpful.
  • Kathy from madison, WI
  • Really Easy
  • 15 - 30 mins
  • Wrench set
At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!
Was this helpful?
Thank you for voting!
Oven no longer heated except for Broil element
1 person found this instruction helpful.
  • Derrick from Ypsilanti, MI
  • Easy
  • 15 - 30 mins
  • Socket set
1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven
Was this helpful?
Thank you for voting!
bake element was fried
1 person found this instruction helpful.
  • William from MARTIN, GA
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Pliers
I went by the video
Was this helpful?
Thank you for voting!
inner element not working
1 person found this instruction helpful.
  • Michael from BAY CITY, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
opened oven door and removed two 1/4 " screws from range top. lifted range top and propped open like a car hood with a 1" diam dowel rod. marked on new element the wire color locations from old element and removed wires. removed the two small screws and clips that hold the element to the range top and removed element. Matched where the mounting screws locate to the new element. Installed new element in reverse order.
Was this helpful?
Thank you for voting!
Oven would not heat
1 person found this instruction helpful.
  • Franz from CRESTVIEW, FL
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Removed old broken element and installed new one. Took less than 10 minutes
Was this helpful?
Thank you for voting!
element broke
1 person found this instruction helpful.
  • Richard from NEW BERLIN, NY
  • Really Easy
  • Less than 15 mins
  • Nutdriver
took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.
Was this helpful?
Thank you for voting!
Small burner of Dual Burner no longer would work.
1 person found this instruction helpful.
  • Jerry L from Palmetto, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Pull out Range and unplug from wall receptacle. Open Range door and remove 2 hex head screws with pliers. Screws located at top inside of range door opening. They hold the burner top in place. Slowly lift front of top burner section up and at same time slightly lifting back of burner section since it rests on 2 pivots. Prop front of burner section open, tilted back, with a piece of 2X4 maybe 2 1/2 ft. long. Make sure the 2X4 is located at the front/middle of range [resting on insulation] and at front middle of burner top to keep it opened firmly and balanced. You have about 5 or 6 wire clips to remove from elec. posts. Use pliers to gently remove clips. Tag the wires with tape to remember which wires go onto the new burner. Or take a close up picture with your phone to remember which wires go where. There are 2 philips head screws holding clips that hold the burner in place. The clips are slipped into a slot to help hold them in place. Mark the 2 slots so that when you remove the clips you will remember which slots to put them back into. You will need to hold the burner with one hand while you are removing the last clip as it could just fall out. Remove old burner and install new burner at same angle as was the old burner. You will have to make sure that the 2 clips are in the slotted openings first as you can not put them in place after the burner is installed in the opening. Reinstall the 2 screws into the 2 clips. Hold the electrical pole fittings with one hand while you gently reattach the electrical clips with a set of pliers. You may need to wiggle the clips back and forth to get them on securely. Remove the 2X4 and gently lower the burner top. The hardest part is now you have to slightly lift the back of the burner top while the front is lifted up and maneuver the back to drop down over the 2 pivots. Then the burner top will drop down in place so that the 2 screws in the range door opening can be reinstalled. I don't know of an easy way of making the top of the burner section fall down over the pivots except trial and error. Maybe use a flashlight to look back where the pivots are located while the top is propped open. That may help you visually to see what you are trying to do.
Was this helpful?
Thank you for voting!
Lower bake element burned out.
1 of 2 people found this instruction helpful.
  • Elaine from Hanover, PA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
1. Turned off power at the breaker box. Removed oven door from oven, and removed bake racks. Determined replacement element from PartSelect was correct. Inspected new element. Using meter, determined new element was OK via continuity test. Gathered all appropriate tools to do the job.
2. Using 1/4" nut driver, removed two reta ining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake
Was this helpful?
Thank you for voting!
heating element shorting out-sparking
1 of 2 people found this instruction helpful.
  • K from PERRYVILLE, MO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I turned off electric to the stove. In the oven, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. After unpacking the new element, I placed it in the bottom of the oven, reconnected the two wires, and gently fed the wires back into the back of the oven. I then secured the new unit to the oven wall with the two screws.
Was this helpful?
Thank you for voting!
Just follow the enclosed instructions
1 of 2 people found this instruction helpful.
  • HAROLD from Tucson, AZ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Followed the instructions
Was this helpful?
Thank you for voting!
Bad sensor
1 of 2 people found this instruction helpful.
  • John from CASPER, WY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
By myself
Was this helpful?
Thank you for voting!
Bake element broken
1 of 2 people found this instruction helpful.
  • Charles from Damascus, MD
  • Easy
  • Less than 15 mins
  • Wrench (Adjustable)
Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven . I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.
Was this helpful?
Thank you for voting!
Baking element burned through.
1 of 2 people found this instruction helpful.
  • James from Seattle, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."

Disconnecting the two wires and recon necting them was a simple operation after I cleaned my pants from the electrical short.

Re attaching the two-screw panes to hold the element in place finished the project.
Was this helpful?
Thank you for voting!
All Instructions for the JCSP39WV2WW
91 - 105 of 318