- Home
- JCSP39WV2WW
- Instructions
JCSP39WV2WW General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Repair was slow, due to replacement part was incorrect. Original part had two spring loaded spacers, & holes for them to sit in. The replacement part did not have holes. I was able to drill two holes to make it work.
1 person
found this instruction helpful.
-
Victor from FAYETTEVILLE, GA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 scr
... Read more
ews & turned on circuit breaker.
Read less
Was this helpful?
Thank you for voting!
Replaced stove top burner element
1 person
found this instruction helpful.
-
Steve from Forest, VA
- Easy
- 1- 2 hours
-
Screw drivers, Socket set
Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical ... Read more to wall outlet. Turn on burner element and verify that it works.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical ... Read more to wall outlet. Turn on burner element and verify that it works.
Read less
Was this helpful?
Thank you for voting!
Heat element burned out
1 person
found this instruction helpful.
-
Donna from Thornville, OH
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..
Was this helpful?
Thank you for voting!
Oven wouldn't heat - wire not exposed
1 person
found this instruction helpful.
-
Donald from Gulf Breeze, FL
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
Removed two screws and removed the oven elelent. One wire was not through the back of the stove. Ordered new element anyway. Slid stove out (slide-in model). Unplugged power. Removed two covers protecting wires on back of stove. Found wire for oven element. Had to cut and strip end of wire and use new blade clip. Crimped new clip
... Read more
to wire and inserted into oven through back of stove. Replaced covers. Plugged oven element to wires and tried out oven. WORKED ! Saved new oven element for next time. Difficulty encounted was lack of knowledge on where stove was screwed into counter-top and what size blade clip to buy. It always helps to have a dog 3" away just itching to lend a paw.
Read less
Was this helpful?
Thank you for voting!
No heat lower bake unit / Broiler unit heats ok
1 person
found this instruction helpful.
-
Richard L. from Clear Spring, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on
... Read more
terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power
Read less
Was this helpful?
Thank you for voting!
oven coil caught on fire and broke in half!
2 of 4 people
found this instruction helpful.
-
Cynthia from Houston, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
I turned off the main power! Then unscrewed the back cover unhooked the wires and unscrewed the coil inside of the oven and pulled it out. My 10yr old son and I measured it and went online to order the part. I first did go into BestBuy and they didn't have the part (But they tried to sale me a new oven!) LOL Now who said a newly divorc
... Read more
ed mom couldn't fix her own oven! My Tech Support skills came in handy! Women Rock! LOL
Read less
Was this helpful?
Thank you for voting!
The center element of the 2-stage electric burner failed.
2 of 4 people
found this instruction helpful.
-
Robert from Cinnaminson, NJ
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The cooktop is just set in the counter with no fasteners. I shut off the power and lifted the unit out. Ten small screws held the top to the body. After removal, I took a picture to have a wiring reference. I disconnected five wires with push-on terminals, then removed two Tinnerman nuts with needle-nose pliers. The failed burner was
... Read more
free to remove. There were two mounting ears on the bottom of the burner at positions 12 and 48 as stamped on the bottom. I transferred the mounting ears to the new burner, one screw each. I then positioned the new burner and secured with the two Tinnerman nuts, replaced the five wires, screwed the top back on and slipped the unit into the counter. Done.
Read less
Was this helpful?
Thank you for voting!
Small element in center burned into(inoperative
1 person
found this instruction helpful.
-
Douglas from Gravette, AR
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
1.Move range in position to access electrical wall disconnect and unplug. 2.Remove two 5/16 screws (located under top fwd. edge of cook top, Lift entire top assy up from front and prop with appropriate device(short 2x4 about18 inches long works well) 3.Remove two small phillips screws securing two metallic keeper devices holding burner a
... Read more
ssy in place. This should allow burner assy to be removed.4.Disconnect electrical spade connectors from ceramic terminal blocks on old burner assy.CAUTION: [SPADE CONNECTORS FIT TIGHTLY DO NOT PULL ON WIRES USE PRYING FORCE WITH FLAT SCREWDRIVER DIRECTLY ON TERMINAL].Remove connectors one at a time re-connecting to same location on new assy. Reassemble in reverse order.
Read less
Was this helpful?
Thank you for voting!
Oven would not get to temperature...200 degrees max
1 person
found this instruction helpful.
-
Jan from Rockport, ME
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!
Install new element by reversing above sequence. Then test and push oven back in place. Easy!
Was this helpful?
Thank you for voting!
Lower oven heating unit burnt out
1 person
found this instruction helpful.
-
MARTIN from NAPERVILLE, IL
- Easy
- 15 - 30 mins
-
Nutdriver
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)
Was this helpful?
Thank you for voting!
Bake element caught fire and melted
2 of 4 people
found this instruction helpful.
-
Fareed from Randolph, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver
Turn off power at the circuit breaker before working on electric thing.
Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.
Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.
Was this helpful?
Thank you for voting!
The old heating erlement basically melted and broke in two places
1 person
found this instruction helpful.
-
Coleen from Danville, IN
- Easy
- 15 - 30 mins
-
Screw drivers
I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!
Was this helpful?
Thank you for voting!
The bake element was burnt out.
1 person
found this instruction helpful.
-
Linda from Fort Collins, CO
- Really Easy
- 15 - 30 mins
-
Nutdriver
It took a nutdriver to remove two nuts. The defective element was removed and the replacement installed. It works great!
Was this helpful?
Thank you for voting!
Element burned out.
1 person
found this instruction helpful.
-
lynette from Bowling Green, KY
- Easy
- 15 - 30 mins
-
Pliers
Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit br
... Read more
eaker back on, turned the oven on.... made brownies (o:
Read less
Was this helpful?
Thank you for voting!
Replace bake heater element
1 person
found this instruction helpful.
-
Douglas from Corvallis, OR
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings
... Read more
. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.
Read less
Was this helpful?
Thank you for voting!