EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP35SK2SS General Electric Range - Instructions

All Instructions for the JCBP35SK2SS
106 - 120 of 474

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
When you touched any button on the controls LOC on appeared.
3 of 3 people found this instruction helpful.
  • Roger from HUNTSVILLE, AL
  • Very Easy
  • Less than 15 mins
Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whi pping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Was this helpful?
Thank you for voting!
The burner coil had shorted out and actually burnt a hole in my non stick pan and after I replaced that, it would not heat up again. I actually swapped the wires from the back burner, but the small coils use a different watt switch and it would barely boil water with the big coil. So I ordered this
4 of 6 people found this instruction helpful.
  • sherman from OPELOUSAS, LA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First turn off the breaker, and test with my milti meter. Raise the top panel where the coils are and prop it open high enough to use a screwdriver to open the front panel.
Then unscrew the three screws on the inside of the top panel, then open the oven door and you will see 4 screws across the bottom of thefront control board panel and two more on each side of the sides of the panel facing straight up. Unscrew those 6 screws and then pull the front control panel forward and out. You might need something or someone to hold the panel, I just let the wires hold the weight, but not highly recommend. Then pull the switch knob off and behind it there are two little bitty screws that hold the switch in place. Unscrew them and pull the switch out of its place. I put the new switch close to the old one and just used the needle nose pliers to unplug one wire at a time and plug it in on the same place as the old one.
Then screw the itty bitty screws in the front that hold the switch in place and put tbe knob back on. Reposition the front panel back into place abs screw in the 9 screws removed for disassembly. Now would be a good time to clean under the burner panel if you haven’t done so yet ( it gets pretty nasty under there). Then put your burner top back down into place and turn your breaker back on. You can either test with your multi meter or like I did, just put the burner on high and watct the coils glow. Such a beautiful sight. Easy fix.
Was this helpful?
Thank you for voting!
drwer slide under stove broke off.
3 of 4 people found this instruction helpful.
  • paul from sewell, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
recieved part the next day. looked different but I followed instructions and the part worked perfect.
Was this helpful?
Thank you for voting!
old drip pans rusted
3 of 4 people found this instruction helpful.
  • noreen from torrington, CT
  • Really Easy
  • Less than 15 mins
I unplugged the burner, lifted the old drip pan out, put new drip pan in, plugged burner in. The stove looks brand new and it took less than 2 minutes.
Was this helpful?
Thank you for voting!
aged burner bowls
3 of 4 people found this instruction helpful.
  • Louis from Sandwich, MA
  • Really Easy
  • Less than 15 mins
I just removed the range elements and old bowls, placed the new bowls into the range top, and inserted the heating elements. What surprised me was the quickness in filling the order. I had the new parts the next day! Great!
Was this helpful?
Thank you for voting!
Broiler element was bad
3 of 4 people found this instruction helpful.
  • David from LENOIR CITY, TN
  • Easy
  • 15 - 30 mins
  • Nutdriver
1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.
Was this helpful?
Thank you for voting!
burner not work
3 of 4 people found this instruction helpful.
  • SILVIA from Midlothian, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la e stufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.
Was this helpful?
Thank you for voting!
front lift burner not working and surface light on with everything off
2 of 2 people found this instruction helpful.
  • kevin from GAYLORD, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .
Was this helpful?
Thank you for voting!
Bake element shattered while cooking coating everything inside with a fine white dust
2 of 2 people found this instruction helpful.
  • Greg from Virginia Beach, VA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
First I searched for the part here and I had a slightly hard time finding the correct element on the site.
Then I read the comments of the others and the issues they faced.
I unplugged the range and pulled it out a bit from the wall. I then removed the two screws that hold the element in place and put them where I would not lose them. Then I gently maneuved the element out and placed a clothespin on each of the wires to keep them from going back in and then disconnected the wires from the element using a pair of needlenose pliers.

At this point I had to gently bend the new element back into shape as it had been bent during shipping. Then I connected the wires and slid the element into place and installed the two screws.

Double checked to make sure everything was ok plugged in the range, said a quick prayer and set the temperature to 300. When it got to 300 the element shut off and I was happy that the element did not take any other parts with it.
Was this helpful?
Thank you for voting!
Electrode burnt off on left side
2 of 2 people found this instruction helpful.
  • Kenneth from Wisconsin Rapids, WI
  • Easy
  • 15 - 30 mins
  • Nutdriver
First I removed the five screws that hold the
element in place and pulled the element out
about 3 inches and disconnected the two wires
and hooked a piece of wire on the leads to make sure they did not fall behind the cabinet.
Then I connected the new element to the lead
wires and removed the piece of wire and secured the new element in place with the mounting screws. Took about 25 minutes to remove and replace.
Was this helpful?
Thank you for voting!
Oven temp wouldn't regulate.
2 of 2 people found this instruction helpful.
  • Ronald from Crumpler, NC
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Followed the directions!
Was this helpful?
Thank you for voting!
Stove was not getting enough power.
2 of 2 people found this instruction helpful.
  • Nathan from Wells, ME
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),r ed] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.
Was this helpful?
Thank you for voting!
just needed new GE burner bowls
2 of 2 people found this instruction helpful.
  • Jacqueline from E WENATCHEE, WA
  • Very Easy
  • Less than 15 mins
Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.
Was this helpful?
Thank you for voting!
Replace Thermostat
2 of 2 people found this instruction helpful.
  • Russell from Morgantown, WV
  • Really Easy
  • Less than 15 mins
  • Socket set
Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and scr ews. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.
Was this helpful?
Thank you for voting!
Oven drawer open and close incorrectly
2 of 2 people found this instruction helpful.
  • James from Goldsboro, NC
  • Easy
  • Less than 15 mins
  • Screw drivers
First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens a nd closes smoothly.
Was this helpful?
Thank you for voting!
All Instructions for the JCBP35SK2SS
106 - 120 of 474