- Home
- JCBP35SK2SS
- Instructions
JCBP35SK2SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broiler shorted out looked like a 4th of july sparkler.
5 of 6 people
found this instruction helpful.
-
Warren from Killeen, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Ordered on Tues got part on Thurs used a nut driver removed 2 screws holding element in top of oven,then removed the 3 screws holding the element and thermostat to rear of oven pull about 3 inches of slack, removed the blade plugs from element placed them on the new element and assembled it. Took abou 30Min. Easier if you remove the oven
... Read more
door!
Read less
Was this helpful?
Thank you for voting!
surface burner switch was burned
5 of 6 people
found this instruction helpful.
-
abbas from redmond, WA
- Really Easy
- More than 2 hours
-
Nutdriver, Screw drivers
After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove t
... Read more
he swith assembley from the front panel.
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
Read less
Was this helpful?
Thank you for voting!
Shorted the control panel changing bulb without shutting off power dumbass
5 of 6 people
found this instruction helpful.
-
Stephen from BELLINGHAM, MA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Replaced control panel after removing original control panel facing with heat gun and Wala
Other Parts Used:
Was this helpful?
Thank you for voting!
GE oven showed "F2" error code and was over-heating
5 of 6 people
found this instruction helpful.
-
Kyle from AURORA, CO
- Really Easy
- 30 - 60 mins
-
Nutdriver
I am not the handiest person in the world, and this repair was easy even for me. If you suspect that the temperature sensor is the problem, do yourself a favor and buy this inexpensive replacement part and install it yourself prior to calling a professional who will charge a service fee just for checking it out. Pull your oven out from
... Read more
the wall so you can access the back. Unscrew the small nuts on the back to remove the sheet metal cover. Find the wire that goes to the sensor and unplug the plastic coupling. In the oven, unscrew the one nut that secures the sensor to the back wall of the oven. Pull the broken sensor out and replace it with the new sensor. Feed the wire through to the back and plug the new sensor into the same wire that was just disconnected. Reinstall all of the nuts. Do a "test cook" on some frozen food to ensure that the temperature seems correct (i.e., does it cook as expected in the recommended amount of time). The actual repair takes less than five minutes. I put "30-60 minutes" to account for unplugging the oven, pulling it out, removing the screws, replacing the screws, pushing it back in, and testing the temperature.
Read less
Was this helpful?
Thank you for voting!
temp sensor in oven was failing.
4 of 4 people
found this instruction helpful.
-
Chad from FRANKLIN, NC
- Easy
- 15 - 30 mins
-
Nutdriver
I picked the least expensive and most likely issue with our oven that was not indicating a correct oven temperature. I am sure with a 15+ year appliance that the circuitry is on its way out but wanted to give this a try to avoid a new appliance purchase. Oven pre-heat setting takes much longer to finish with the age of the oven. However,
... Read more
after the new sensor the oven will maintain a more even temperature for the cycle.
Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.
At best a temporary fix for a an appliance this old.
Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.
At best a temporary fix for a an appliance this old.
Read less
Was this helpful?
Thank you for voting!
Oven control panel shorted while remove a broken lightbulb from the oven
4 of 4 people
found this instruction helpful.
-
Terry from SEATTLE, WA
- Very Easy
- 30 - 60 mins
-
Nutdriver, Pliers
I removed the new control panel from its packaging and noticed that the button overlay was not included. I grabbed a putty knife and carefully loosened the adhesive on the old panel and was able to apply it to the new control panel. After installing it I looked up the number of my old panel on the included paperwork and simply entered the
... Read more
“profile” number after powering up the new one and It worked perfectly. I was very relieved to not have to buy a new range!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven Wouldn't Heat
7 of 13 people
found this instruction helpful.
-
Russell from Yuma, AZ
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Replaced
Was this helpful?
Thank you for voting!
Front Large Most Powerful Burner's Block had broken so it didn't heat
4 of 4 people
found this instruction helpful.
-
Martin from plainfield, CT
- Really Easy
- 30 - 60 mins
-
Pliers
This electric stove has a lift up top which I lifted to get at the block and follow the wire back to the terminal at the back of the the stove. I removed the 5 small lag screws holding the back in place, removed the backing followed the wires back to where they connected in the Stove On/Off Control, disconnected the two wires from the co
... Read more
ntrol and then laid the new part in place rethreading and reconnecting the wires. I reinstalled the block and ran a test to ensure the burner operated correctly. After successful testing I disconnect the old block holder by removing the small lag screw, replace it with a new one that came with the replacement terminal block. I then inserted the block into the new holder carefully rolled up the excess wire and wrapped it in a couple of places with electrical tape and also secured it to the side of the stove, out of the way of operation with electrical tape, put the top down, plugged it back in and put it back in place. All told the repair took about 40 minutes. I was impressed with the speed of delivery, the quality of the product, the instructions for installation and the added bonus of getting a terminal block holder as part of the repair kit! Thank You for making me look like a genius!
Read less
Was this helpful?
Thank you for voting!
The broil element was burned through
4 of 4 people
found this instruction helpful.
-
Reza from Scottsdale, AZ
- Easy
- 15 - 30 mins
-
Wrench set
First thing I unplugged the range. Then I unscrewed 4 screws in the back of the stove to take the back cover off. Then inside the oven, I unscrewed three screws to lossen the element. Then disconnected the two wires from the element.
Then replaced the old element with the new one going exactly backward as mentioned above finis ... Read more hing with plugging the range.
Then replaced the old element with the new one going exactly backward as mentioned above finis ... Read more hing with plugging the range.
Read less
Was this helpful?
Thank you for voting!
F2 Error on Display
4 of 4 people
found this instruction helpful.
-
Tom from FORNEY, TX
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back pa ... Read more nel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.
Swapping the sensor was extremely easy. You take off the back pa ... Read more nel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.
Read less
Was this helpful?
Thank you for voting!
Oven Temp. went too high and the door locked. Burnt the food
4 of 4 people
found this instruction helpful.
-
Nathan from BILLINGS, MT
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws
... Read more
off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.
Read less
Was this helpful?
Thank you for voting!
F2 fault code kept appearing on oven
5 of 7 people
found this instruction helpful.
-
emmett from rocky mount, NC
- Easy
- 15 - 30 mins
-
Nutdriver
Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Thea
... Read more
ded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.
Read less
Was this helpful?
Thank you for voting!
Burner at full red hot power despite setting
4 of 4 people
found this instruction helpful.
-
Matt from TAZEWELL, VA
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
After removing power from the range, I pulled the unit out for better access to the rear. I carefully pulled all four knobs off the front of the control panel. Next, using a short phillips screwdriver, I removed two screws from the front bottom of the control panel. On the rear of the control panel, there are four screws to loosen, now th
... Read more
e whole panel is free to remove toward the front of the unit. The burner switches are held onto the panel with two screws that are located on the front under where the knob had been. The wires are all connected to the switch with crimp type connectors. These are on tight, but can be removed carefully with pliers. Before doing so, I took a picture on my phone to ensure I replaced the wires in the correct order. Everything goes back together in reverse order. This is a good time to clean behind and under the whole stove. The whole process took around 20 minutes.
Read less
Was this helpful?
Thank you for voting!
One of the drawer supports broke off
5 of 7 people
found this instruction helpful.
-
John from Sandy Hook, CT
- Really Easy
- Less than 15 mins
-
Nutdriver
I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it com
... Read more
plete.
Read less
Was this helpful?
Thank you for voting!
terminal was broken due to maney uses
4 of 5 people
found this instruction helpful.
-
Emmett J from Winchester, VA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
unscrew the terminal block,pulled the old wires out,installed the new wires installed the new block
Was this helpful?
Thank you for voting!