- Home
- JCBP35SK2SS
- Instructions
JCBP35SK2SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
It was burned out
2 of 2 people
found this instruction helpful.
-
lan from SANTA CLARA, CA
- Really Easy
- Less than 15 mins
-
Socket set
I just follow Steve's Installation Vidio. My range works.
Thanks Steve
Thanks Steve
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people
found this instruction helpful.
-
Gerald from WINTERVILLE, GA
- Very Easy
- Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Oven could not be turned off once settings were turned on except by unplugging hookup.
2 of 2 people
found this instruction helpful.
-
Charles from BENNETTSVILLE, SC
- Really Easy
- 30 - 60 mins
-
Nutdriver
Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.
Was this helpful?
Thank you for voting!
Surface burner stopped working & light indicator remained on
2 of 2 people
found this instruction helpful.
-
Cynthia from BALDWINSVILLE, NY
- Very Easy
- 15 - 30 mins
-
Screw drivers
It took my son very little time to install control switch. Using a screw driver he removed the back panel directly behind burner units & replaced the control switch. Very easy.
Was this helpful?
Thank you for voting!
Stove overheated with an F2 error
2 of 2 people
found this instruction helpful.
-
Richard from PHOENIX, AZ
- Easy
- 15 - 30 mins
-
Nutdriver
Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Was this helpful?
Thank you for voting!
Oven would shut down while baking. Stove top would work.
2 of 2 people
found this instruction helpful.
-
Tom from ELIZABETHTON, TN
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certai
... Read more
n areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..
The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.
The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.
Read less
Was this helpful?
Thank you for voting!
Inner glass broke
2 of 2 people
found this instruction helpful.
-
Mark from OLIVE BRANCH, MS
- Easy
- 30 - 60 mins
Removed torx screws for door handle as well as torx screws for both hinges to separate the door halves to extract broken glass and to install new glass panel. Other reviews said not to remove hinge screws, however I had no problem reinstalling them.
Was this helpful?
Thank you for voting!
Just didn't work no pwr to it
2 of 2 people
found this instruction helpful.
-
Jerry from HOPEWELL, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.
Was this helpful?
Thank you for voting!
Defective switch
2 of 2 people
found this instruction helpful.
-
Mary from EDENTON, NC
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Replaced element control switches
Was this helpful?
Thank you for voting!
Oven would not get come up to temperature
2 of 2 people
found this instruction helpful.
-
Arthur from INDIANAPOLIS, IN
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair ac
... Read more
tions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!
Read less
Was this helpful?
Thank you for voting!
element burned out
2 of 2 people
found this instruction helpful.
-
raleigh from gresham, OR
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
couldn't get exact fit--out of production. mounting bracket at back of range for new element too small. took bracket off old element. cut down bracket on new element with tin snips, drilled holes thru it and old bracket and screwed together. at this point the new element was to long & touched oven door. removed spacers that came wit
... Read more
h new element (used old support to attached to roof of oven) and pried elements apart (which made element wider & shorter). working good.
Read less
Was this helpful?
Thank you for voting!
Bake element melted.
2 of 2 people
found this instruction helpful.
-
Allen from HENRICO, NC
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Would have helped it I knew the push on terminals of the bake element were visible and accessible to slide the terminals on from the back side of the stove in the beginning. There is not enough slack in the the terminal wires to connect them from the oven side, so you will have to open the back panel to retrieve a wire anyway. SO, CONNECT
... Read more
THE BAKE ELEMENT TO THE OVEN WALL FIRST ! Then, open the back panel of the stove and simply slide the terminals on the exposed slide terminals of the bake element.
Read less
Was this helpful?
Thank you for voting!
Was burned out
2 of 2 people
found this instruction helpful.
-
BRINDIA from DOVER, TN
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Took back off and replaced.
Was this helpful?
Thank you for voting!
Terminal block connectors worn out wasn’t making a good connection with the stove top burner
2 of 2 people
found this instruction helpful.
-
Lance from HAHIRA, GA
- Really Easy
- 30 - 60 mins
-
Nutdriver
Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.
Was this helpful?
Thank you for voting!
Broiler element burned out in the oven.
2 of 3 people
found this instruction helpful.
-
Emmett from Buffalo, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
The only hard thing was contorting my old beat up body and joints long enuff to reconnect the 2 wires and oven heat sensor and put in 6 screws with a 1/4" nut driver. I did remover the oven door and that made it much easier for me.
Was this helpful?
Thank you for voting!