EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCB560DF1WW General Electric Range - Instructions

All Instructions for the JCB560DF1WW
91 - 105 of 168

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner didn't work, using a test light showed only one side was hot.
0 of 1 people found this instruction helpful.
  • Kathleen M from Nampa, ID
  • Really Easy
  • Less than 15 mins
  • Screw drivers
took the back panel off the range, took the 2 screws holding the switch in place, took the old switch out, marked the wires took the wires off and clipped them onto the new switch, put the new switch into the switch plate, replaced the screws put on the knob, put the panel back on the range. rolled the range back into it's place. turned the buner on to check if it worked. It did so we were done.
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people found this instruction helpful.
  • Roscoe G from ROCHESTER, NY
  • Very Easy
  • Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
light keep burning out in oven.
2 of 8 people found this instruction helpful.
  • john from Mc Kees Rocks, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid door back on and done. 30 minutes at most.
Was this helpful?
Thank you for voting!
Burner not heating.
1 of 5 people found this instruction helpful.
  • Jack from Greensboro, GA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Isolated to control switch.

Replaced
Was this helpful?
Thank you for voting!
eye wouldnt come on
0 of 2 people found this instruction helpful.
  • daniel from valentines, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this helpful?
Thank you for voting!
burner was inoperative
0 of 2 people found this instruction helpful.
  • bryan from cocoa, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
Was this helpful?
Thank you for voting!
burners would go to full high heat& not reduce down.
  • Sandra from Chipley, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench set
Hubby did the job..all went well except for the arthritis & having to bend pull stove out from wall ,pushing back..ha-ha.
Was this helpful?
Thank you for voting!
Large eye would over heat when was on med. settings
  • LEE from ROME, GA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I unpluged the stove pulled it out and took the 6 screws off the back to get to the switch. Around front take knob off and removed the two screws holding the swich in place and pulled it out the back. Pulled one wire at a time off of the old switch and replace on the new switch. Nothing to it had it done in just a few mins.
Was this helpful?
Thank you for voting!
Convection fan came loose from shaft
  • Thomas from Albuquerque, NM
  • Easy
  • 15 - 30 mins
  • Socket set
Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the rep lacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."
Was this helpful?
Thank you for voting!
Burner not heating
  • Henry from Norwich, CT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.
Was this helpful?
Thank you for voting!
plastic adapter was broken on end of the block kit
  • Michael from West Monroe, LA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
unplugged old block from both sides, ran new wire and plugged new wire to both ends and presto it worked, thanks for making it easy to fix. Thanks- Michael J Dumas
Was this helpful?
Thank you for voting!
Front and back burners not getting hot
  • Fred from De Leon, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Followed the video supplied with the email on the parts order form. Biggest problem was pulling the range out from the wall, the repairs went without a hitch. The PartsSelect video was a great help showing the short cut to getting the new wires in by using the old wires as a pull wire.
Was this helpful?
Thank you for voting!
Drip bowls were rusty and not original GE. Small burners never fit quite right and rocked unevenly.
  • Ian from Casselberry, FL
  • Easy
  • 15 - 30 mins
Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in openin g and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.
Was this helpful?
Thank you for voting!
Burner switch shorted out
  • Robert from Blairsville, GA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
This burner is on a Monarch wood and electric range. The 8in burner shorted out and fried the switch. I had to remove the cover over the switch's. I marked each lead with paper and stapled the paper to the leads. When the switch came in I just had to reattach the leads.
Was this helpful?
Thank you for voting!
Burner went to high heat at any setting
  • Robert W from Whitehall, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Thanks to Partselect's instructions the repair went very easy. When I was done and the wife finished cleaning the sides of the stove and the floor behind it, I was surprised after I plugged the stove back in and noticed the clock was only 18 minutes off! Awesome company to deal with, Thanks!
Was this helpful?
Thank you for voting!
All Instructions for the JCB560DF1WW
91 - 105 of 168