EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCB560DF1WW General Electric Range - Instructions

All Instructions for the JCB560DF1WW
76 - 90 of 168

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner terminal block was worn out
1 person found this instruction helpful.
  • Mario from RENO, NV
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the b urner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you
Was this helpful?
Thank you for voting!
Oven door gasket was damaged and leaking
1 person found this instruction helpful.
  • Kerry from Sheboygan, WI
  • A Bit Difficult
  • 1- 2 hours
  • Socket set
I watched the repair video on YouTube and followed his instructions as much as possible. Went pretty well as I thought it would be harder. I’m pretty handy so, I was pleased.
Was this helpful?
Thank you for voting!
on off switch smoked and smelled hot
1 person found this instruction helpful.
  • john from MILROY, PA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
standard procedure, very simple
Was this helpful?
Thank you for voting!
burner was not heating
1 person found this instruction helpful.
  • lucille from HAPPY CAMP, CA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
unplug it and plug the new one in
Was this helpful?
Thank you for voting!
control switch had stopped working, burner wouldn't work properly
1 person found this instruction helpful.
  • Ruth from JACKSON, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
took out a couple of screws and replaced with new switch, plugged in switch wires. very easy
Was this helpful?
Thank you for voting!
Burnt Terminal Block
1 of 2 people found this instruction helpful.
  • Bayani P. from DALY CITY, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people found this instruction helpful.
  • Louis from LEAGUE CITY, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Easy
Was this helpful?
Thank you for voting!
Hot burner light lens broke off.
1 of 2 people found this instruction helpful.
  • Charles from NEKOOSA, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.
Was this helpful?
Thank you for voting!
Surface element switch failed
1 of 2 people found this instruction helpful.
  • William W. from Seattle, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Top front sloping sheet metal panel with all controls and plastic end caps has to come off. Need 2 people, one to hold it while other replaces switch. Problem was getting screw holes on bottom ends lined up and cuts from sheet metal edges. Ten minutes to get it apart, 40 to get it back together. New switch works fine.
Was this helpful?
Thank you for voting!
part replacement
1 of 2 people found this instruction helpful.
  • charles from st marys, GA
  • Really Easy
  • Less than 15 mins
pull out, push in
Was this helpful?
Thank you for voting!
rusted drip bowls
1 of 2 people found this instruction helpful.
  • Caren from Choctaw, OK
  • Really Easy
  • Less than 15 mins
I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.
Was this helpful?
Thank you for voting!
Missing screw to range door handle
1 of 2 people found this instruction helpful.
  • Stanley from TRENTON, NJ
  • Very Easy
  • Less than 15 mins
The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.
Was this helpful?
Thank you for voting!
Drip bowls had deteriorated after years of use
1 of 2 people found this instruction helpful.
  • Stuart from UNION SPRINGS, NY
  • Very Easy
  • Less than 15 mins
Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes
Was this helpful?
Thank you for voting!
electric burner shorted out and fried the switch
1 of 2 people found this instruction helpful.
  • David from Greenwood, IN
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Removed two screws holding the housing in place and loosened two more on the back it order to free it. Switch was held i place with two screws, removed those. Transfered wires one by one on the new switch, which was identical OEM part, and replaced the screws. VERY simple.
Was this helpful?
Thank you for voting!
Water dumped over in in my overhead microwave, which dripped down on, & shorted out a burner switch.
1 of 3 people found this instruction helpful.
  • Deanna from Buckeye, AZ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.
Was this helpful?
Thank you for voting!
All Instructions for the JCB560DF1WW
76 - 90 of 168