- Home
- JBS86SP3SS
- Instructions
JBS86SP3SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
eye wouldnt come on
0 of 2 people
found this instruction helpful.
-
daniel from valentines, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this helpful?
Thank you for voting!
burner was inoperative
0 of 2 people
found this instruction helpful.
-
bryan from cocoa, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
after extremely fast
service from partselect thank you
Was this helpful?
Thank you for voting!
F2 error code
0 of 2 people
found this instruction helpful.
-
jud from gatesville, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's tha
... Read more
t easy. No more f2 been working like a champ!!!
Read less
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people
found this instruction helpful.
-
Roscoe G from ROCHESTER, NY
- Very Easy
- Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Burner not heating.
1 of 5 people
found this instruction helpful.
-
Jack from Greensboro, GA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Isolated to control switch.
Replaced
Replaced
Was this helpful?
Thank you for voting!
Burner Would Not Turn Off
-
BILLY from WEBSTER, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver
Replace control switch
Was this helpful?
Thank you for voting!
oven temp. was not what setting called for
-
John from Acme, WA
- Easy
- 1- 2 hours
-
Nutdriver
turned oven off, pulled oven out from wall, removed back of oven, unscrewed sensor from oven replaced with new sensor, put back on, turned power to oven on, tried oven at 425, my temp. gage and the oven temp matched. a very easy fix.
Was this helpful?
Thank you for voting!
oven not warming, f2 indicating overheat
-
David from Lisle, IL
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a cham
... Read more
p. Took 5 minutes.
Read less
Was this helpful?
Thank you for voting!
Oven temperature was low when reading was correct
-
Orion from Vancouver, WA
- Really Easy
- Less than 15 mins
-
Nutdriver
First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the b
... Read more
ack top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!
Read less
Was this helpful?
Thank you for voting!
Flashing F2 and erratic temperature readings.
-
Kenneth from Salem, OR
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.
Was this helpful?
Thank you for voting!
My upper oven, lower heating element burnt out .
-
John from Salem, NH
- Really Easy
- 15 - 30 mins
-
Nutdriver
Shut off power to oven. Removed upper oven door and cooking racks. Removed 2, 1/4" bolt, pulled element away from oven back wall and unplugged the 2 wires that went into the heating element and removed the element. Reinstalled the new element by plugging in the 2 wires to the element, pushing the wires back through the back of the oven an
... Read more
d reinstalled the 2, 1/4" bolts. Reinstalled the cooking racks and oven door. The complete from start to finish time took about 15 minutes.
Read less
Was this helpful?
Thank you for voting!
Oven lights were burning out regularly
-
Douglas from Thornton, CO
- Really Easy
- 15 - 30 mins
-
Socket set
Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixtu
... Read more
re back into place and screwed the housing into place.
Read less
Was this helpful?
Thank you for voting!
F2 reading
-
lynn from sunnyside, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Followed the instructions that were sent to me by E-Mail.
Was this helpful?
Thank you for voting!
The oven temperature could not be controlled
-
Keith from Annapolis, MD
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later.
... Read more
Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!
Read less
Was this helpful?
Thank you for voting!
Oven slow to heat up
-
Joe from Harkers Is., NC
- Easy
- 15 - 30 mins
-
Nutdriver
Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had
... Read more
the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.
Read less
Was this helpful?
Thank you for voting!