EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JBS86SP3SS General Electric Range - Instructions

All Instructions for the JBS86SP3SS
76 - 90 of 132

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake and convection cycles quit working after a10 minutes
1 person found this instruction helpful.
  • Stephen from Zachary, LA
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Unbolted temperature sensor from back of oven. Disconnect cable connector. Replaced and reconnected new sensor and bolted back in place. Haven’t had to replace bake element yet, but it’s a major job being this GE Profile oven has the bake element hidden. That’s a new one on me.
Was this helpful?
Thank you for voting!
Element blew hole in self then no power to burner.
2 of 4 people found this instruction helpful.
  • Melvin from Portland, TN
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this helpful?
Thank you for voting!
Not Reaching Temperature above 300 Degrees
1 person found this instruction helpful.
  • Ron from SAN TAN VLY, AZ
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this helpful?
Thank you for voting!
Needed another rack for my oven
1 person found this instruction helpful.
  • Betty J from Anacortes, WA
  • Very Easy
  • Less than 15 mins
Really no repair. Just slid it in my oven and was so happy to have it. It was nice to find just what I needed!
Was this helpful?
Thank you for voting!
shortage in wiring cause the housing to burn out
1 person found this instruction helpful.
  • fred from PALM COAST, FL
  • Really Easy
  • Less than 15 mins
Replaced new light housing.
Thanks to you guys for the prompt response
Was this helpful?
Thank you for voting!
Remove back panel or access sensor, replace sensor and panel
1 person found this instruction helpful.
  • Mike from Glencoe, NM
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Removed back panel, change out sensor
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people found this instruction helpful.
  • Catherine from SEATTLE, WA
  • Very Easy
  • Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap. ... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.
Was this helpful?
Thank you for voting!
Outside portion of Element broken
1 person found this instruction helpful.
  • Tiffany from Lexington, OH
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
First unplug range from electrical outlet!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!
Was this helpful?
Thank you for voting!
Switch broke and stayed on.
1 person found this instruction helpful.
  • Harold from SANGERVILLE, ME
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Shut off breaker, pulled the stove out,unplugged it,removed the knob, removed the screws from back top panel. I unplugged the switch, removed the 2 screws holding it in place. Then exchanged it. Re assembled it.
Was this helpful?
Thank you for voting!
Lower element in the upper oven was not heating.
1 person found this instruction helpful.
  • Bunny from COLUMBIA, SC
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
Prep: You need a 1/4” nut driver to remove the screws in the oven. Approx. $6.00 at the hardware store. Flashlight. Two small chip clips or clothespins.

1. Turn off power at the breaker.
2. Remove oven rack.
3. Use nut driver to remove screws and pull element to expose wires. Attach chip clips to each wire to prevent the wires from slipping behind. Remove old element.
4. Plug in the new element and make sure secure. Turn on breaker to test.

While this was a simple repair, turned out the element was not my problem. I needed a new relay board. The relay board part is not readily available, so you have to dig around the web to find one.
Was this helpful?
Thank you for voting!
main banner was burnt out.
1 person found this instruction helpful.
  • clinton from SAN JOSE, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
simply followed the instructions. I marked each wire and were to go on new burner. put the burner back in place and it worked.
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people found this instruction helpful.
  • Louis from LEAGUE CITY, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Easy
Was this helpful?
Thank you for voting!
Water dumped over in in my overhead microwave, which dripped down on, & shorted out a burner switch.
1 of 3 people found this instruction helpful.
  • Deanna from Buckeye, AZ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.
Was this helpful?
Thank you for voting!
oven was not getting up to temp
0 of 1 people found this instruction helpful.
  • walter from townshend, VT
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.
Was this helpful?
Thank you for voting!
F2 error when oven was heating up, along with a beeping noise and then it shut off
0 of 1 people found this instruction helpful.
  • Lori from Paris, TN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!
Was this helpful?
Thank you for voting!
All Instructions for the JBS86SP3SS
76 - 90 of 132