EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JBS034N1 General Electric Range - Instructions

All Instructions for the JBS034N1
106 - 120 of 355

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven would not get hot when on the BAKE setting
1 of 2 people found this instruction helpful.
  • Kathy from Lincoln Park, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Four screws and two wires.
Was this helpful?
Thank you for voting!
Element died
1 of 2 people found this instruction helpful.
  • John from Mount Airy, MD
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
The hardest part was working in the oven.

Turn off power
Open Oven Door, remove racks
Remove two mounting screws with nut driver.
Slide the element out to expose the wire connections.
Remove the screws and pull the element out.
Place the new element in oven.
Clamp on to each of the terminals wit h vice grips to keep from bending the element and install the screws.
Slide the element back into place and put the two mounting screws back in.

Put the racks back in and turn on the power and test. You may get a little smoke off the new coil.

Like I said the hardest part is leaning into the oven to attach the screws, do not sit on the oven door.
Was this helpful?
Thank you for voting!
Bad Bake Element
1 of 2 people found this instruction helpful.
  • John from Spring Grove, PA
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
The bake element in my 17 year old GE free standing electric range became defective. This element has 2 terminals -- black (240V) and white (neutral). While removing the element from the range, a 2nd black wire was pulled out of the back of the oven. This wire had a bare terminal connection and apparently had been loose behind the oven shell for all these 17 years. Inspection of this wire showed it carried 115V. I wrapped this wire with electrical tape and reinserted it into the insulation behind the oven shell.
Was this helpful?
Thank you for voting!
Oven element was shorted out
1 of 2 people found this instruction helpful.
  • KEVIN from WAUSEON, OH
  • Really Easy
  • Less than 15 mins
  • Pliers
No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few second s element got hot, job done!
Was this helpful?
Thank you for voting!
Oven took long time to reach desired temp. Element sparkled and burned up.
1 of 2 people found this instruction helpful.
  • Joe from Raleigh, NC
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the ove n on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.
Was this helpful?
Thank you for voting!
old heating element burned out
1 of 2 people found this instruction helpful.
  • Lee from Franklin, TN
  • Easy
  • Less than 15 mins
  • Pliers
unplugged oven. removed oven racks.Disconnected old unit. Installed new unit. Very very simple
Was this helpful?
Thank you for voting!
Bake unit had burned out
1 of 2 people found this instruction helpful.
  • Margaret from Brookland, NY
  • Really Easy
  • Less than 15 mins
  • Socket set
With great ease. Only thing I would have appreciated was knowing the size ofvthevrequired socket wrench. Otherwise it was easy and fun as the instructions were crystal clear.
Was this helpful?
Thank you for voting!
bake element burned out
1 of 3 people found this instruction helpful.
  • PIPER from DECATUR, GA
  • Really Easy
  • Less than 15 mins
  • Socket set
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.
Was this helpful?
Thank you for voting!
Burner only worked on High and very low temperature setting.
2 of 6 people found this instruction helpful.
  • William from Duvall, WA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.
Was this helpful?
Thank you for voting!
Switch - and the connection wire to the burner
2 of 6 people found this instruction helpful.
  • andrew from langdon, ND
  • Easy
  • 30 - 60 mins
  • Pliers
First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch ) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.
Was this helpful?
Thank you for voting!
Bale element in oven failed
0 of 1 people found this instruction helpful.
  • Dale from Savage, MN
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Open oven door about 3 inches - then holding on the door on either side - pull up and door slides off - put it aside - this is to make it easy for you to work inside oven compartment - at rear of oven where the element goes into the back wall - there are two nuts to remove - I did not have a nut drive so used a pliers (GE could have put s lots in the nuts so one would just need a screwdriver) - pull element forward - there are wires attached to the 2 ends of the element - remove with screw driver - element is off - get new part from PartSelect -(and must say pleased with their service) - and reverse above procedure.
Was this helpful?
Thank you for voting!
Burner not heating properly
0 of 1 people found this instruction helpful.
  • Stephen from Kokomo, IN
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and re move the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.
Was this helpful?
Thank you for voting!
My baking element had broken
0 of 1 people found this instruction helpful.
  • Elyse from Mankato, MN
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
My sons helped with that. They had to use a pliers to remove the old screws (did not have to notches). After that they they removed the element. Then the wires had to be disconnected (after we unplug the oven from the main power source. Then the wires were connected to the new heating unit. We only got one screw in so far will work o n getting the second one in when they return tomorrow. I did turn on the oven and it works!!!

Thank you to the nice young man that helped me on the phone.
Was this helpful?
Thank you for voting!
Replace burned out oven bake element...
0 of 1 people found this instruction helpful.
  • Chuck from Plymouth, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver
First off the part was easy to find on Partselect...

Second point... ordering was easy and shippment was fast thanks to Partselect...

Replacezment was fairly easy useing a Nut driver and a pair of pliers...took about 40 minutes.

Thank you Partselect...

Chuck
Was this helpful?
Thank you for voting!
not heating correctly
0 of 1 people found this instruction helpful.
  • Elizabeth from Roswell, GA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Turned off circuit. Unscrewed old element. Connected new element and screwed it in. Worked like a charm. It shipped very quickly. Could not be more satisfied; total repair: $30 and prevented me from buying a new oven; satisfaction: priceless.
Was this helpful?
Thank you for voting!
All Instructions for the JBS034N1
106 - 120 of 355