GF950ND2 Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not light and gas would not come through.
1 person
found this instruction helpful.
-
Jesse from Haines City, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I unplugged the stove then pulled the disconnected the wires that controled the igniter. I took the two screws off that held the igniter to the pilot port. I hand to cut the wires on the new igniter to some-what match the lenght of the broken igniter. Then I cut the connectors from the old part and used the fire resistant wire nutes tha
... Read more
t where included with the new igniter and connected it all. Put all the screws in tight, double checked every thing. Finally I plugged it in and it was working.
Read less
Was this helpful?
Thank you for voting!
replaced oven igniter
1 person
found this instruction helpful.
-
Gary from Waco, TX
- Easy
- 15 - 30 mins
-
Screw drivers
Removed racks,oven bottom(2 screws) and heat deflecter. Slide heat sleeves 10 inches away from old igniter. Cut wires one inch longer than the length of the heat sleeves, from the old igniter. Cut the new wires to match old wire length. Replace old igniter. Slide sleeves up to new igniter. Wire nut ends-done deal. It was hard working ove
... Read more
r the oven door,but I am old. Good luck
Read less
Was this helpful?
Thank you for voting!
Oven would not ignite
1 person
found this instruction helpful.
-
Matthew from ERDENHEIM, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The repair was simple - I first needed to test the original igniter with a circuit tester. Once I determined that the part was bad, I simply removed it and replaced it with a new one from Partselect. It was a matter of simply unplugging a few wires and splicing the new igniter in with wirenuts. Fairly simple.
Was this helpful?
Thank you for voting!
Oven would not heat up
1 person
found this instruction helpful.
-
Dean from Tupper Lake, NY
- Easy
- 15 - 30 mins
-
Screw drivers
First I removed the two screws that held the element in place.I then pulled the element out and cut the wires.I used wire nuts to put the new wirers on and put it back in place with the two screws.I tried it and it worked perfect.
Was this helpful?
Thank you for voting!
oven took longer and longer to ignite ,then just stopped.
1 person
found this instruction helpful.
-
marc from troy, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took out the cove plate inside oven. romoved old igniter load.cutt and stripped new wire to new ignighter , using ceramic wire nuts supplied. reinstalled all and voila. it's as good as new. PS just for safety sake always unplug appliance from power.
Was this helpful?
Thank you for voting!
OVEN WOULD NOT COME ON
1 person
found this instruction helpful.
-
david from SLIDELL, LA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.
Was this helpful?
Thank you for voting!
Oven Would Not Light
1 person
found this instruction helpful.
-
Michael from Houston, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.
Was this helpful?
Thank you for voting!
Oven would not light
1 person
found this instruction helpful.
-
Stephen from Pittsburgh, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!
Was this helpful?
Thank you for voting!
GAS OVEN WON'T LIGHT.
1 person
found this instruction helpful.
-
stephen from LIVERPOOL, NY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER
... Read more
AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't light
1 person
found this instruction helpful.
-
JERRY L from PIPER CITY, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?
Was this helpful?
Thank you for voting!
Oven glows but won't ignite
1 person
found this instruction helpful.
-
John from MANASSAS, VA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.
Was this helpful?
Thank you for voting!
Bad igniter in switch
1 person
found this instruction helpful.
-
William from SPENCERPORT, NY
- Very Easy
- 15 - 30 mins
-
Screw drivers
Removed 4 burner knobs. Unscrewed 6 phillips head screws on manifold.Pulled back manifold enough to remove switch. Removed the Two wires from switch and hooked them up to the new switch. Slid new switch on to shaft and in reverse order, reasembled manifold, screws and knobs.
Was this helpful?
Thank you for voting!
replaced theoriginal power cord.
1 person
found this instruction helpful.
-
Blanca from Union City, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers
moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.
Was this helpful?
Thank you for voting!
Longer time for oven to preheat. Replacing oven igniter solved my issue
1 person
found this instruction helpful.
-
Winfred from CARSON, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
First thing is I looked for videos on how to replace oven igniter to get an idea. Unplug AC cord and turn off gas valve.On my model I was not able to figure out how to remove oven door. You can still work around it without removing. Inside the oven, remove bottom cover. Remove 2 screws located in rear corners. After removing oven bottom c
... Read more
over, next is a burner cover. Remove 2 screws located toward front of oven using a nutdriver or socket. After removing burner cover , you will find oven igniter. Now remove bottom drawer. This is why its a bit difficult for others. Igniter has 2 leads. Laying down on the floor and reaching in to follow-identify where the 2 leads go to. Using same nutdriver or socket remove 2 screws that hold up the igniter. I cut the leads from the base of the old igniter so you will have some slack to work on when you reconnect the wires underneath. Install new igniter, run leads same way.Strip back about 3/8 in. wire, twist leads to proper wires and twist on ceramic wire cap that is provided. Make sure no bare wires are exposed! Now you can test.
Read less
Was this helpful?
Thank you for voting!
oven would not allow gas to flow for igniter to light
1 person
found this instruction helpful.
-
charles from bossier city, LA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since
Was this helpful?
Thank you for voting!