EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GF950ND2 Frigidaire Range - Instructions

All Instructions for the GF950ND2
121 - 135 of 405

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
igniter burned-out, not able to start oven
1 person found this instruction helpful.
  • BETTY from PHILADELPHIA, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
followed directions enclosed.required removal of oven door and old igniter
Was this helpful?
Thank you for voting!
would not light
1 person found this instruction helpful.
  • clayton from rockford, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
open oven door remove bottom of oven then remome the metal cover over the burner to expose the ignighter remove 2 screws that hold it to the bracket. the two wire's that come out of the ignighter run down under the bottom oven pan, i removed the bottom front cover by lifting up and then pulled out, then i could see the wires i removed the wire nuts and pulled old wires off and removed old ignighter. i pulled off the insulator covers from the old one and slid them on the wires of the new ignighter then i fished the wires back down and and attachted them with the wire nuts, then reasembled the rest of the oven. woks great!
Was this helpful?
Thank you for voting!
Oven of gas range not igniting
1 person found this instruction helpful.
  • Hubert from Street, MD
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed lower drawer of oven and base panel of oven. Unplugged stove from outlet. Removed old igniter w/ nut driver (two screws). Disconnected wires (blade connectors) from stove base. Disconnected two-pole plug from oven after removing protective cover in corner.

Install new igniter. You will need to cut existing wires fro m old igniter so that spade and two-pole connectors can be reused. Join these wires with the new ignitor wires using the ceramic wire nuts provided with the new unit.
Directions are also provided with the new igniter.
Was this helpful?
Thank you for voting!
oven would work intermittently
1 person found this instruction helpful.
  • Michael from Chicago, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.
Was this helpful?
Thank you for voting!
Ignition not working
1 of 2 people found this instruction helpful.
  • Ricardo from Stamford, CT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Ins talled new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.
Was this helpful?
Thank you for voting!
Oven would not come on. If it did, it took a long time to heat up.
1 of 2 people found this instruction helpful.
  • Frank from Greenbackville, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed the broiler compartment door by depressing the slide stops inward and pulling the door off. Turned off the breaker to the oven. Used a nut driver to remove the old ignitor ( 2 screws ). Cut the wires off the old ignitor close to the porclin. Measured the new ignitor wires to match up with the old ignitor wires and cut them. St ripped 3/8 " off ends of newely cut wires of the ignitor and used the supplied wire nuts to secure them together. Replaced the new ignitor with the 2 screws. Turned on the oven and a cooking I went.
Was this helpful?
Thank you for voting!
Rear Drawer Glide
1 of 2 people found this instruction helpful.
  • errol from bronx, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Just use flat screwdriver to press on clip and just squeeze it in
Was this helpful?
Thank you for voting!
The front drawer glide broke off so one side of warmer drawer was sagging
1 of 2 people found this instruction helpful.
  • Lamar from Theodore, AL
  • Really Easy
  • Less than 15 mins
After researching on what exactly to call the part, which was a front drawer glide. I found this out by watching the video. It showed me exactly what I needed and what it looked like. I run to the oven to look at the other one, to make sure thats what I needed, and it looked like the part that I needed (mind you I am a female, and not a repair person), so this video helped me out alot. When the part arrived, I knew how to take the drawer out, and easily snapped the little plastic glide in to place, and slipped the drawer back on the gliders, and it worked perfect, so proud of myself, that I done it by myself, with no help from husband. I bragged and bragged on myself with a big pat on my own back, thanks Part Select, I know what to do when it happens again. Its my fault cause it broke, cause I overload the drawer with pots and pans LOL!!! Brenda Dixon
Was this helpful?
Thank you for voting!
Old handle was rusted.
1 of 2 people found this instruction helpful.
  • Teresa from ORMOND BEACH, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Repair was easy. just unscrewed the old handle, holes measured correctly and screwed in the new handle.The only flaw was that it did not come with the two end caps,they have to be bought separately & the handle ends are sharp without them.
Was this helpful?
Thank you for voting!
the oven was slow to light and didn't reach the set temperature
1 of 2 people found this instruction helpful.
  • James from Chicago, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.
Was this helpful?
Thank you for voting!
Oven wouldn't come on
1 of 2 people found this instruction helpful.
  • Arthur L from Huntington, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.
Was this helpful?
Thank you for voting!
Oven wouldn't heat , glow from bottom, and strong smell of gas
1 of 2 people found this instruction helpful.
  • Clayton from Gulf Breeze, FL
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers, Wrench set
First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two sc rews on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.
Was this helpful?
Thank you for voting!
Disgusting Drip Pans
1 of 2 people found this instruction helpful.
  • Randie from Ewing, NJ
  • Really Easy
  • Less than 15 mins
Opened the box, took out the drip pans and the put them on the stove. Wow -- even a techno-challenged person like myself could do this! I ordered these on a Tues. at 2:00 p.m. and received them on Wednesday -- that is a first so thanks for the fast service and they look great! Was non-existent to find them at local appliance stores in the area so thank you for having them.
Was this helpful?
Thank you for voting!
Drawer glides were snapped off
1 of 2 people found this instruction helpful.
  • MICHELLE from STOUGHTON, MA
  • Really Easy
  • Less than 15 mins
The drawer under the oven had been aggravating me for some time. It was titled and did not close right. Finally, I took it out to see what the problem was and noticed that the glides were broken. I googled the model no. of the stove (figuring I would have no luck) and to my great relief was directed to this EXCELLENT site. I ordered the new drawer glides within minutes and they were literally delivered the next day. Snapped right in, fixed, happy!! It's times like this when I can't figure out how we all lived without the internet!
Was this helpful?
Thank you for voting!
One Of The Front Drawer Guides Broke
1 of 2 people found this instruction helpful.
  • RICHARD from WABASH, IN
  • Really Easy
  • Less than 15 mins
Removed the drawer. Inserted the new glide tab into a hole in the side. Inserted the drawer slides in the the glide. Closed drawer--done! Works fine. Probably only 5-10 minutes.
Was this helpful?
Thank you for voting!
All Instructions for the GF950ND2
121 - 135 of 405