EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GF950ND2 Frigidaire Range - Instructions

All Instructions for the GF950ND2
91 - 105 of 405

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
My Oven Was Taking Too Long To Heat Up,I Was Smelling Gas,Which Is The First And Last Warning
1 person found this instruction helpful.
  • John from Manchester, CT
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Simple repair ,unplug unit,cut the 2 wires close to heating element,remove elements 2 screws w/1/4 inch nut driver. Cut and strip 2 wires back about 1/2 inch,be sure to cut wires close to element,wirenut both wires together. Reinstalled element,plug unit back in. Done . . . 12 Minutes,ready to bake a cake. .
Was this helpful?
Thank you for voting!
The ignitor came on with a call for heat but the gas valve did not open
1 person found this instruction helpful.
  • Terry from Tonganoxie, KS
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First turn the thermostat off-cut the wires leading to the ignitor, close to the ignitor side-Remove the two 1/4" monting bracket screws and remove the ignitor install the new ignitor using the same 1/4" screws and reconnect the wires leading into the ignitor, note the polarity is not imp[ortant--use the heat temp-wire nuts provided--clo se the door and call for heat the gas valve is working fine now....
Was this helpful?
Thank you for voting!
Oven wouldn't heat
2 of 4 people found this instruction helpful.
  • M. Nicole from La Mirada, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I reattached the new piece. It was the easiest thing ever and i'm a woman!
Was this helpful?
Thank you for voting!
oven would not lite
1 person found this instruction helpful.
  • david from canastota, NY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite
Was this helpful?
Thank you for voting!
over draw was off track
1 person found this instruction helpful.
  • Frances from Hauppauge, NY
  • Really Easy
  • Less than 15 mins
the part snapped on the side of the track, now the draw is not sitting on the floor and opens and closes like new.
Was this helpful?
Thank you for voting!
One guide was missing and the other was broken
1 person found this instruction helpful.
  • Don from WEST UNION, OH
  • Really Easy
  • Less than 15 mins
Read the instructions provided and simply installed the guides. Total time was less than 5 min.
Was this helpful?
Thank you for voting!
Replace Drip Pans
1 person found this instruction helpful.
  • Gary from REDFORD, MI
  • Very Easy
  • Less than 15 mins
No Problem, couldn't find them at any local repair facility so I looked on line and found them here, ordered 4 drip pans and the exact replacements came within a few days.
Was this helpful?
Thank you for voting!
Needed an additional rack
1 person found this instruction helpful.
  • Gary from Darragh, PA
  • Really Easy
  • Less than 15 mins
Open the door and slide in the new rack.
Was this helpful?
Thank you for voting!
would not light oven
1 person found this instruction helpful.
  • Richard from Huston, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
take off the old by unsceawing it scraw thenew one onput the wires down the back throw the hole put the wires to gather and cap tham plug the elect. back in and turn it on for to test it wow it worked he he ...richard
Was this helpful?
Thank you for voting!
Oven would not come on, broiler worked and so did the burners
2 of 4 people found this instruction helpful.
  • Jackie from Palmdale, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
And re-connected the same way.
Peice of cake..

Thank You..
Was this helpful?
Thank you for voting!
guide was broken
1 person found this instruction helpful.
  • Marvin from MONTANA CITY, MT
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Used a slot screwdriver to pry the old guide...clipped the new guide into its place.
Was this helpful?
Thank you for voting!
oven would not lite
1 person found this instruction helpful.
  • Walter from Danville, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver
First i removed the broiler door and then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and cut the two wires. I strip the ends ,connected the new unit with ceramic nuts that was provided an reconnected the unit. all was done in less than 30 min. EASY!!! plug the stove back in and WORKED PERFECTLY. note i receive the unit the same day it shipped....WOW
Was this helpful?
Thank you for voting!
oven would not light
2 of 4 people found this instruction helpful.
  • larry from 775, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
pulled drawer out and took old igniter off and replaced it
Was this helpful?
Thank you for voting!
ignitor wears out, tenants use the stoves as heat sorce
1 person found this instruction helpful.
  • jODY from GREAT FALLS, MT
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Opened the oven, removed the bottom plate located the ignitor within arms reach, removed two screws and a snap out part. replaced with the new ignitor and put the stove bottom on and waala...DONE
I have ordered all my parts from Parts Select and have never had a problem. Thank you. Jody in Montana
Was this helpful?
Thank you for voting!
Oven would not turn on , igniter burned out
1 person found this instruction helpful.
  • James from Ogdensburg, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
1. Removed top over the oven burner.
2. cut the two wires conneted to the igniter about
an inch and a half.Noted which wire goes to the top of the igniter and which one went to the bottom.
3. unscrewed the igniter from the mount and
carefully pulled it from the oven.
4. put the new igniter wires through the hole.
5. mounted the igniter to the burner.
6. attached the new wires to the top and bottom old wires with the connectors that came with the igniter.
7. pluged the range back in and turned on the oven. Igniter works great.
Was this helpful?
Thank you for voting!
All Instructions for the GF950ND2
91 - 105 of 405