EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GF950ND2 Frigidaire Range - Instructions

All Instructions for the GF950ND2
76 - 90 of 405

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not light up
2 of 2 people found this instruction helpful.
  • John from St.Albans Bay, VT
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
Remove oven racks and bottom oven panel cover.Removed old igniter.one screw was stripped so that slowed me down quite a bit! Used a small vise grip tool to remove screw! installed new ignighter,cut existing wires; spliced in new wires( be sure to unplug appliance) tested ok. Reassembled.
Was this helpful?
Thank you for voting!
weak oven igniter/not enough amp. to light oven
3 of 6 people found this instruction helpful.
  • JEFFREY from ULSTER, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
first I removed oven draw for access, then removed the two screws with a nut driver, next removed the two wire nuts and the old element was free. Replaced new element in reverse steps of removing old and the new part ignited the stove within 30 seconds, but now I have no excuse for not fixing dinner!! Thanks for promt shipping, it arri ved early than anticipated.
Was this helpful?
Thank you for voting!
Broken drawer slide
2 of 3 people found this instruction helpful.
  • Michael from Jacksboro, TN
  • Really Easy
  • Less than 15 mins
Remove drawer. Insert new slide. Install drawer.
Was this helpful?
Thank you for voting!
Broken right side parts for lower over storage drawer.
2 of 3 people found this instruction helpful.
  • Ty from Baltimore, MD
  • Easy
  • Less than 15 mins
  • Screw drivers
Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.
Was this helpful?
Thank you for voting!
Lacking oven racks on used appliance
2 of 3 people found this instruction helpful.
  • Katherine from Roanoke, VA
  • Really Easy
  • Less than 15 mins
Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!
Was this helpful?
Thank you for voting!
The right Drawer Glide was broken.
2 of 3 people found this instruction helpful.
  • Fred from Gregory, MI
  • Really Easy
  • Less than 15 mins
The simplest repair ever! I just snapped it in and put the drawer back - fixed. I hope I have other repairs this simple.
Was this helpful?
Thank you for voting!
Took a long time to light oven, smell of gas, slow heat up.
2 of 3 people found this instruction helpful.
  • Todd from OLYMPIA, WA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Really easy to do, did not have to bring stove out from the wall! Turn power off to the stove. Remove the lower drawer. Remove the oven rakes. With a slotted screwdriver remove two screws in back of bottom oven cover, use 1/4 inch socket to remove two screws in front. Remove bottom oven cover. You can then see the part to be removed whi ch has two wires going into it, the unit looks identical to the new part which heats up and lights the gas grill for the oven. I cut the two wires from the old part, remember which is the upper and lower; remove two screws holding onto part. Wire new part remembering top and bottom. Push extra wire down into bottom drawer and then mount new part with two screws. Turn power back on and try oven. Lite right away for me so I knew I had replaced the bad part. Reassemble and Enjoy!!
Was this helpful?
Thank you for voting!
my oven wouldn't light
1 person found this instruction helpful.
  • david from granville summit, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
first i removed the bottom of the oven [inside the oven] ,the part was right there,i removed 2 screws and unpluged the wires,then i cut the wire ends off the old part and used the wirenuts that came with the new one to hook them to the new part,then put it back in place,put the screws back in put the bottom back in and was done
Was this helpful?
Thank you for voting!
Oven would not heat.
1 person found this instruction helpful.
  • Jody from Storrs Manfield, CT
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Turned the gas and the electricity off to the gas range. Took the two large screws out in the back of the range holding on the first pan. Have to look for them. Took off the single nut holding on the second pan. Used nut drive #10 to take off nuts. Be careful you do not lose them. Took off inoperative unit. Cut wires to unit. Stripp ed wires which connect to range. Put new unit on and tightened nuts with nutdriver. Spliced wires together and put on wire nuts securely. Taped them to the wires. Put the second pan back, then the first pan. Turned on gas and electricity to test.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.
Was this helpful?
Thank you for voting!
occasional failure to light-wife didn't trust it.
1 person found this instruction helpful.
  • Carroll from Jackson, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Removed oven door. (two screws)
Removed racks.
Removed oven floor. (two finger screws)
Removed diverter (V) tray. (one nut)
Removed small panel @ left lower back of oven
(1 screw) to access elect. power disconnect.
Disconnected power.
Removed element (two square drive screws)
Snipped and stripped ol d wires, connected new
with ceramic wire nuts supplied.
Installed new element, reversed proceedure.
Oven lights in 10 seconds. Wife happy!
Probably 40 minutes, could do it again in15-20
once you know what tools to lay out.
Was this helpful?
Thank you for voting!
oven wouldn't light uneven temp.
1 person found this instruction helpful.
  • Paul from Akron, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
had to remove burner bolts holding igniter were stripped cut two wires replaced igniter using two self tapping screws put wires together using wirenuts Honey making cookies right now thanks already told friends about you
Was this helpful?
Thank you for voting!
Oven wouldn't light off
1 person found this instruction helpful.
  • Mickey from Fallbrook, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.
Was this helpful?
Thank you for voting!
oven wont start
1 person found this instruction helpful.
  • ismael from perth amboy, NJ
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires....install new element and woalla.........save thangsguivingday thanks to part select .com..........
Was this helpful?
Thank you for voting!
originaldrawer guide was cruched out of useable shape
1 person found this instruction helpful.
  • Fred from Ocala, FL
  • Really Easy
  • Less than 15 mins
  • Pliers
first thing was to remove the crushed guide with pliers and a twist it was out. to install the new one islipped one side into the slot and took pliers and applied pressure on the lower glide into the slot; it was done presto. works like new. thanks,
Fred . it was so reasonable i got a spare.
Was this helpful?
Thank you for voting!
oven drawer would not open or shut completely
1 person found this instruction helpful.
  • Howard from Poteau, OK
  • Really Easy
  • Less than 15 mins
  • Screw drivers
first I emptied the contents of the drawer,then pulled drawer open to it's fullest, then lifted drawer so as to tilt slightly, then removed drawer by continuing to pull straight out. then I removed the glide from its protective packaging and inserted it in the same spot as the broken glide was at one time
Was this helpful?
Thank you for voting!
All Instructions for the GF950ND2
76 - 90 of 405