FGF337GBA Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
light bilb went out
2 of 6 people
found this instruction helpful.
-
Denise from Landover, MD
- Really Easy
- Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
Knob lost middle metal clamp
0 of 1 people
found this instruction helpful.
-
Holly from Tampa, FL
- Easy
- Less than 15 mins
Received part very next day and put new knob on. Matches perfectly.
Was this helpful?
Thank you for voting!
Oven would not get up or stay up to selected temperature
0 of 1 people
found this instruction helpful.
-
wondell from Winnemucca, NV
- Easy
- Less than 15 mins
-
Nutdriver
Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to joi
... Read more
n the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)
Read less
Was this helpful?
Thank you for voting!
Two of theTop gas burners would not spark
0 of 2 people
found this instruction helpful.
-
Robert R from Lewistown, PA
- Easy
- Less than 15 mins
Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.
Was this helpful?
Thank you for voting!
Cracked inside glass
0 of 2 people
found this instruction helpful.
-
patti from Greer, SC
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti
Was this helpful?
Thank you for voting!
Replace Igniter
28 of 89 people
found this instruction helpful.
-
Anna from Mt Vernon, NY
- A Bit Difficult
- 15 - 30 mins
-
Wrench (Adjustable), Wrench set
PartsSelect.com saved me lots of $$$$$. I have had appliance repairers come and view the stove and tell me I needed so much work. I paid them and the stove still wasn't fixed. I figured out the problem and found PartsSelect.com = savior!
Was this helpful?
Thank you for voting!
electronic temp controller went bad
-
david from reynoldsville, PA
- Easy
- 15 - 30 mins
-
Nutdriver
first unplug oven. then remove upper back panel(6 screws)with a 1/4 nut driver. next unplug electical connector from control unit. then remove unit by removing (4 screws on corners of unit with 1/4 nut driver. replace unit with new one and reassemble in reverse order.
Was this helpful?
Thank you for voting!
No heat from bottom or top element,k stove top and clock all worked fine.
-
steven from Daleville, AL
- Easy
- 15 - 30 mins
-
Screw drivers
Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on
... Read more
the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.
Read less
Was this helpful?
Thank you for voting!
oven wouldn't work
-
Steve from Hiram, OH
- Easy
- 15 - 30 mins
-
Nutdriver
Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven ba
... Read more
ck in. Done.
Read less
Was this helpful?
Thank you for voting!
really bad ugly streaks inside of glass
-
John from Hemet, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door
... Read more
. Just reverse the way you take it apart to put it back together.
Read less
Was this helpful?
Thank you for voting!
inner glass uncleanable
-
Krista from Newtown, CT
- Easy
- 15 - 30 mins
-
Screw drivers
Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair
Was this helpful?
Thank you for voting!
no heat in oven
-
BARBARA from NORTH PORT, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.
Was this helpful?
Thank you for voting!
Broken control panel housing
-
Marc from Gastonia, NC
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I actually had to buy two parts, the cover and the control panel. But unfortunately I could not get them from the same place. But I replaced the control panel and the cover in about 15 minutes. No issues. Everytihg lokks brand new and works like a new stove. So I am very pleased.
Was this helpful?
Thank you for voting!
old oven racks were nasty!
-
Richard from Fort Wayne, IN
- Really Easy
- Less than 15 mins
We recently purchased condo and WhiteWestinghouse range needed some love. the old racks were not in very good shape so we ordered new.
Was this helpful?
Thank you for voting!
Sliced Outlet Cord
-
William from Saint Clair Shores, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part
... Read more
number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.
Read less
Was this helpful?
Thank you for voting!