EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

FGF337GBA Frigidaire Range - Instructions

All Instructions for the FGF337GBA
91 - 105 of 133

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
55 yr old wall oven had burnt out seal
  • Diane from Natrona Heights, PA
  • Really Easy
  • Less than 15 mins
Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket
Was this helpful?
Thank you for voting!
Gasket In Door Replaced
  • James from Greenville, TX
  • Really Easy
  • Less than 15 mins
The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.
Was this helpful?
Thank you for voting!
Foul ordor coming from stove
  • Joe De from Montgomery, AL
  • Easy
  • 15 - 30 mins
  • Socket set
The foul order was the cause of a "Mummified Rat" that I found on the bottom Left /outside wall of the oven. I first Unplugged the stove and turned off the gas. I removed the grates and the burners. Each burner is held down with two (2) 3/16" screws which makes it a total of eight (8) screws in all. After removing all eight screws, yo u can now pop up the burner lid with a putty knife or a large Screw Driver. I used a large screw driver, After removing the "Lid" you will then see the "Insulation Blanket" draped over the oven, to remove this blanket there are two (2) copper wires securing the blanket in place, you'll have to cut these in order to install your New Blanket. Removing the "Blanket " is a "No Brainer" just be cautious and don't snag any of the "Igniter Wires" The "Insulation Blanket" goes on one way, this can be identified by the pre-cuts on the blanket. I started out on the left side of the stove, and had the right side of the "Blanket rolled up. As I tucked the "Blanket" under the "igniter Wires" and slowly and gently feeding it with my left hand till it lines up with the pre-cut and drapes itself into place as you maneuver it down with your hands Now start with the right side by unrolling the "Blanket" and following the same procedure making sure the "Insulation Blanket" is fully extended on both sides of the oven.
Was this helpful?
Thank you for voting!
The oven control board did not respond and was kicking out the GFI
  • MELVIN from ST LOUIS, MO
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I replaced the oven control board. I used the old overlay because I could not find a model # but I was able to locate the exact replacement part. it took some to find, but it paided off.Thanks for your help. I Got the replacement part # from the old control board.
Was this helpful?
Thank you for voting!
Oven Temperture probe.
  • Kenneth from Edgemount, SD
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.
Was this helpful?
Thank you for voting!
Bottom Panel of over rusted out.
  • Michael from Manasquan, NJ
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as t his prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.
Was this helpful?
Thank you for voting!
burner would not light
  • Matthew from Gladwin, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Wrench set
We took off all of the bolts holding the burner assembly's in place . Then took the top of the s range off. Used a wrench to remove the old assembly and re-placed it with the new one. It took longer to get all of the top and under cover off then to put the new part in. Very good service from Part Select. MATT
Was this helpful?
Thank you for voting!
The housing around the clock/timer shattered
  • Sara from Tomball, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
We turned off the gas, moved the stove out from the wall and unplugged it. Then we removed the metal back (using an adjustable wrench because we didn't have a square headed screwdriver.) We then removed the four screws that had held the clock/timer in place before the plastic shattered. We inserted the new part and reinserted the screw s. Then we replaced the back cover. When we plugged the range back in and set the clock everything worked beautifully.
Was this helpful?
Thank you for voting!
The Oven ignitor did not turn spark for the oven to turn on and heat up.
  • Ricardo from Brooklyn, NY
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I pulled the top cover from inside the oven off and unscrewed 2 screws to remove the heat plate. After i unplugged the adapter for the old ignitor apart and unplugged 2 wires and removed 2 screws that hole the ignitor to the plate. i replaced with the new ignitor, screwed back in place , plugged the 2 wires and the adaptor plug in and i was done , in less that 30 mins.. I also saved $180 (Sears $260) on this do it yourself repair.. Thanks PartSelect for having the part in stock.... R Diaz (Bklyn N.Y.)
Was this helpful?
Thank you for voting!
Oven Wouldn't Turn On (F-10) Displayed
  • DAVID from PALMDALE, CA
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
I thought it was the temperature sensor. I was wrong it was the e. O. C. It wasn't that hard to change,just alot of small screws. Once I plugged it in I tryed to turn on the oven it turned on right away. Only thing is I wish the part was cheaper & also there should have been a white cover on it. Not peel off the old one and re-use i t???? The oven is only 2yr's old, but never the less it got fixed. . . Works fine now.
Was this helpful?
Thank you for voting!
I needed an extra oven rack to bake more at one time.
  • Sally from Cincinnati, OH
  • Really Easy
  • Less than 15 mins
I just installed the extra rack and re-arranged the existing ones. Works great!
Was this helpful?
Thank you for voting!
broken door trim
  • Carol from Corpus Christi, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
simple to unscrew the door handle from the inside, remove the broken trim, place new trim on, clamp the door together, then screw the handle back on. Went well!
Was this helpful?
Thank you for voting!
Just had to replace the racks in the stove.
  • charles from El Paso, TX
  • Really Easy
  • Less than 15 mins
Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks
Was this helpful?
Thank you for voting!
Old rusty worn out oven racks
  • June from Mt. Vernon, AL
  • Really Easy
  • Less than 15 mins
Removed the old oven racks and put in the new ones.
Was this helpful?
Thank you for voting!
I had the top trim broken on the oven door.
  • Fanny from Alhambra, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
Very simple repair. I received my part a few days after placing order; then installed it myself. Anyone can do this simple easy repair.
Was this helpful?
Thank you for voting!
All Instructions for the FGF337GBA
91 - 105 of 133