EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

AS2126PIHW Maytag Refrigerator - Instructions

All Instructions for the AS2126PIHW
46 - 60 of 123

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light rocker switch broke and refrigerator light couldn't go on.
2 of 4 people found this instruction helpful.
  • Cathy from HOPATCONG, NJ
  • Very Easy
  • Less than 15 mins
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this helpful?
Thank you for voting!
Ice maker ejector arm broke into.
16 of 46 people found this instruction helpful.
  • Mary L. from Millsboro,, DE
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed old ejector arm and installed new part.
Was this helpful?
Thank you for voting!
Ice maker broken. Quick fix
1 person found this instruction helpful.
  • Tim from Berkeley, CA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!
Was this helpful?
Thank you for voting!
broken hinge bearing on ice maker
3 of 7 people found this instruction helpful.
  • ROBERT from WESTFIELD, IN
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove , 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY
Was this helpful?
Thank you for voting!
Frig door wouldn't close on its own
1 person found this instruction helpful.
  • Al from Aztec, NM
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Emptied the door by taking out all the shelves with their contents. Removed the upper door closer works. Removed the door by lifting up and away from the main box. Layed the door on its side. Took out the old lower hinge pin and door closer with cup. Put in the new lower hinge pin and door closer with cup. Applied sewing machine gea r grease to the 2 pieces where they work together. Lifted the door and placed the lower hinge pin into the door closer with cup. Replaced the upper door closer works.
Was this helpful?
Thank you for voting!
ice maker kept on dripping water causing ice in the icee containergood compression to freeze in a block
1 person found this instruction helpful.
  • Fernand from SOMERSET, MA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
ordered a new shut-off valve. arrived in 5 days. installation had to wait a couple more day for i had to order a new compression nut. the reason i had to order a new nut was because the original nut was made of teflon and stripped easily when i tightened it to make a leak proof.joint. the new nut arrived in two days and was installed re adily being that it was made of brass and consequently did not strip when i tightened to make a drip proof joint. finished in approximately twenty minutes' the video that this site has on the internet was of great value.
Was this helpful?
Thank you for voting!
Refrigerator door would not self close. Had to physically close it.
1 of 2 people found this instruction helpful.
  • Thomas from Easton, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set
Replacing the hinge pin itself is really easy. Most important is to brace the bottom of the door before replacing the pin, otherwise the door will drop as the bottom hinge must be removed to install the new pin.

A couple of short lengths of 2x4s used to brace the door bottom worked fine. With these in place the door did not dr op down after removing the hinge. Replacement of the hinge and pin easy.
Was this helpful?
Thank you for voting!
The ice stripper cracked from freezing.
3 of 8 people found this instruction helpful.
  • David from Discovery Bay, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.
Was this helpful?
Thank you for voting!
light did not work on the refrigerator side
1 of 2 people found this instruction helpful.
  • David from GROVESPRING, MO
  • Easy
  • Less than 15 mins
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i s inside the refer!
Was this helpful?
Thank you for voting!
Light switch broke off
1 of 2 people found this instruction helpful.
  • Kathy from TEMECULA, CA
  • Very Easy
  • Less than 15 mins
  • Pliers
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this helpful?
Thank you for voting!
Rocker on switch broke off
1 of 2 people found this instruction helpful.
  • David Barnes from ROSWELL, NM
  • Very Easy
  • Less than 15 mins
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this helpful?
Thank you for voting!
Broken shelf
2 of 5 people found this instruction helpful.
  • Eric from Rumford, RI
  • Really Easy
  • Less than 15 mins
The repair was easy ... the big relief was finding a correct replacement for a fairly old appliance
Was this helpful?
Thank you for voting!
Door dragging causing it not to seal complete
1 of 2 people found this instruction helpful.
  • dana from winston-salem, NC
  • Really Easy
  • Less than 15 mins
  • Socket set
First I removed the three screws in the top hinge that hold the upper right corner of the door to the body of the unit. Then I just lifted the door off of the refrigerator. I proped the door up just long enough to pull out the old pin (plastic) and put the new one in place. Next I picked up the door and set it on the new hinge, and las t I put the three screws back into place. It has taken me about as long to type this out as it did to actually make the repair. The part was also very reasonably priced so I purchased two since this items has been replaced previously.
Was this helpful?
Thank you for voting!
The old ice pan for the icemaker was broken
1 of 3 people found this instruction helpful.
  • James from Lutz, FL
  • Really Easy
  • Less than 15 mins
I opened the box, unwrapped the new ice pan, gave it a cursory rinse, and put it in the freezer.
Was this helpful?
Thank you for voting!
Door Light switch cracked Mounting
0 of 1 people found this instruction helpful.
  • Paul from Hinsdale, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights we re staying on (50 watts of heating). Replaced the switch and the frig started working like new.
Was this helpful?
Thank you for voting!
All Instructions for the AS2126PIHW
46 - 60 of 123