- Home
- AS2126PIHW
- Instructions
AS2126PIHW Maytag Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
lights wouldn't come on/work in refrigerator
4 of 6 people
found this instruction helpful.
-
Jane from Albuquerque, NM
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80..
... Read more
.would have been at least $100 to have a repair person come to the house!
Read less
Was this helpful?
Thank you for voting!
The lightbulb burned out
3 of 3 people
found this instruction helpful.
-
Jennie from ASHEVILLE, NC
- Very Difficult
- More than 2 hours
Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.
Was this helpful?
Thank you for voting!
changed the light bulb still would not work so I figured it was the switch sure enough.
3 of 4 people
found this instruction helpful.
-
anthony from HAVELOCK, NC
- Really Easy
- 15 - 30 mins
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this helpful?
Thank you for voting!
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
3 of 4 people
found this instruction helpful.
-
David from Hemet, CA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull t
... Read more
he connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Read less
Was this helpful?
Thank you for voting!
door would not close and seal on it own
3 of 4 people
found this instruction helpful.
-
chad from st. Louis, MO
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
removed three nuts from the top of the door diconected the electrical connections for the ice and water in the door. Removed door by lifting it up about 2 inches, set it aside put new hinge pieces in placed put everything back together. writing this took more time. wanted to add, bought at 2 pm on thursday was at my house by 10am the n
... Read more
ext day
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
defective light switch
3 of 4 people
found this instruction helpful.
-
THOMAS from WILLARD, OH
- Really Easy
- Less than 15 mins
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 people
found this instruction helpful.
-
Thomas from Roseville, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 people
found this instruction helpful.
-
stu from richmond, VA
- Easy
- Less than 15 mins
-
Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 people
found this instruction helpful.
-
dorotea from staten island, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
Lower hinge broke, causing the door to jump when open
2 of 2 people
found this instruction helpful.
-
Vadim from Flanders, NJ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
It is the model with the french door. I unplugged it, removed two screws at the bottom of the door, while holding the door from sliding down. Removed the door and put it on its side. Removed one screw that was holding the hinge, removed the hinge and replaced it with the new one. Put the door back on (do not forget to reinstall the shims)
... Read more
.
Did the same thing on the other door. After putting the door back on readjusted the height to level the door, using height adjustment screw. Lock the door in place. It now works better then new
Did the same thing on the other door. After putting the door back on readjusted the height to level the door, using height adjustment screw. Lock the door in place. It now works better then new
Read less
Was this helpful?
Thank you for voting!
Door started to sag causing it not to close correctly
2 of 3 people
found this instruction helpful.
-
Jason from Colorado Springs, CO
- Really Easy
- 15 - 30 mins
-
Socket set
Took door off refrigerator and removed worn parts and replaced the aforementioned parts, which took only a few minutes.
Other Parts Used:
Was this helpful?
Thank you for voting!
Ice from icemaker taste metallic; new ice maker directly from box
2 of 3 people
found this instruction helpful.
-
Samuel from ALEXANDRIA, VA
- Difficult
- More than 2 hours
I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 people
found this instruction helpful.
-
Gail from Golden, CO
- Really Easy
- Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
Ice catcher was missing from the icemaker
3 of 7 people
found this instruction helpful.
-
Charlotte from Cambridge, MA
- Really Easy
- Less than 15 mins
I removed the ice catcher from the excellent packaging, rinsed it, and placed it on the counter next to the fridge. I opened the door the the freezer and placed the ice catcher under the icemaker. I lowered the arm on the icemaker and closed the door to the freezer. Then I opened the door to fridge, took out a Guinness, popped the top,
... Read more
and sat down to savor my success.
Read less
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 people
found this instruction helpful.
-
Carolee from Spokane Valley, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!