EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

AS2126PIHW Maytag Refrigerator - Instructions

All Instructions for the AS2126PIHW
16 - 30 of 123

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
replacing thermostat did not help
10 of 15 people found this instruction helpful.
  • John from Rocky River, OH
  • Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set
Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiv er boaed. I turn off manually the icemaker, when needed
Was this helpful?
Thank you for voting!
Broken Piece
7 of 8 people found this instruction helpful.
  • anthony from georgetown, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Had to disassemble ice maker to install part. . .
Was this helpful?
Thank you for voting!
light not working in fridge
7 of 8 people found this instruction helpful.
  • Michael from East Meadow, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!
Was this helpful?
Thank you for voting!
frig got warm, compressor would not turn on, heard clicking noise
7 of 9 people found this instruction helpful.
  • Jeff from Cherry Hill, NJ
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
googled for answer, deduced relay/switch problem. googled again for parts, found partselect.com, ordered part. 2 days later & $70 lighter, my 8yr old Maytag was working again! Parts were good fit, instructions were decent enough. Not for inexperienced tinkerer though.
Was this helpful?
Thank you for voting!
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
7 of 10 people found this instruction helpful.
  • Antonio from San Antonio, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Was this helpful?
Thank you for voting!
The Switch Broke...Absolutely Fell Apart.
5 of 5 people found this instruction helpful.
  • Duncan from Metairie, LA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this helpful?
Thank you for voting!
Icemaker fill tube cracked
5 of 5 people found this instruction helpful.
  • Mark from SEBASTOPOL, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
The factory installed fill tube was formed and molded, hard plastic. Nothing like the replacement part or the one depicted in the install instructions.To remove it, I had to grip the exterior water tube module with a pair of Visegrip pliers, twist and pull as hard as possible, to expose a section of fill tube. I then had to cut through th e tube with a hacksaw to remove the module and flange that secure it to the access hole. From the inside, I removed the ice maker and fan shield to expose the remaining section of fill tube. Using a section of copper pipe and a hammer, I was able to drive the tube through the back wall of the appliance. Fitting the new tube was easy. However, it is too short to reach the fill cup. I fashioned a section of the old tube to create an extension which I inserted in the new part. And, much to my surprise, it actually works!
Was this helpful?
Thank you for voting!
Replace broken ice cube trays
5 of 6 people found this instruction helpful.
  • C MARTIN from TAMPA, FL
  • Really Easy
  • Less than 15 mins
No repair needed. I had only to wash the new ones and use them.
Was this helpful?
Thank you for voting!
Refrigerator light would not stay on
4 of 4 people found this instruction helpful.
  • Dave from Manchester Center, VT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
Was this helpful?
Thank you for voting!
Light in my refrigerator didn't work.
5 of 7 people found this instruction helpful.
  • Joseph from Byron Center, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved m e $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.
Was this helpful?
Thank you for voting!
Water Fill Cup Broke
5 of 7 people found this instruction helpful.
  • Sam from Las Vegas, NV
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.
Was this helpful?
Thank you for voting!
Trim was not staying place and the hinge cover was cracked
5 of 8 people found this instruction helpful.
  • Alexis J from Lanham, MD
  • Really Easy
  • Less than 15 mins
I went straight to PartsSelect on line and within minutes I found the appropriate brand of parts for my refrigerator. I simply removed the old trim shelf and snapped the replacements in place. I also inserted the glass shelf trim. No tools were required.
Was this helpful?
Thank you for voting!
Raplaced switch
5 of 9 people found this instruction helpful.
  • Winston A from Brooklyn, NY
  • Really Easy
  • Less than 15 mins
  • Pliers
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this helpful?
Thank you for voting!
wife broke glass shelf
6 of 12 people found this instruction helpful.
  • Roger from Schenectady, NY
  • Really Easy
  • Less than 15 mins
replaced shelf
Was this helpful?
Thank you for voting!
Fill cup broke.
6 of 12 people found this instruction helpful.
  • Aliki from Miami, FL
  • Really Easy
  • Less than 15 mins
Very easy to order from parts select. Took seconds to replace.
Was this helpful?
Thank you for voting!
All Instructions for the AS2126PIHW
16 - 30 of 123