- Home
- AS2126PIHW
- Instructions
AS2126PIHW Maytag Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Screws on the door of the dishwasher were very loose.
1 of 6 people
found this instruction helpful.
-
Kathryn from Carol Stream, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Was this helpful?
Thank you for voting!
Water was running out of ice maker tray.
2 of 9 people
found this instruction helpful.
-
Lynn from Marshall, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
unscrewed the old one! installed the new one! That simple. And I'm female, how easy was that!
Was this helpful?
Thank you for voting!
Switch was not working after a repairman had fixed something else
0 of 4 people
found this instruction helpful.
-
Jackie from Nova, OH
- Really Easy
- Less than 15 mins
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a
... Read more
single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Read less
Was this helpful?
Thank you for voting!
Ice Stripper was broke off, leaving the mounting tabs still inside their respected spaces in the ice-maker
2 of 10 people
found this instruction helpful.
-
Jason from Draper, UT
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mo
... Read more
unting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.
Read less
Was this helpful?
Thank you for voting!
Fridge way too cold
2 of 13 people
found this instruction helpful.
-
John from Morris, NY
- A Bit Difficult
- More than 2 hours
Called a serviceman. The Air return cover is NOT the cover we replaced. Ours is 3/4 of the way down on the freezer side of fridge. Put a thermometer inside, to monitor it.
Was this helpful?
Thank you for voting!
Both light bulbs had been replaced, but lights did not turn on.
-
Richard from Arlington, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this helpful?
Thank you for voting!
Had to completely remove the ice maker in order to install the replacement part
-
Leonard W from Roseburg, OR
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The cha
... Read more
llenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.
Read less
Was this helpful?
Thank you for voting!
Ordered ejector arm.
-
Joyce from Springfield, MO
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.
Was this helpful?
Thank you for voting!
Compressor would not run.
-
Chad from Lexington, KY
- Easy
- 15 - 30 mins
-
Screw drivers
Replacement parts looked different than the originals, however with the on-line feedback from similar customers and a well worded OM, the repair was quick and simple. Thanks to all.
Was this helpful?
Thank you for voting!
Part Where Ice Maker Arm Fit In Broke Off
-
Yvonne from Worthington, IA
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect
Was this helpful?
Thank you for voting!
Broke the arm off the food compartment rocker switch
-
David from St. Pete Beach, FL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips
... Read more
were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Read less
Was this helpful?
Thank you for voting!
freezer normally functioning, refrigirator side too warm
-
Joseph from Hamburg, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I watched the instructional video included with the shipping date e-mail(about 3 minutes long), and simply followed the instructions. It took about 2 days for the refrigirator section to return to normal cool temperature to the level set.
Was this helpful?
Thank you for voting!
broken water fill cup
-
augustine from cedar rapids, IA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together
Was this helpful?
Thank you for voting!
Switch didn't work
-
Don from Laramie, WY
- Easy
- 15 - 30 mins
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this helpful?
Thank you for voting!
Light switch in the refrigerator was faulty from the first day we installed the fridge.
-
Mary from Wasilla, AK
- Easy
- Less than 15 mins
-
Screw drivers
I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world whe
... Read more
re my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!
Read less
Was this helpful?
Thank you for voting!